The work presented in this thesis reports the use of a series of novel thiobiuret metal complexes [M(SON(CNiPr2)2)n] (M = Cu, Ni, Fe, Zn, Cd or In; n = 2 or 3) for the first time as single source precursors for the colloidal synthesis of metal sulfide nanoparticles. Other single source precursor(s) were also used for the synthesis of CdSe, CdS, CdSe/CdS core/shell, CdSeS alloys and Cu2-xS nanoparticles in microfluidic reactors. Thermolysis experiments of [Cu(SON(CNiPr2)2)2] using only oleylamine produced Cu7S4 nanoparticles as a mixture of monoclinic and orthorhombic phases. Pure orthorhombic Cu7S4 nanoparticles were obtained when a solution of precursor in octadecene was injected into hot oleylamine whereas, Cu1.94S nanoparticles were obtained when a solution of the precursor in oleylamine was injected into hot dodecanethiol. The thermolysis of [Ni(SON(CNiPr2)2)2] gave Ni3S4 in all cases except when precursor solution in oleylamine was injected into hot octadecene which produced NiS nanoparticles. The thermolysis of [Fe(SON(CNiPr2)2)3] in oleylamine/oleylamine produced Fe7S8 nanoparticles but other combinations, in most cases, gave amorphous material. Thermolysis of [Zn(SON(CNiPr2)2)2] in oleylamine produced spherical ZnS nanoparticles. Particles with size smaller than 4.3 nm had a cubic phase, whereas the particles with size larger than 4.3 nm had a hexagonal crystal structure as suggested by the selected area electron diffraction. Powder X-Ray diffraction showed that the CdS nanoparticles obtained from the thermolysis of [Cd(SON(CNiPr2)2)2] in oleylamine were cubic under all reaction conditions except when dodecanethiol was used as an injection solvent which produced hexagonal CdS. β-In2S3 were synthesized from the thermolysis of [In(SON(CNiPr2)2)3]. Transmission electron microscopy showed that the copper, nickel and iron sulfide nanoparticles had various morphologies such as spherical, hexagonal disks, trigonal disks, rods or wires; depending on the reaction temperature, concentration of the precursor, the growth time and the solvent/capping agent combination. The zinc and cadmium sulfide nanoparticles were mostly spherical whereas the indium sulfide nanoparticles were produced in the form of ultra-thin (< 1.0 nm) nanorods or nanowires. ZnxCd1-xS and CuInS2 nanoparticles were synthesised from the 1,1,5,5-tetra-iso-propyl-4-thiobiureto complexes of Zn, Cd and Cu, In, respectively. Powder X-Ray diffraction showed that the obtained ZnxCd1-xS nanoparticles are cubic under all reaction conditions. The ZnxCd1-xS nanoparticles had an average diameter between 3.5 to 6.4 nm as shown by transmission electron microscopy. The optical properties of the ZnxCd1-xS nanoparticles were highly dependent on the ZnS to CdS precursor ratio and the solvents/capping agents. Chalcopyrite (tetragonal), wurtzite (hexagonal) or a mixture of both CuInS2 nanoparticles were obtained depending on the reaction conditions. TEM showed that the CuInS2 nanoparticles could be synthesised with different morphologies (spherical, hexagonal, trigonal or cone). Luminescent CuInS2 nanoparticles were obtained only in the absence of oleylamine. [Cd(S2CNMenHex)2], [Cd(Se2P(iPr)2)2] and [Cu(SON(CNiPr2)2)2] were used as single source precursor(s) for the synthesis of CdS, CdSe, CdSe/CdS core/shell, CdSeS alloys and Cu2-xS in microfludic reactor. The CdS nanoparticles were in size range of 5.0 to 8.0 nm whereas the CdSe nanoparticles were ultra small (ca. 2 nm) with blue luminescence. The CdSe/CdS core/shell and the CdSeS alloys were bluish green or green luminescent depending on their size. The copper sulfide nanoparticles were found to be monoclinic Cu7S4 or monoclinic Cu7S4 with minor impurities of rhombohedral Cu9S5 depending on the reaction conditions.

No / The formulation of poorly water-soluble drugs is a challenging problem within pharmaceutical development. Recently, formulation using nanoparticles was highlighted as showing great potential to improve the dissolution and solubility characteristics of poorly water soluble drugs.

The self-assembly of polystyrene-stabilized cadmium sulfide nanoparticles (PS-CdS) with amphiphilic stabilizing chains of polystyrene-block-poly(acrylic acid) (PS-b-PAA) into colloidal quantum dot compound micelles (QDCMs) is studied on two-phase gas-liquid segmented microfluidic reactors. The resulting particle sizes are found to arise from the interplay of shear-induced coalescence and particle breakup, depending on a combination of chemical and flow conditions. Variation of water content, gas-to-liquid ratio, and total flow rate, enable control of QDCM sizes in the range of 140 – 40 nm. The flow-variable shear effect on similar microfluidic reactors is then applied to direct the solution self-assembly of a PS-b-PAA block copolymer into various micelle morphologies. The difference between off-chip and on-chip morphologies under identical chemical conditions is explained by a mechanism of shear-induced coalescence enabled by strong and localized on-chip shear fields, followed by intraparticle chain rearrangements to minimize local free energies. Time-dependent studies of these nanostructures reveal that on-chip kinetic structures will relax to global equilibrium given sufficient time off-chip. Further investigations into the effect of chemical variables on on-chip shear-induced morphologies reveal a combination of thermodynamic and kinetic effects, opening avenues for morphology control via combined chemical (bottom-up) and shear (top-down) forces. An equilibrium phase diagram of off-chip micelle morphologies is constructed and used in conjunction with kinetic considerations to rationalize on-chip mechanisms and morphologies, including cylinders and vesicles, under different chemical conditions. Finally, we extend our strategy of two-phase microfluidic self-assembly of PS-b-PAA to the loading of fluorescent hydrophobic probes (pyrene and naphthalene) with different affinities for the PS core. The on-chip loading approach provides a fast alternate to the slow off-chip method, with implications for the potential development for point-of-care devices for drug loading. On-chip loading results indicate that loading efficiencies are dependent on water content and, to a lesser extent, on flow rate; the results also suggest that the on-chip morphologies of the PS-b-PAA micelles are an important factor in the loading efficiencies. / Graduate