This project deals with design and study wireless security device. This device works in ISM band, created by two modules handling secure subject. Microprocessor AVR from company Atmel provides communication between these modules.

ecorative lighting strips could be used to the backlight of furniture, to creating a modern interior design. From an architectural point of view, this design is very difficult and requires a strong sense of aesthetics. More easier is to use the LED strips to the advertising trailers or to backlighting car parts. RGB strip will be powered by switching power supply with galvanic isolation. Colour will be changed by the combination of basic colours RGB, by using 3-channel PWM of Atmel microcontroller, controlled via a wireless module, providing two-way communication..

This paper is in introduction focused on review of robotic vacuum cleaning and evaluation of available products qualities. However the main focus of this paper is system design of all subsystems, control systems and PCD design of robot electronics. In this paper is also described a method for evaluating approximate distance of robot from the obstacle. There are also described problems of system design of IR proximity sensors. The last part of this work is development of control software for robot and its testing.

This semestral project is concerned with remote control PTZ camera using the wireless controller, and the controller design including design documents. The controller will be composed of the signal converter, microcontroller and RF module. Control data to the controller will come via link RS485 and controller will be able to communicate using the following protocols-Ernitec and Pelco. The proposed controller, according to data from the manufacturer to have a range of up to 500m. This parameter and also other transmission parameters confirm in the diploma thesis which will focus the actual implementation of the controller.

The master’s thesis deals with the methods and system for measurement of concentration of intracellular calcium in LabVIEW. The thesis included theoretical and practical parts. The thesis covers the theory of fluorescence principles, fluorescence methods and indicators for measurement of concentration of intracellular calcium. The procedure of measurement by means of fluorescence microscope, camera and indicators is also mentioned. Literary solution is presented. Block diagram of system for measurement of concentration of intracellular calcium at a graphical programming environment LabVIEW is presented in practical part of master’s thesis.

In this work I aimed at designing a universal system for testing either STM32F407/417 by STMicroelectronics and later various sensors and communication buses. The result then is a main board with many specific connectors for individual buses even with connectors making all I/O pins accessible at the same time. Thanks to advanced switching regulators the power supply is capable of accepting a wide range of sources like single Li-Ion cell, pair of alkaline cells, 12V Lead battery, common wall power adapters (both DC and AC up to 15 Vpp ), USB, laboratory power supplies with multiple outputs and finally POE (Power Over Ethernet). Supply voltages are supervised by voltage comparators with an optical signalisation. (It is possible to determine the sick branch without a measuring instrument and blowing components in the most cases.) Another important parameter was a robustness of the supply and communication lines. There is a number of TVSs, chokes, and big and low ESR capacitors A PC software is intended for a basic functionality demonstration only.

The cryptographic algorithms are commonly used as a security item today. In some situations, the special device is used to run the cryptographic algorithm, so the data are protected against the attack from the internet. Naturally, the attack can be loaded on the device as well using the side channel attack. The data are under the great danger, because nowadays plenty of power consumption analyses exist. The side channel attack uses knowledge about the cryptographic algoritm and simple or differential analysis. The diploma thesis focuses on the differential power analysis attack for the data published under the DPA contest. This thesis covers different types of analyss and attacks, and describes the new DPACv4.2 implementation. The correlation analysis is presented for the DPACv4.2 and the possible attack is discussed at the conclusion.

The focus of the work is the calculation and design of battery-powered drive of locomotive, operating in the sub-siding mode, ie when the locomotive is moving on the track section without the overhead line. The proposed battery groups to ensure the drive train will be installed directly into the locomotive engine room. In the theoretical part of the work there has been done the analysis of the electrical locomotives and electrical unit, which nowadays are used in the Czech Republic in driving of voltage controller with the integrated circuit. Then, in the chapter there is a brief description modern locomotives frequency convertor’s and rectifier’s function. The practical part of the work contains the necessary force and energy calculation for train moving on the determined rails. On the base of the received data, the design of battery groups has been done. These battery groups will work as an independent traction which insures the moving of the train on the determined rails. In the work the design, which consists of STEP-UP and STEP-DOWN convertors, has also been done. The power model and model management were created in Matlab Simulink programme. Data and graphs exported from the Matlab Simulink programm are determined for verifying convertor’s function, which can be found in a separate chapter. In addition to the proposal of the battery drive is at work also has been calculated loss of traction rectifier during normal operation of the locomotive, ie outside siding mode. For this calculation, in the conclusion is listed the theory of calculation of the losses incipient in the transistor and freewheeling diode of rectifier. According to the theory own calculation is performed. Subsequently the liquid cooler calculation of the rectifier is calculated.

The diploma thesis describes mobile communication systems GSM and UMTS including the operating principle of these systems. It also deals with the GPS issues and the determination of the location by this system. The signal path losses issues between the transmitter and receiver are also described. The focus is also put on Telit UC864-G model and the measurement system, operated by the created programme with the graphic user interface, which measures parameters of the cellular network according to entered input parameters and saves the measured values into the file. The part of the diploma thesis describes another created programme with the graphic user interface displaying the measured network parameters in map data with the possibility to compare the distribution of the measured signal value in both outdoor and indoor environment and the theoretical value set by the propagation models.

This thesis describes the design and subsequent implementation of a unit for traffic monitoring using Raspberry PI. First section provides a quick overview of assistance systems, which use a road lane detection techniques. Next there is a description of two diferent methods for road lane detection. Follow the description of monitoring scene. Then the work describe the practical part including the design and realization of supporting electronics, selecting of each components, including the modifying of cameras, mechanical design and creating of unit. Another section is about selection and installation of appropriate software components necessary for running of the unit and the selection of development tools for creating user application. After description of graphical user interafce, there is a description of road lanes detection algorithm. At the end of the thesis is summarized a reliability of unit in real traffic situation. At the appendix there are technical drawings, describing the unit.