The objective of this study is to develop a methodology to analyze the air quality and tool performance in turning process under near-dry condition. Near dry machining refers to the use of a very small amount of cutting fluid in the machining process. In order to implement the near dry machining technology, this dissertation develops the analytical models for both tool life and aerosol generation prediction. This research includes predictive models of cutting temperatures, cutting forces, tool wear progressions, and aerosol generation. The comparison of air quality and tool performance among dry machining process, near dry machining process, and flood cooling machining process is also presented. It is found that according to the selected cutting conditions in the model-based comparisons, the predicted cutting forces, cutting temperature and power consumption under near dry lubrication are reduced as high as about 30% compared with those in dry cutting but these predicted values are higher than those in wet cutting by about 10% under the same cutting conditions while the predicted tool wear land lengths are reduced by 60% compared with those in dry cutting but these values are higher than those in wet cutting about 1% under the same cutting conditions. However, the air quality for near dry machining with 12.5 ml/hr oil flow rate is worse than that for wet cutting due to different aerosol generation mechanisms.

In the literatures of investigating the coupling mechanism between laser diodes and fibers, Gaussian beam profile was used to describe the propagation of laser beams. But the real laser diode beams exist astigmatism. In order to understand the distributions of real laser diode beams, we used single-mode fiber interferometer to measure the near-field intensity and phase distributions of laser diodes. The nanometer aperture of taper fiber was used to scan through the horizontal and vertical directions across the maximal intensity point of the planes which were perpendicular to propagation axis to measure the intensity and phase distributions of laser diodes. In the measurement of phase distributions, these two single-mode fibers produced interference fringes through accepting laser beams. When the taper fiber scanned the optical field and the reference fiber kept a fixed distance from a laser diode for a stationary phase, the interference fringes shifted because of the phase difference of laser diodes change. In the measurement, in order to improve the stability of interference fringes and consider the aperture of taper fiber, we altered some experiment frameworks. There were four types of experimental framework. According to the experiment results of the near-field measurements, the measured beam widths along the horizontal and vertical directions at the laser diode facet were 4.11 £gm and 1.57 £gm respectively. The measured wavefront radius curvature were 6.59 £gm and 2.96 £gm in horizontal axis and vertical axis respectively. After Gaussian beam fitting, the beam widths along the horizontal and vertical directions at the laser diode facet were 4.04 £gm and 0.83 £gm respectively. The difference in beam widths between measured values and Gaussian fitting were 0.07 £gm and 0.74 £gm. The measured beam widths and the Gaussian beam curve fitting had similar results. We could see that the beam spread tendency in the z-axis for the laser beam which propagated in the z direction. In the phase distribution measurement, the measured wavefront radius curvatures and the theoretically calculated Gaussian beam values had a slight difference. The calculated wavefront radius curvatures at the laser diode facet were 11921.51 £gm and 3.48 £gm in horizontal axis and vertical axis respectively. They were 1809 times and 1.2 times of the measured values. The aperture of taper fiber was expanded because of the energy of laser beams, which also caused the spatial resolution degeneration. Moreover, the wavefront radius curvature in horizontal direction was biggish so the measurement framework also limited the ability of the phase distribution measurement. The above points were the reasons to cause the error of the phase distribution measurement. Furthermore, the measurement of the laser diode facet is under investigation.

In this study, we fabricated an electrically wavelength-tunable resonant-cavity light emitting diode (RCLED). It was achieved by the combination of an AlGaInAs quantum well structure with an intra-cavity liquid crystal material. In the phase modulator layer, we used nematic liquid crystal (NLC) and cholesteric liquid crystal (CLC), respectively, comparing their difference in the infrared-spectrum. When inserting NLC, the anisotropic properties of liquid crystal enable continuous tuning of mode emission along the extraordinary direction and provide a 58 nm tuning range. The optical characteristics of this device are polarization dependent. On the contrary, the CLC-based device is polarization independent because any polarization of incident light experiences the same averaged refractive index. However, the phase difference of CLC is less than NLC, only a 41 nm tuning range of this sample. We also simulated and discussed experimental results of NLC-based RCLED. The optical pumping of the active region is realized by a CW laser at 1064 nm wavelength and observed at room temperature.

As variation in pork tenderness has increased, identification of tenderness has become an industry need. This study consisted of 1208 pork loins randomly selected to test the efficacy of four automated grading techniques. Visible and near-infrared spectroscopy (VVNIR) (350-1830 nm wavelengths), bioelectrical impedance (EI) (resistance, reactance, phase angle, and partial capacitance), pH, and CIE L*, a* and b* color space values were used to predict chemical moisture and lipid, pH, Warner-Bratzler shear force (WBSF), and Slice shear force (SSF) on 13 d aged pork loins. The means and standard deviations for WBSF were (22.95 and 5.16) and SSF were (165.49 and 58.15). Prediction was based on stepwise linear regression and partial least squares regression. VNIR, pH, and color, when in combination, had the highest R^2 (0.19 and 0.21) for the prediction of WBSF and SSF, respectively. Partial least squares regression (PLSR) was used to remove autocorrelation between VNIR values. By using PLSR, with an R ^2 value of 0.49, 100 percent of the "tender" chops were correctly classified, 93 percent of the "intermediate" chops were correctly classified, and 92 percent of the "tough" chops were correctly classified into its category for WBSF. However, SSF was much lower (R^2 = 0.24) with only correctly placing 62 percent of the "tender" chops and only 48 percent of the "intermediate" and "tough" chops. Electrical impedance, alone or in combination with other technologies, either did not improve predictability of linear regression equations (increase R^2) or of PLSR models (increase R^2). Equations and models that included EI values had low R^2. When adding EI to the regression equation involving all variables, R^2 increased slightly from 0.19 to 0.21 in predicting WBSF, and from 0.21 to 0.25 for SSF. When pH or CIE L* color space values were included in linear regression or PLSR models to predict WBSF and SSF, R^2 values increased from 0.14 to 0.19 for WBSF, and 0.14 to 0.21 for SSF. pH played a large role in predicting WBSF and SSF, along with CIE L*. Thus, for an on-line situation, use of VNIR, pH, and color could be used to predict tenderness. Utilization of VNIR alone could be effective in predicting pork tenderness (WBSF). Using EI alone, or in combination with VNIR, would not provide acceptable prediction of WBSF or SSF. Use of VNIR with pH and color would improve the ability to predict tender and intermediate pork WBSF and SSF, but the additional improvement in accuracy may not be warranted based on the cost and additional time needed when using more than one technology.

Many scientific studies have been conducted on the Cretaceous-Paleogene boundary (KTB) in the Gulf coast region and, in particular, the Brazos River section in Falls County, Texas. Despite this, there remains much to be learned about the KTB and its depositional environment. Study of the KTB has been multidisciplinary, primarily in the fields of sedimentology and paleontology. Some researchers in these disciplines have questioned the consensus view of the placement of the KTB and subsequent interpretation of the timing of depositional events and mass extinction events. Geophysical methods have potential to provide additional understanding of the physical properties of the KTB. To date, study of the KTB has relied on point data and borehole information to create cross sections of the complex. Seismic refraction surveys can provide spatially continuous information on susburface horizons located adjacent to the KTB. In this study, seismic first-arrival traveltimes are processed with a tomographic modeling program to map the top of the hummocky cross-bedded sandstone (HCS), which is a key indicator of the deposition environment at the time of KTB boundary complex placement. The survey area is located at Cottonmouth Creek, a tributary of the Brazos River. Three seismic lines were surveyed, one across Cottonmouth Creek, and two parallel to the creek on either side. The data from the two parallel lines were processed using the 2-D seismic refraction tomography algorithm of Zelt and Smith. The reconstructed depth to the HCS in the survey area is approximately 6 m, with layer seismic velocities of 364, 1800, and 2200 m/s, respectively. Seismic tomography successfully mapped the HCS layer and reveals approximately 1 m amplitude undulations vertically and undulations on the order of several m horizontally. These variations are consistent with exposed surfaces of the HCS in the creek bed. Seismic refraction has been utilized successfully herein to map a key buried indicator, namely the top of the HCS layer, associated with the KTB complex. A detailed 3-D seismic refraction survey at this site is recommended to generate a high-resolution 2-D terrain map of the top of the HCS layer.

This thesis presents a computational analysis of the magnetic field of low-frequency power transmission lines, and the approaches to its suppression. First, according to the structure of Taiwan's three-phase A.C. transmission network, this research calculated the distribution of conducting wires' magnetic field under specific configuration by applying the theories of Near-field effect, Biot Savart's law, and double complex number. Second, this research explored the features of various approaches to magnetic field suppression with magnetic-field vector analyses and Matlab simulations. Finally, two magnetic-field cancellation methods, the ¡§circuit space arrangement¡¨ and ¡§time phase permutations¡¨ were adopted to investigate their magnetic effects under various structures and combinations of transmission lines. This study reveals that the magnetic field can be effectively suppressed by using appropriate configuration of transmission lines in space and phase. By applying the result to the design and construction of transmission lines, we can meet not only the requirements of magnetic field reduction, but also the needs of the least cost.

Pointe du Hoc overlooking the English Channel in Normandy, France was host to one of the most important military engagements of World War II. While the site is a valuable historic cultural resource, it is vulnerable to cliff collapses that already have endangered the observation post and Rudder?s command post. The observation post has been closed to visitors for some time due to safety concerns. Geophysical techniques have been used increasingly in recent years for slope stability investigation purposes. The objective of this study is to apply advanced 3?D resistivity tomography toward a detailed site stability assessment with special attention to the two at-risk buildings. 3?D resistivity tomography datasets at Pointe du Hoc in the presence of extreme topography and dense cultural clutter have been successfully acquired, inverted, and interpreted. The cliff stability in the areas around the two at?risk buildings has been analyzed. A hazard assessment scheme has been designed in which regions of high resistivity are interpreted as zones of open, dry fractures with a moderate mass movement potential. Regions of low resistivity are zones of wet, clay?filled fractures with a high mass movement potential. The observation post tomography results indicate that the highest mass movement hazard appears to be associated with the marine caverns at the base of the cliff that are positioned at the point of strongest wave attack. These caverns likely occupy the future site of development of a sea arch which will definitely threaten the observation post building. A high probability of a soil wedge failure is on the east?facing cliff edge close to the observation post that could damage or destroy the building. The mass movement potential at the Rudder?s command post area is low to moderate. The greatest risk is associated with soil wedge failures at the top of the cliffs. The resistivity geophysical data add great value to the natural geohazard assessment at Pointe du Hoc and constitute an integral component of an interdisciplinary approach to the problem of cultural resource preservation at the site. Geophysics is a non?invasive and relatively inexpensive technology that provides unique constraints which are unobtainable using traditional engineering geology methods for site characterization. However, the technology is difficult to master and the inherent limitations must be carefully understood to ensure a reliable geotechnical interpretation.

In this thesis, we propose the method to design tag antennas, which are suitable for radio frequency identification system. The fact that the tag antennas design comes with single layer printed circuit board can achieve cost down of the antennas. For the tag antennas, the aim is to design the RFID tag antenna operating in 860¡V960 MHz which are suitable for both the near- and far-field operations worldwide. The method we use to design tag antenna is the dual loop form with Bow-tie antenna, and we focus on the impedance conjugate matching between the RFID strap and antenna to increase impedance bandwidth and improve reading performance. We can adjust parameter to be suitable for different RFID strap in the design framework. The dual loop structure carries out power coupling efficiently in the near field and can allow the RFID strap to work even in the weak EM wave. According to the result of power coupling simulation, we analyze and discuss which factor will affect the reliability of the identification. Such reliability will help to build RFID system.

No description available.

Thesis (Ph. D.)--University of Washington, 2001. / Vita. Includes bibliographical references (p. 111-122).