Spelling suggestions: "subject:"hiyama"" "subject:"nishiyama""
1 |
Granskning av yogautövares uppfattningar om ekologisk hållbarhet : En kvalitativ studieSpajic, Ana-Marija January 2018 (has links)
Fem kvinnor som regelbundet utövar yoga har intervjuats för att undersöka hur deras uppfattning av ekologisk hållbarhet ser ut. Trots att samtliga intervjuade är uppväxta i olika länder - Sverige, Schweiz, Singapore, Filippinerna - är deras svar i hög grad överensstämmande med varandra. Det är värt att observera att svaren även stämmer väl överens med nyheter som rapporteras i media. De intervjuade har gett beskrivningar av de bekymmer de ser i miljön samt vilka initiativ de personligen tar till för att minska miljöförstörelse. Störst är temat för konsumtion / överkonsumtion, följt av reducering och återvinning. Det är möjligt att svaren är påverkade av media. Palmolja nämns inte under någon av intervjuerna trots att 3/5 av de intervjuade nämner avskogning / habitatdegradering som ett problem.
|
2 |
Niyama Based Taper Optimizations in Steel Alloy CastingsGorsky, Daniel A. 16 September 2011 (has links)
No description available.
|
3 |
Process development for investment casting of thin-walled components : Manufacturing of light weight componentsRaza, Mohsin January 2015 (has links)
Manufacturing processes are getting more and more complex with increasing demands of advanced and light weight engineering components, especially in aerospace industry. The global requirements on lower fuel consumption and emissions are increasing the demands in lowering weight of cast components. Ability to produce components in lower wall thickness will not only help to reduce the cost of production but also help to improve the efficiency of engineering systems resulting in lower fuel consumption and lesser environmental hazardous emissions. In order to produce thin-walled components, understanding of mechanism behind fluidity as it is effected by casting parameters is very important. Similarly, for complex components study of solidification morphology and its effects on castability is important to understand. The aim of this work was to investigate casting of thin-walled test geometries (less than 2mm) in aero-space grades of alloys. The casting trials were performed to investigate the fluidity as a function of casting parameters and filling system in thin-walled sections. Test geometries with different thickness were cast and evaluated in terms of filled area with respect to casting parameters, ı.e. casting temperature and shell preheat temperature. Different feeding systems were investigated to evaluate effects of filling mode on castability. Similarly for complex components where geometries are very organic in shape, solidification morphology effects the quality of castings. Process parameters, that effect the solidification morphology were identified and evaluated. In order to develop a relation between defect formation and process parameters, solidification behaviour was investigated using simulations and casting trials. Similarly the effect of factors that influence grain structure and flow related defects were studied. It was observed that fluidity is affected by the mode of geometry filling in investment casting process. The filling mode also have different effect on defect formation. A top-gated configuration is strongly affected by casting parameters where as a bottom-gated configuration is more stable and thus fluidity is not significantly affected by variation in casting parameters. Less porosity and flow-related defects were observed in the bottom-gated system as compared to top-gated system. In the study about casting defects as affected by process parameters, it was observed that shell thickness is important to avoid interdendritic shrinkage. It was observed that the increased shell thickness induces a steeper thermal gradient which is essential in order to minimize the width of the mushy zone. It was also observed that a slower cooling rate along with a steeper thermal gradient at the metal-mould interface not only helps to avoid shrinkage porosity but also increases fill-ability in thinner sections. The work presented here is focused on the optimization of process parameters, in order, for instance, to improve castability and reduce the casting defects in investment casting process. The work, however, does not focus on externally influencing the casting conditions or modifying the casting/manufacturing process. The future work towards PhD will be focused on externally improving the casting conditions and investigating other possible route of manufacturing for thin, complex components.
|
4 |
Optimal Design of Feeding System in Steel CastingsTavakoli, Ruhollah 20 September 2009 (has links) (PDF)
In the present study, the optimal design of feeding system in steel sand-mold castings is considered. The first part of this research includes fundamental studies on the physics of shrinkage defect formation during the casting process. The results of these studies lead to new findings on the mechanism of shrinkage defect formation, effect of melt quality on the distribution of defects within the castings and the connection between shrinkage and gases defects. The theoretical analysis of thermal criterion functions for the prediction of shrinkage defects in castings and introducing new criterion function with fewer shortcomings can be accounted as the other finding of this part. A new model was introduced in the second part of this research for the purpose of optimal design of feeding system in the shape casting processes. In this model the optimal design problem is formulated as a point-wise constrained topology optimization problem. Unlike alternative methods, the presented method does not require any predesigned feeding system as an initial guess. Using the functional analysis on the infinite-dimensional function spaces, a numerically efficient method was introduced to solve the optimal design problem in this study. By using extensive numerical experiments, capabilities and limitations of the presented method were studied in the last part of this research.
|
5 |
On Being: The Fictional Yamas and NiyamasGeisse, Elisabeth 19 December 2016 (has links)
No description available.
|
Page generated in 0.0195 seconds