The thermal formation of polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), biphenyls (PCBs), and naphthalenes (PCNs) is a major problem in waste incineration. Ideally, rather than relying on air cleaning systems and treatment techniques, their formation should be minimized or, if possible eliminated. The work presented in this thesis was conducted to obtain a deeper understanding of the thermal formation of PCDDs, PCDFs, PCBs, and PCNs during incineration using a 5 kW laboratory scale incinerator and two artificial wastes that were designed to reflect regional differences in waste composition. The first part of the thesis focuses on the validation of a recently-developed flue-gas sampling probe with enhanced cooling capabilities. Artifact formation of PCDDs and PCDFs can occur during the sampling of hot flue gases if the cooling is insufficient. The new probe was successfully used to collect samples at 700 °C without biasing the measured POP levels. The thermal formation of PCDDs, PCDFs, PCBs, and PCNs in the post-combustion zone of the incinerator was then studied by collecting flue gas samples at 400 °C, 300 °C, and 200 °C during the incineration of the two artificial wastes. Highly chlorinated POPs were formed in larger quantities when burning the waste with the higher content of metals and chlorine, which suggests that high metal levels in the waste favor the chlorination of less chlorinated POPs or otherwise facilitate the formation of highly chlorinated polyaromatics, possibly via the condensation of highly chlorinated phenols. The concentrations of these pollutants and the abundance of highly chlorinated homologues increased as the flue gas cooled. Fly ash particles play an important role in thermal POP formation by providing essential elements (carbon, chlorine, etc.) and catalytic sites. The chemical and mineralogical properties of fly ash samples were studied by X-ray diffraction (XRD), Fourier Transform Infrared (FTIR), Scanning Electron Microscopy/Energy Dispersive X-ray (SEM/EDX), and X-ray photoelectron spectroscopy (XPS) to determine their impact on thermal POP formation. Orthogonal Partial Least Squares (OPLS) modeling was used to identify correlations between the observed POP distributions and the physicochemical data. This investigation provided new insights into the impact of fly ash chemistry on thermal POP formation. In addition, the POP isomer distribution patterns generated during waste combustion were examined. These patterns are used to “fingerprint” mechanisms of POP formation. It was found that wastes containing large quantities of metals and chlorine favored the formation of highly chlorinated homologues including the very toxic 2,3,7,8-congeners. The data suggest that reducing fly ash emissions might increase the SO2 content of the flue gas and thereby suppress the Deacon process and the formation of harmful highly chlorinated aromatic species.

No description available.

Do metal particles (including particles of pure metals, alloys, metal oxides and compounds) pose a hazard or risk to human health? In the light of this question, this thesis summarizes results from research conducted on metal particles, and describes the elaboration and implementation of an in vitro test methodology to study metal release from particles through corrosion and dissolution processes in synthetic biological media relevant for human exposure through inhalation/ingestion and dermal contact. Bioaccessible metals are defined as the pool of released metals from particles that potentially could be made available for absorption by humans or other organisms. Studies of bioaccessible metals from different metal particles within this thesis have shown that the metal release process is influenced by material properties, particle specific properties, size distribution, surface area and morphology, as well as the chemistry of synthetic biological test media simulating various human exposure scenarios. The presence of metal particles in proximity to humans and the fact that metals can be released from particles to a varying extent is the hazard referred to in the title. The bioavailable metal fraction of the released metals (the fraction available for uptake/absorption by humans through different exposure routes) is usually significantly smaller than the bioaccessible pool of released metals, and is largely related to the chemical form and state of oxidation of the released metals. Chemical speciation measurements of released chromium for instance revealed chromium to be complexed to its non-available form in simulated lung fluids. Such measurements provide an indirect measure of the potential risk for adverse health effects, when performed at relevant experimental conditions. A more direct way to assess risks is to conduct toxicological in-vitro testing of metal particles, for instance on lung cell cultures relevant for human inhalation. Induced toxicity of metal particles on lung cells includes both the effect of the particles themselves and of the released metal fraction (including bioaccessible and bioavailable metals), the latter shown to be less predominant. The toxic response was clearly influenced by various experimental conditions such as sonication treatment of particles and the presence of serum proteins. Thorough characterization of metal particles assessing parameters including chemical surface composition, degree of agglomeration in solution, size distribution, surface area and morphology was performed and discussed in relation to generated results of bioaccessibility, bioavailability and induced toxicity. One important conclusion was that neither the surface composition nor the bulk composition can be used to assess the extent of metals released from chromium-based alloy particles. These findings emphasize that information on physical-chemical properties and surface characteristics of particles is essential for an in-depth understanding of metal release processes and for further use and interpretation of bioaccessibility data to assess hazard and reduce any risks induced by human exposure to metal particles. / QC 20100803