Single frame ultrasound B-mode image quality is largely governed by the ability to focus the ultrasound beam over a range in depths both in transmission and reception. By developing a comprehensive understanding of acoustic wave propagation two signal processing methods were identified for solving the transmission problem. We made use of both the impulse response using the classical point spread function (PSF) and the spatial sensitivity function (SSF) which describes the spatial distribution at a particular time. Using the angular spectrum method, an accurate analytical model was developed for the field distribution arising from a finite geometry, apodized and focused, plane piston transducer. While there is a thorough understanding of the radiated field arising from uniformly excited plane piston transducers, the focused equivalent (i.e., one that allows a continuous change in phase over the plane piston surface) is incomplete and assumes the Fresnel approximation. Our model addresses the effects of diffraction and evanescent waves without the use of the Fresnel approximation and is applicable at all near- and far-field locations in a lossless medium. The model was analyzed to identify new insights into wave propagation and compared with the Fresnel approximation and the spherically-focused, concave transducer. The piston transducer model was then extended to an attenuating and dispersive medium. After analysing existing models of power-law frequency dependent attenuation, a causal, spherical wave Green’s function was derived from the Navier-Stokes equation for a classical viscous medium. Modifications to the angular spectrum method were presented and used to analyze the radiated field of a focused, planar piston transducer. Finally, after presenting our signal processing strategy for improving imaging spatial resolution through minimization of the SSF, two signal processing methods were derived and analysed in simulation: a deconvolution technique to remove the effects of the ultrasound excitation wave and suppress additive noise from the received ultrasound signal, and a retrospective transmit focusing method that changed the response from a predefined transmit focus to an arbitrary transmit focal depth. Proof-of-concept simulations were presented using a variable number of scatterers and compared with the traditional matched filtering and envelope detection technique.

Thesis (M.S.)--West Virginia University, 2000. / Title from document title page. Document formatted into pages; contains ix, 64 p. : ill. (some col.) Includes abstract. Includes bibliographical references (p. 42-43).

Thesis (MSc)--Stellenbosch University, 2015. / ENGLISH ABSTRACT: The design optimisation of a linear oscillatory electric generator for application in freepiston Stirling engines is described in this thesis. A basic overview of free-piston Stirling engine technology is given by firstly providing a brief description of the operation of the heat engine. The applications of free-piston Stirling engines in industry are given and the proposed future applications are described. Different types of electrical machine designs from industry and academia are evaluated in a literature study. A classification structure is also proposed based on the magnetic flux variation within the designs. Based on the literature study, a transverse flux, single-phase, moving magnet, tubular topology was chosen for investigation. Athree dimensional finite element simulation was chosen as the most appropriatemethod to model the linear electrical machine. A commercial simulation package was called from a simulation script and the outputs from the finite element simulation were again used to calculate the electrical machine performance parameters using the instantaneous voltageand current values. A sequential quadratic programming algorithm was used to perform optimisation of the machine topologies, with the optimisation variables being dimensional parameters that describe the machine geometry and the goal of the optimisation to minimise the active mass of the machine, while maintaining preset minima for the output power and the efficiency. The machine was optimised for a number of different translator configurations and the different configurations were analysed and compared. It was found that a quasi-Halbach arrangement of the permanent magnets yielded the lowest overall active mass. A comparative study is also presented, where this quasi-Halbach variant is compared to a commercial machine. It was found that the linear machine design with a quasi-Halbach arrangement compares well with the commercial machine. A prototype and test bed was designed and constructed. Due to manufacuring difficulties however, the machine could not be completed in time for testing. / AFRIKAANSE OPSOMMING: Die ontwerpsoptimering van ’n lineêre ossillerende elektriese generator vir toepassing in vrysuier Stirling enjins word beskryf in hierdie tesis. ’n Basiese oorsig van vrysuier Stirling enjin tegnologie word gegee deur eerstens ’n kort beskrywing te gee van die werking van die hitte-enjin. Die aanwending van vrysuier Stirling enjins in industrie word gegee en voorgestelde toekomstige toepassings word beskryf. Verskillende tipes elektriese masjien ontwerpe vanuit die industrie en die akademie word geëvalueer in ’n literatuurstudie. ’n Klassifiseringstruktuur, gebaseer op die magnetiese vloedverandering in die ontwerpe, word ook voorgestel. ’n Transverse vloed, enkelfase, bewegende magneet, tubulêre topologie is gekies vir die ondersoek, gebaseer op die onder andere die literatuurstudie. ’n Drie-dimensionele eindige element simulasie is gekies as die mees geskikte metode om die lineêre elektriese masjien te modelleer. ’n Kommersiële simulasie pakket is deur middel van ’n simulasie skrip geroep en die uitsette vanaf die eindige element simulasie is weer gebruik om die werksverrigtingsparameters van die elektriese masjien te bereken deur gebruik te maak van die oomblikswaardes van die spanning en stroom. ’n Sekwensiële kwadratiese programmering algoritme is gebruik om optimering van die masjien topologieë te doen, met die dimensionele parameters wat die masjien geometrie beskryf as die optimeringsveranderlikes en doel van die optimering om die aktiewe massa van die masjien te minimeer, terwyl die uitsetdrywing en die benuttingsgraad by voorafgestelde minima gehou word. Die masjien is geoptimeer vir verskeie translator konfigurasies en die verskillende konfigurasies is geanaliseer en vergelyk. Dit is bevind dat ’n kwasi-Halbach skikking van die permanente magnete die laagste totale aktiewe massa gelewer het. ’n Vergelykende studie is ook aangebied, waar die kwasi-Halbach variant vergelyk is met ’n kommersiële masjien. Dit is bevind dat die lineêre masjien met die kwasi-Halbach skikking baie goed vergelyk met die kommersiële masjien. ’n Prototiepe masjien en toetsopstelling is ontwerp en aan mekaar gesit. Maar as gevolg van vervaardigbaarheids tekortkominge kon toetse op die prototiepe nie betyds gedoen word nie.

Orientador: Katia Lucchesi Cavalca / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecanica / Made available in DSpace on 2018-08-12T19:28:08Z (GMT). No. of bitstreams: 1 Daniel_GregoryBregion_M.pdf: 2663262 bytes, checksum: f7c1b338ec3a0dad168c82dc8c8d2fc2 (MD5) Previous issue date: 2008 / Resumo: Este trabalho visa analisar o comportamento dinâmico do sistema pino pistão. Por esse motivo, foi desenvolvido um modelo matemático para o mecanismo biela-manivela, considerando a influência do mancal hidrodinâmico da junção biela-pistão. As análises dinâmicas desse sistema foram realizadas utilizando dois modelos distintos. O primeiro modelo foi usado para representar o sistema quando o pino pistão está em contato com a superfície do mancal, assumindo, nesta condição, um comportamento similar aos mancais rígidos (sem folga). O segundo modelo foi empregado para representar o sistema quando o pino pistão está em lubrificação hidrodinâmica. Nesta condição, o pino pistão tem um movimento relativo à biela, o que torna este sistema um problema de múltiplos graus de liberdade. Diante disso, o primeiro modelo foi desenvolvido através da Equação de Movimento de Eksergian, sendo o segundo modelo, desenvolvido a partir do método de Lagrange. O modelo matemático de lubrificação hidrodinâmica foi introduzido com o intuito de obter resultados mais realísticos sobre o comportamento dinâmico do sistema. Este modelo de lubrificação considera as mesmas suposições básicas da teoria de lubrificação de Reynolds. A partir do modelo desenvolvido neste trabalho foram obtidas as orbitas do pino pistão, as distribuições de pressão e as velocidades e acelerações do mecanismo biela-manivela, o que permitiu realizar uma análise preliminar do comportamento dinâmico desse sistema. / Abstract: This work aims to analyze the dynamic behavior of the piston pin system. For this reason, a mathematical model for the slider-crank mechanism was developed, considering the influence of the hydrodynamic bearing of the piston-connecting rod joint. The dynamic analyses of the system applied two distinct models. The first represented the system when the piston pin was in contact with the bearing surface, assuming, in this condition, a similar behavior of rigid bearings (without clearance). The second model represented the system when the piston pin was in hydrodynamic lubrication. Under this condition, the piston pin presented a relative motion to the conrod, what turns this system into a multidegrees of freedom problem. Therefore, the first model was developed by Eksergian's Equation of Motion and the second model was developed by Lagrange method. The mathematical model of hydrodynamic lubrication was introduced to obtain more realistic results under the system's dynamic behavior. This lubrication model considers one of the basic assumptions of the Reynolds lubrication theory. From the model developed in this work were obtained the orbits of the piston pin, the pressure distributions and the velocities and accelerations of the slider-crank mechanism, what allows a preliminary analysis of the dynamic behavior of this system. / Mestrado / Mecanica dos Sólidos e Projeto Mecanico / Mestre em Engenharia Mecânica

Les balances manométriques sont utilisées en métrologie des pressions statiques.Des projets européens tel qu'Euromet 463 ont mis en évidence des écarts systématiques entreles mesures expérimentales et les calculs des paramètres nécessaires à la caractérisation desbalances de référence. La vitesse de chute du piston est l'un d'eux pourtant essentiel dans laprocédure d'étalonnage. L'objectif des travaux de thèse est l'ajustement des méthodesd'estimation de cette vitesse de chute. Cela permettra d'améliorer la caractérisation du jeuinterne de la balance, de déterminer plus précisément la section effective de ce jeu et parconséquent d'améliorer l'incertitude portant sur le coefficient de déformation, paramètre clé del'étalonnage par comparaison. Jusqu'à présent le modèle de calcul de l'écoulement du fluidedans la balance était quasi unidimensionnel. Il assimilait le jeu entre le piston et le cylindre àdeux parois parallèles. Dans cette étude, les équations de l'écoulement du flu ide sont modifiéespour évaluer l'influence du modèle dans un jeu annulaire. Les corrections dues à la vitesse dechute du piston sont également prises en compte. Les calculs des déformations des structuressont réalisés en utilisant la méthode des éléments finis. Les travaux expérimentaux portent surdes ensembles piston-cylindre 50, 200 et 1000 MPa du Laboratoire National de Métrologie etd'Essais (LNE). Une confrontation calcul-expérience est réalisée en prenant en compte lesparamètres de variabilités tels que la géométrie ou les propriétés du fluide. / The pressure balances are utilized in the metrology of the static pressure. TheEuropean project as "Euromet 463" has underlined the lack of agreement between experimentalmeasurements and calculations of the parameters necessary for the pressure balance. Thepiston fall rate is, in particular, an essential parameter in the calibration procedure. The aim ofthe thesis is the adjustment of methods for estimating the piston fall rate. This will improve thecharacterization of the gap, determine the effective area more precisely and consequentlyimprove the uncertainty on the pressure distortion coefficient, a key parameter for the calibrationby comparison. lndeed, the former quasi one-dimensional madel assimilates the gap betweenpiston and cylinder as formed by two parallel walls, which is an approximation. ln this study, theequations of the fluid flow are modified to evaluate the influence of the model in an annular gapmadel. ln addition, corrections due to the velocity of the piston wall are taken into account. Thisresearch work is applied on the piston-cylinder units 50, 200 and 1000 MPa of the Laboratoirenational de métrologie et d'essais (LNE). Taking into consideration the variability of parameterssuch as geometry or fluid properties, a comparison between the experiment and the calculationis carried out.

This diploma thesis deals with completion of the calculation FEM stress analysis of current type of CI - engine piston construction. Then it deals with design of new types of CI - engine piston construction including of their stress analysis. Analysis of advantages and disadvantages of single types of construction is made on the basis of results comparison.

Hlavní cíl této práce je vyvinout pokročilý výpočtový model dynamiky pístové skupiny. Kontakt mezi pístem a válcem je zprostředkován skrz vrstvu maziva nebo pomocí kontaktu nerovností. To vede k různým režimům mazání, tudíž k různým silovým interakcím působících na plochy kontaktní dvojice. Během řešení hydrodynamiky a kontaktu nerovností, je nutné zahrnout deformaci pístu a válce do výpočtu—přirozeně iterační proces. Jelikož požadavky na výpočtovou síť kontaktních sil a deformaci těles se liší, byl navržen robustní mapovací algoritmus. Výsledky vyvinutého výpočtového nástroje jsou experimentálně verifikovány. Pro tento účel je uskutečněno měření sekundárního pohybu pístu pomocí laserových snímačů vzdálenosti. Měření je vykonáno na experimentálním motoru s bočním vedením ventilů a průhlednou hlavou válce, aby byl přítomen kompresní tlak ve spalovací komoře. Naměřený boční pohyb pístů je znehodnocen. Proto je další analýze potrobeno pouze úhlové natočení pístů. Shoda mezi naměřenými a vypočítanými výsledky variuje pro různé části pracovního cyklu. Dobrá shoda je dosažena během komprese a expanze. Naopak výrazné rozdíly nastávají, když boční síla dosahuje nízkých hodnot: sání a výfuk. Hlavní přínos této práce je vytvoření výpočtového nástroje, který je schopný zahrnout výše popisované jevy, které mají podstatný vliv na dynamiku pístové skupiny. Bohužel to vede k dlouhým výpočtovým časům, zvláště když je zahrnuta deformace. Tento problém řeší navržený paralelní výpočet. To je založeno na paralelizaci podprogramu během vyčíslování citlivostní analýzy. Tímto způsobem je řádově redukován výpočtový čas.

The goal of the thesis was to design a piston manufactured by conventional method and subsequently adjusted one for additive manufacturing. Beside the designs, thermo-structural model was created for both pistons, considering maximal loading of the engine. Analysis evaluation showed the possibility of further application of the new technology in comparison to current one, within automotive industry.

This diploma thesis deals with solution of project automatization of manipulation with piston. On the basic theoretical knowledge about Bosch Company and terms connected with automatization in industry is tied up with detailed description of actual state of solution, which presents workplace as the thesis issue. After that follows the project of processes containing time simulations and description of variants of the solution, from which is selected the best one. The selected variant is descripted in a special chapter, where is analysed the concept of optimized workplace with its elements of automatization and its parts. Workplace is appraised by technical-economic way, where is included the project calculation of backflow. In last point is made risk analysis used for reduction of risks and increase of the workplace safety.

This Master thesis aims to increase the effectivity of the machining of pneumatic cylinders specific components. In the first chapter, the concurrent approach to the manufacture of corrosion resistant austenitic piston rod. This approach consists of the technological procedure, the analysis of the cutting tools used in the process and the cutting conditions. The machining process deals with low durability of cutting tools and the necessity of continual supervision by the operator. Therefore, an alternate design of cutting tools and cutting conditions is suggested in the next chapter. The new design has been tested in manufacture process. In the last chapter, the concurrent and the innovative approach are compared. By choosing the proper cutting tools and cutting conditions it was managed to increase the durability of cutting tools and to increase the effectivity of the whole manufacture process.