Ultra-fine grained (UFG) materials have attracted considerable interest due to the possibility of achieving simultaneous increase in strength and ductility. Effective use of these materials in engineering applications requires investigating the processing-microstructure-property inter-relations leading to a comprehensive understanding of the material behavior. Research efforts on producing UFG hexagonal close packed (hcp) materials have been limited in spite of their envisaged utilization in various technologies. The present study explores multiple UFG hcp materials to identify the general trends in their deformation behaviors, microstructural features, crystallographic texture evolutions and mechanical responses under strain path changes. UFG hcp materials, including commercial purity Ti, Ti-6Al-4V alloy and high purity Zr, were fabricated using equal channel angular extrusion (ECAE) as a severe plastic deformation (SPD) technique following various processing schedules. Several characterization methods and a polycrystal plasticity model were utilized in synergy to impart the relationships between the UFG microstructure, the texture and the post-ECAE flow behavior. Pure UFG hcp materials exhibited enhanced strength properties, making them potential substitutes for coarse-grained high strength expensive alloys. Incorporation of post-ECAE thermo-mechanical treatments was effective in further improvement of the strength and ductility levels. Strong anisotropy of the post-ECAE flow response was evident in all the materials studied. The underlying mechanisms for anisotropy were identified as texture and processing-induced microstructure. Depending on the ECAE route, the applied strain level and the specific material, the relative importance of these two mechanisms on plastic flow anisotropy varied. A viscoplastic self-consistent approach is presented as a reliable model for predicting the texture evolutions and flow behaviors of UFG hcp materials in cases where texture governs the plastic anisotropy. Regardless of the material, the initial billet texture and the extrusion conditions, ECAE of all hcp materials revealed similar texture evolutions. Accurate texture and flow behavior predictions showed that basal slip is the responsible mechanism for such texture evolution in all hcp materials independent of their axial ratio. High strength of the UFG microstructure was presented as a triggering mechanism for the activation of unexpected deformation systems, such as high temperature deformation twinning in Ti-6Al-4V and room temperature basal slip in pure Zr.

This doctoral thesis presents a modeling method fordemonstrating the behavior of inclusions and their surroundingmatrix during plastic deformation of steels. Inclusions are inescapable components of all steels. Moreknowledge about their behavior in processes such as rolling andforging is necessary for carrying out the forming processes ina more proper way so that the properties of the final productare improved. This work is focussed on deformation ofinclusions together with void formation at the inclusion-matrixinterface. The topic of the work is analyzed by differentFE-codes. The relative plasticity index is considered as an importantmeasure for describing the deformability of inclusions. Theindex could be analyzed quantitatively, enabling a deeperunderstanding of the deformation mechanisms. The workingtemperature is found to be an important process parameter. Thisis very clear when the deformation of silicate inclusions in alow-carbon steel is studied during hot rolling. Here a narrowtransition temperature region exists, meaning that theinclusion behaves as non-plastic at lower temperatures and asplastic at higher. The results are in agreement withexperiments published by other authors. Regarding void formation, the simulations have been carriedout by utilizing an interfacial debonding criterion. Thedifference in yield stress between the matrix and the inclusionis one common reason for void initiation and propagation.During large compressive deformation the evolution of voidsgoes through a sequence of shapes, from convex with two cuspsto concave with three cusps together with self-welding lines.It is concluded that the formation of voids is alwaysassociated with a large relative sliding between the inclusionand the matrix. In order to study the local behavior of the material closeto inclusions during hot rolling a mesomechanical approach isused. Uncoupled macro- and micro- models have been developed.By means of the macro-model, the stress-strain historythroughout each sub-volume of the steel is evaluated. Thestress components or velocity fields are recorded with respectto time as history data. No consideration is taken to theexistence of inclusions. The micro-model, which includes bothinclusion and steel matrix, utilizes the stress components orthe velocity fields from the macro-model as boundaryconditions. <b>Keywords</b>: Inclusion; Steel; Plastic deformation; Void;Rolling; Forging; Finite Element; Mesomechanical approach.

The unique features of the Spark plasma sintering (SPS) were used to investigate the sintering and deformation behaviour of titanium and titanium–titanium diboride composites, and to control the sintering and grain growth of ferroelectric Na0.5K0.5NbO3 (NKN) and of hydroxyapatite (HAp). In the SPS the samples experience a temperature different from that recorded by the thermocouple (pyrometer) used and this temperature difference has been estimated for Ti and NKN.   Sintering and deformation of titanium was investigated. Increasing heating rate and/or pressure shifted the sintering to lower temperatures, and the sintering and deformation rates changed when the α→β phase transition temperature was passed. Fully dense Ti/TiB2 composites were prepared. The Ti/TiB2 composites could be deformed at high temperatures, but the hardness decreased due to the formation of TiB.    The kinetic windows within which it is possible to obtain fully dense NKN and HAp ceramics and simultaneously avoid grain growth are defined. Materials have a threshold temperature above which rapid and abnormal grain growth takes place. The abnormal grain growth of NKN is due to a small shift in the stoichiometry, which in turn impairs the ferroelectric properties. Fully transparent HAp nanoceramics was prepared, and between 900 and 1050 oC elongated grains are formed, while above 1050 oC abnormal grain growth takes place.NKN samples containing grains of the sizes 0.35–0.6 µm yielded optimum ferroelectric properties, i.e. a high remanent polarization (Pr = 30 µC/cm2) and high piezoelectric constant (d33= 160 pC/N). The ferroelectric domain structure was studied, and all grains exhibited a multi-domain type of structure. / At the time of doctoral defense the following articles were unpublished and had a status as follows: Article 4: Manuscript; Article 5 : Manuscript

Plastic  deformation of tubes can be achieved in numerous ways. One of the most useful type is CNC tube bending machines which is used in many industries such as aerospace, automotive, HVAC systems and so on. It is important that all components of system should mate properly after producing and because of this bend shaping requires sensitive operation on each components to ensure regularity of production processes with high quality end-product. Thus, the CNC tube bending industry to become widespread. However it brings some troubleshooting like wrinkling, springback, breakage and ovalisation. This failures depends on geometry of the material such as bending radius, tube thickness and also friction factor between dies and the tube. Effects of all parameters should be examined before generating the theory for a best solution. Therefore, prediction of the required moment for the proper bending process with low cost and shortened production time is needed. All of these requirements can be achieved through a C++ form application program.

Ultra-fine grained (UFG) materials have attracted considerable interest due to the possibility of achieving simultaneous increase in strength and ductility. Effective use of these materials in engineering applications requires investigating the processing-microstructure-property inter-relations leading to a comprehensive understanding of the material behavior. Research efforts on producing UFG hexagonal close packed (hcp) materials have been limited in spite of their envisaged utilization in various technologies. The present study explores multiple UFG hcp materials to identify the general trends in their deformation behaviors, microstructural features, crystallographic texture evolutions and mechanical responses under strain path changes. UFG hcp materials, including commercial purity Ti, Ti-6Al-4V alloy and high purity Zr, were fabricated using equal channel angular extrusion (ECAE) as a severe plastic deformation (SPD) technique following various processing schedules. Several characterization methods and a polycrystal plasticity model were utilized in synergy to impart the relationships between the UFG microstructure, the texture and the post-ECAE flow behavior. Pure UFG hcp materials exhibited enhanced strength properties, making them potential substitutes for coarse-grained high strength expensive alloys. Incorporation of post-ECAE thermo-mechanical treatments was effective in further improvement of the strength and ductility levels. Strong anisotropy of the post-ECAE flow response was evident in all the materials studied. The underlying mechanisms for anisotropy were identified as texture and processing-induced microstructure. Depending on the ECAE route, the applied strain level and the specific material, the relative importance of these two mechanisms on plastic flow anisotropy varied. A viscoplastic self-consistent approach is presented as a reliable model for predicting the texture evolutions and flow behaviors of UFG hcp materials in cases where texture governs the plastic anisotropy. Regardless of the material, the initial billet texture and the extrusion conditions, ECAE of all hcp materials revealed similar texture evolutions. Accurate texture and flow behavior predictions showed that basal slip is the responsible mechanism for such texture evolution in all hcp materials independent of their axial ratio. High strength of the UFG microstructure was presented as a triggering mechanism for the activation of unexpected deformation systems, such as high temperature deformation twinning in Ti-6Al-4V and room temperature basal slip in pure Zr.

High Pressure Torsion (HPT) is one of the most widely used severe plastic deformation methods which enable to obtain a crack free ultra-fine grained bulk material with improved mechanical properties like increased strength and toughness. In the process, a disc shaped sample is pressed between two anvils and deformed via surface friction forces by rotating one of the anvils. The aim of this study is to nondestructively characterize the variations in the deformation uniformity of the severely deformed steel disks. Two sets of low carbon steel samples were obtained by applying the unconstrained and constrained HPT process up to 6 turns. Magnetic Barkhausen Noise (MBN) method was used in order to evaluate the samples in a nondestructive manner via a commercial device. The results of the MBN measurements were verified with those of conventional methods such as / x-ray diffraction (XRD), metallographic examination and hardness measurements. The initial stages of HPT revealed the effects of conventional plastic deformation on MBN / however with further straining, grain size refinement prevailed and caused increase in MBN signals.

Dissimilar Channel Angular Pressing (DCAP) method is an effective Severe Plastic Deformation (SPD) technique to improve the mechanical properties of sheets or strips by producing ultrafine grains. The aim of this study is to investigate the evolution of the microstructure and the improvement in mechanical properties of 6061 Al-alloy strips deformed by DCAP up to 5 passes. Mechanical properties such as hardness and strength have been observed to increase up to a certain strain level depending on the microstructural evolution. These microstructural changes were investigated by the characterization studies of XRD, SEM and TEM analysis of the DCAPed samples indicating the subgrain formation, changes in the dislocation density and dislocation behaviors.

NiTiHf alloys have attracted considerable attention as potential high temperature Shape Memory Alloy (SMA) but the instability in transformation temperatures and significant irrecoverable strain during thermal cycling under constant stress remains a major concern. The main reason for irrecoverable strain and change in transformation temperatures as a function of thermal cycling can be attributed to dislocation formation due to relatively large volume change during transformation from austenite to martensite. The formation of dislocations decreases the elastic stored energy, and during back transformation a reduced amount of strain is recovered. All these observations can be attributed to relatively soft lattice that cannot accommodate volume change by other means. We have used Equal Channel Angular Extrusion (ECAE), hot rolling and marforming to strengthen the 49.8Ni-42.2Ti-8Hf (in at. %) material and to introduce desired texture to overcome these problems in NiTiHf alloys. ECAE offers the advantage of preserving billet cross-section and the application of various routes, which give us the possibility to introduce various texture components and grain morphologies. ECAE was performed using a die of 90º tool angle and was performed at high temperatures from 500ºC up to 650ºC. All extrusions went well at these temperatures. Minor surface cracks were observed only in the material extruded at 500 °C, possibly due to the non-isothermal nature of the extrusion. It is believed that these surface cracks can be eliminated during isothermal extrusion at this temperature. This result of improved formability of NiTiHf alloy using ECAE is significant because an earlier review of the formability of NiTiHf using 50% rolling reduction concluded that the minimum temperature for rolling NiTi12%Hf alloy without cracks is 700°C. The strain level imposed during one 90° ECAE pass is equivalent to 69% rolling reduction. Subsequent to ECAE processing, a reduction in irrecoverable strain from 0.6% to 0.21% and an increase in transformation strain from 1.25% to 2.18% were observed at a load of 100 MPa as compared to the homogenized material. The present results show that the ECAE process permits the strengthening of the material by work hardening, grain size reduction, homogeneous distribution of fine precipitates, and the introduction of texture in the material. These four factors contribute in the increase of stability of the material. In this thesis I will be discussing the improvement of mechanical behavior and stability of the material achieved after various passes of ECAE.

The primary objectives of this study were: (1) to verify the effectiveness of ECAE to induce equal amounts of strain and grain refinement in bars of different cross-sectional areas, (2) to determine the effectiveness of ECAE in breaking down the as-cast macrostructure in CDA 101 Cu and in producing a homogeneous material containing micron-scale grains upon recrystallization, and (3) to determine a thermomechanical processing (TMP) schedule (from the ones examined) that produces the best microstructure in terms of grain size and uniformity. The effects of extrus ion route, levels of strain and intermediate heat treatment were investigated. To achieve the first objective, bars having square cross-sections of three different sizes, 19 mm, 25 mm and 50 mm, were processed up to eight ECAE passes through routes A, B, C and E. To achieve the second and third objectives, bars were processed up to eight ECAE passes with and without intermediate heat treatments through routes Bc, C, E and F. ECAE processing was carried out in a 90o extrusion die with sliding walls at an extrusion speed of 2.5 mm/s. Recrystallization studies were carried out on the processed material to evaluate the recrystallization behavior and thermal stability of the material. The as-worked and recrystallized materials were characterized by Vickers microhardness, optical microscopy (OM) and transmission electron microscopy (TEM). Results indicate that similar hardness values, sub-grain morphology and recrystallized grain size are generated in the three bars having different cross-sectional sizes processed through ECAE. ECAE is shown to induce uniform strain in all three billet sizes. ECAE is therefore shown to be effective in scale-up to a size of at least 50 mm, with larger billets giving better load efficiency. Results from the later parts of this study indicate that eight extrusion passes via route Bc produces the best microstructure in terms of grain size and microstructural uniformity. The routes can be arranged in the sequence Bc> E, F> C for their ability to produce a uniform recrystallized microstructure with small average grain size. Macroscopic shear bands are sometimes generated during extrusion depending upon the initial grain morphology and texture of the material.

Bulk metallic glasses (BMGs) have displayed impressive mechanical properties, but the use and dimensions of material have been limited due to critical cooling rate requirements and low ductility. The application of severe plastic deformation by equal channel angular extrusion (ECAE) for consolidation of bulk amorphous metals (BAM) and amorphous metal matrix composites (AMMC) is investigated in this dissertation. The objectives of this research are a) to better understand processing parameters which promote bonding between particles and b) to determine by what mechanisms the plasticity is enhanced in bulk amorphous metal matrix composites consolidated by ECAE. To accomplish the objectives BAM and AMMCs were produced via ECAE consolidation of Vitreloy 106a (Zr58.5Nb2.8Cu15.6Ni12.8Al10.3-wt%), ARLloy #1 (Hf71.3Cu16.2Ni7.6Ti2.2Al2.6 -wt%), and both of these amorphous alloys blended with crystalline phases of W, Cu and Ni. Novel instrumented extrusions and a host of postprocessing material characterizations were used to evaluate processing conditions and material properties. The results show that ECAE consolidation at temperatures within the supercooled liquid region gives near fully dense (>99%) and well bonded millimeter scale BAM and AMMCs. The mechanical properties of the ECAE processed BMG are comparable to cast material: σf = 1640 MPa, εf = 2.3%, E = 80 GPa for consolidated Vitreloy 106a as compared to σf = 1800 MPa, εf = 2.5%, E = 85 GPa for cast Vitreloy 106, and σf = 1660 MPa, εf = 2.0%, E = 97 GPa for ARLloy #1 as compared to σf = 2150 MPa, εf < 2.5%, E = 102 GPa for Hf52Cu17.9Ni14.6Ti5Al10. The mechanical properties of AMMCs are substandard compared to those obtained from melt-infiltrated composites due to non-ideal particle bonding conditions such as surface oxides and crystalline phase morphology and chemistry. It is demonstrated that the addition of a dispersed crystalline phase to an amorphous matrix by ECAE powder consolidation increases the plasticity of the amorphous matrix by providing locations for generation and/or arrest of adiabatic shear bands. The ability of ECAE to consolidated BAM and AMMCs with improved plasticity opens the possibility of overcoming the size and plasticity limitations of the monolithic bulk metallic glasses.