¡@¡@Because of the poly-si thin film transistor have the advantage of high mobility, it can improve the analysis for the flat plan display. Using the above advantage can combine the integrated circuit as control IC and memory on the small panel to reduce the number between the switch circuits and the outside contacts. These precise circuits must be considering the photo current¡Bthermal effects and the parasitical capacitance more due to the influence of these precise circuits is more serious than the switch circuits. In my thesis, the research of the electrical characteristics of the newest excimer laser crystallize coplane poly-si thin film transistors ,and using the device length with width is 128um/6um and 128um/16um can be extracted that the environment of the facing illumination have the photo-leakage current than none illumination about four orders, and the photo-leakage current is not consider with any gate voltage. ¡@¡@With the discussion of the capacitance, the main point of my researches is to change different conditions to extract the gate to source capacitance (Cgs). In addition, the slight carriers may effect the devices with the high mobility system on panel (SOP) technology error, the temperature must be considered. ¡@¡@We find the mobility is bigger at the environment of the temperature is 300K than the environment of the temperature is 100K when the device work in the linear region and the on current is lower at the environment of the temperature is 300K than the environment of the temperature is 100K when the device work in the saturation region. Using some references and some models as the concepts can analysis some phenomenons I refer to above.

Aluminum complexes, specifically those employing bulky ligand frameworks such as sal (sal = 2-[CH═N(2,6-iPr2-C6H3)]-4,6-tBu2-phenoxide) and alpha-diimine (alpha-diimine = [(2,6-iPr2-C6H3)N═C(Me)]2) derivatives are studied in various contexts. During ethylene polymerization with LCu(II) catalysts in the presence of methylaluminoxane (MAO), ligand (L) transfer is observed from the copper centre to the aluminum centre present in MAO. In the alpha-diimine case, an (imino-amido)AlMe2 complex is formed by alpha-diimine ligand transfer to aluminum followed by alkylation of one imino moiety in the ligand backbone. These ligand transfer products are then shown to be active as ethylene polymerization catalysts, bringing into question the role of the copper species. The (sal)AlMe2, (sal)AlMeCl and (imino-amido)AlMe2 complexes were also used as initiators in the ring-opening polymerization of epsilon-caprolactone. Polymerization was studied with and without addition of tert-butanol as a co-initiator to determine its role and necessity in the catalytic cycle. Finally, the (imino-amido)AlMe2 complex was also used as the starting complex in attempts at forming a mononuclear aluminum(I) target species. Reaction of (imino-amido)AlMe2 with excess I2 proved successful in forming the isolable precursor, (imino-amido)AlI2. Attempts at reducing (imino-amido)AlI2 with excess potassium were carried out in hopes of forming a very rare example of a mononuclear aluminum(I) species.

Bacterial biofilms are surface associated colonies that are of considerable concern and interest to industry, medicine and research. They are resistant to antibiotics, their host’s defences and are able to survive under harsh conditions. Biofilm formation in many bacterial strains are dependent on the production of a polysaccharide intercellular adhesion (PIA), a beta-(1-->6)-N-acetylglucosamine polymer. Vaccines derived from biologically isolated PIA have shown efficacy against clinically isolated strains of E. coli and pathogenic strains of S. aureus in animal models. Accordingly, chemically synthesized neoglycoconjugates based on PIA glycosides will be developed to serve as lead compounds for the development of new antibiotics as well as vaccines against biofilm dependent infections. Described in this thesis is a comprehensive study of the synthesis of PIA oligosaccharides and their deacetylated equivalents, the strategy for installing a stable linker on the free reducing oligosaccharide terminus and finally the conjugation to a model carrier protein for the development of potential neoglycoprotein vaccines.

Bacterial biofilms are surface associated colonies that are of considerable concern and interest to industry, medicine and research. They are resistant to antibiotics, their host’s defences and are able to survive under harsh conditions. Biofilm formation in many bacterial strains are dependent on the production of a polysaccharide intercellular adhesion (PIA), a beta-(1-->6)-N-acetylglucosamine polymer. Vaccines derived from biologically isolated PIA have shown efficacy against clinically isolated strains of E. coli and pathogenic strains of S. aureus in animal models. Accordingly, chemically synthesized neoglycoconjugates based on PIA glycosides will be developed to serve as lead compounds for the development of new antibiotics as well as vaccines against biofilm dependent infections. Described in this thesis is a comprehensive study of the synthesis of PIA oligosaccharides and their deacetylated equivalents, the strategy for installing a stable linker on the free reducing oligosaccharide terminus and finally the conjugation to a model carrier protein for the development of potential neoglycoprotein vaccines.

A PHA producing bacterium (strain QN271) was selected from mangrove soil samples collected from Quang Ninh province by using the Nile red dying technique. PHA accumulation in the selected bacterium strain was confirmed by transmission electron microscope. With the exception of maltose or sucrose, the bacterium strain was found to be able to synthesize PHA from various carbon sources (glucose, xylose, fructose, glycerol, and glucose plus propionate). The strain accumulated poly(3-hydroxybutyrate) from glucose, fructose, xylose, and glycerol whereas poly(3-hydroxybutyrate-co-3-hydroxyvalarate) was produced when a combination of glucose and propionate was included in the culture medium. Fructose was found to be most suitable substrate for PHA synthesis by strain QN271. PHA content of 63.3% and CDW of 6 g/L were obtained after 32 hrs of cultivation in fructose medium. / Chủng vi khuẩn có khả năng sinh tổng hợp PHA đã được phân lập từ đất rừng ngập mặn tỉnh Quảng Ninh nhờ kỹ thuật nhuộm với Nile red. Ảnh quan sát dưới kính hiển vi điện tử dẫn truyền chứng tỏ rằng chủng vi khuẩn này có khả năng tích lũy lượng lớn PHA trong tế bào. Chủng vi khuẩn tuyển chọn có khả năng sinh tổng hợp PHA từ nhiều nguồn các bon khác nhau như glucose, xylose, fructose, glucerol, glucose và propionate nhưng không có khả năng tổng hợp PHA từ maltose hoặc saccharose. Chủng vi khuẩn tuyển chọn tổng hợp poly (3-hydroxybutyrate) từ các nguồn các-bon như glucose, xylose, fructose, hay glycerol, trong khi đó poly (3-hydroxybutyrateco- 3-hydroxyvalarate) sẽ được tổng hợp khi phối hợp sử dụng hai nguồn các-bon (glucose và propionate). Fructose là nguồn các-bon tốt nhất cho chủng QN271 sinh tổng hợp PHA, khi nuôi cấy trong môi trường có fructose chủng vi khuẩn này có thể tạo ra lượng sinh khối là 6 g/L trong đó có chứa 63.3% PHA sau 32 giờ.

ABSTRACT Background: Polyunsaturated fatty acids (PUFA) are found in nuts and seeds, salad dressings and vegetable oil and are prone to oxidation during storage and food preparation. Evidence supports that consumption of oxidized lipids promotes atherosclerosis and glucose intolerance in animal models. However there is a dearth of evidence with regard to the amount of oxidized lipids consumed and its association with parameters of adiposity and glucose homeostasis in humans. Objective: The objective of this study is to estimate the amount of oxidized lipids in common foods and the oxidized lipid consumption in the US population using the data from National Health and Nutrition Examination Survey (NHANES) 2005-06. The second objective of this study is to investigate if there is an association between consumption of oxidized lipids with markers of adiposity and glucose tolerance. Methods- Foods with possible high oxidized lipid content were selected from the NHANES food frequency questionnaire. Oxidized lipid content /Peroxide Values (PV) of these foods were determined from published values in the literature. Oxidized lipid consumption was stratified into tertiles to determine the relationship between consumption of oxidized lipids and markers of adiposity. Regression analysis was used to explore to the extent to which body fat % and HOMA- IR scores could be attributed to oxidized lipid intake. Results- The estimated mean daily consumption of oxidized lipids was 0.625 meq/kg of fat for the US population. Estimated mean consumption of oxidized lipids was significantly greater in men compared to women, in children compared to adults and among African Americans compared to other races. In both men and women it was observed that the markers of adiposity like body fat%, waist circumference, triceps skinfold decreased significantly with increased consumption of oxidized lipids. However in women (below 18 years) there was a significant increase in HOMA-IR with increased consumption of oxidized lipids. Conclusion- Increased consumption of oxidized lipids is associated with decreased fat mass but increased glucose intolerance in women, but not in men.

The synthesis of arborescent poly(gamma-benzyl L-glutamate) (PBG) molecules was achieved through successive grafting reactions of linear PBG chains. These linear PBG building blocks were obtained by the ring-opening polymerization of gamma-benzyl L-glutamic acid N-carboxyanhydride initiated with n-hexylamine. Cleavage of a fraction of the benzyl ester groups on a linear PBG substrate, followed by coupling with linear PBG side chains via standard peptide coupling techniques, yielded a comb-branched or generation zero (G0) arborescent PBG. Further cycles of partial deprotection and grafting reactions led to arborescent PBG molecules of the subsequent generations (G1-G3). Molecular weights reaching over 106 were obtained for G3 arborescent PBG, while maintaining narrow molecular weight distributions (Mw/Mn ≤ 1.06) for each generation. The arborescent PBG molecules displayed α-helix to randomly coiled chain conformation changes from N,N-dimethylformamide to dimethylsulfoxide. Amphiphilic copolymers were obtained by grafting the arborescent PBG substrates randomly with side chains of either poly(glycidol acetal), poly(ethylene oxide), or poly(γ-tert-butyl L-glutamate) via the same peptide coupling techniques used to generate arborescent PBG. Copolymers were also synthesized by a chain end grafting method, whereby the linear chain segments were coupled exclusively with the chain termini of the arborescent PBG substrates. Water-soluble species were obtained by removal of the acetal and tert-butyl protecting groups from the poly(glycidol acetal) and poly(γ-tert-butyl L-glutamate) side chains, respectively, while the copolymers with poly(ethylene oxide) side chains did not require further modifications. Dynamic light scattering (DLS) measurements on the arborescent copolymers in aqueous solutions revealed that unimolecular micelles were the dominant species for the chain end grafted arborescent copolymers, whereas the randomly grafted arborescent copolymers were either insoluble or displayed significant aggregation. The synthesis of arborescent copolymers with PBG cores was also achieved through “click” chemistry, using the copper-catalyzed azide-alkyne Huisgen cycloaddition (CuAAC) reaction. To that end, polyglycidol, poly(ethylene oxide), and poly(2-trimethylsilylethyl acrylate) chains terminally functionalized with azide groups were grafted onto either randomly or chain end alkyne-functionalized arborescent PBG substrates. DLS analysis revealed solubility trends similar to the arborescent copolymers obtained by the peptide coupling method. The CuAAC reaction enables the incorporation of a broader range of polymers into arborescent copolymer structures derived from PBG substrates.

Poly(A)-specific ribonuclease (PARN) is a deadenylase that degrades the poly(A) tail of eukaryotic mRNA. PARN also interacts with the 5’-cap structure of the mRNA. The binding of the cap structure enhances the deadenylation rate. PARN has previously been described as a dimer. We have studied PARN with size exclusion chromatography to investigate the oligomeric composition and revealed oligomeric compositions of PARN that are larger than dimeric PARN. Deadenylation assays have been used to measure the cap stimulated activity of PARN. The deadenylation assays showed that the cap stimulated activity of PARN correlated with the abundance of oligomers corresponding in size to tetrameric PARN. We present a model for tetrameric PARN and propose a mechanistic model for how the cap stimulates PARN mediated deadenylation.

Aluminum complexes, specifically those employing bulky ligand frameworks such as sal (sal = 2-[CH═N(2,6-iPr2-C6H3)]-4,6-tBu2-phenoxide) and alpha-diimine (alpha-diimine = [(2,6-iPr2-C6H3)N═C(Me)]2) derivatives are studied in various contexts. During ethylene polymerization with LCu(II) catalysts in the presence of methylaluminoxane (MAO), ligand (L) transfer is observed from the copper centre to the aluminum centre present in MAO. In the alpha-diimine case, an (imino-amido)AlMe2 complex is formed by alpha-diimine ligand transfer to aluminum followed by alkylation of one imino moiety in the ligand backbone. These ligand transfer products are then shown to be active as ethylene polymerization catalysts, bringing into question the role of the copper species. The (sal)AlMe2, (sal)AlMeCl and (imino-amido)AlMe2 complexes were also used as initiators in the ring-opening polymerization of epsilon-caprolactone. Polymerization was studied with and without addition of tert-butanol as a co-initiator to determine its role and necessity in the catalytic cycle. Finally, the (imino-amido)AlMe2 complex was also used as the starting complex in attempts at forming a mononuclear aluminum(I) target species. Reaction of (imino-amido)AlMe2 with excess I2 proved successful in forming the isolable precursor, (imino-amido)AlI2. Attempts at reducing (imino-amido)AlI2 with excess potassium were carried out in hopes of forming a very rare example of a mononuclear aluminum(I) species.

Poly(butylene succinate) (PBSu) and two poly(butylene succinate-co-propylene succinate)s (PBPSu 95/5 and PBPSu 90/10) were synthesized via the direct polycondensation reaction. The copolyesters were characterized as having 7.0 and 11.5 mol% propylene succinate (PS) units, respectively, by 1H NMR. Copolyesters were characterized as random, based on 13C NMR spectra. They were fully investigated during nonisothermal crystallization and thermal degradation through various approaches in this study. A differential scanning calorimeter (DSC) and a polarized light microscope (PLM) adopted to study the nonisothermal crystallization of these polyesters at a cooling rate of 1, 2, 3, 5, 6 and 10 ºC/min. Morphologies and the isothermal growth rates of spherulites under PLM experiments were monitored and obtained by curve-fitting, respectively. These continuous rate data were analyzed with the Lauritzen-Hoffman equation. A transition of regime II ¡÷ III was found at 95.6, 84.4, and 77.3 ºC for PBSu, PBPSu 95/5, and PBPSu 90/10, respectively. DSC exothermic curves show that all of the nonisothermal crystallization occurred in regime III. DSC data were analyzed using modified Avrami, Ozawa, Mo, Friedman and Vyazovkin equations. Ozawa equation does not accurately describe the nonisothermal crystallization kinetics of this polyester because part of the crystallization is secondary crystallization. All the results of PLM and DSC measurements indicate that incorporation of minor PS units into PBSu markedly inhibits the crystallization of the resulting polymer. The melting behavior of nonisothermally crystallized samples presents a continuous melting¡Vrecrystallization¡Vremelting process. Additionally, three absorption bands during the nonisothermal crystallization were identified for PBSu and two PBPSu copolyesters, namely, 916, 955, 1045 cm-1 in the attenuated total reflectance FTIR spectra. Thermogravimetric analysis (TGA)-FTIR was heated at 5 ºC/min under N2 to monitor the degradation products of these three polyesters. FTIR spectra revealed that the major products were anhydrides, which were obtained following two cyclic intramolecular degradation mechanisms by breaking the weak O-CH2 bonds around a succinate group. Thermal stability at heating rates of 1, 3, 5, and 10 ºC/min under N2 was investigated using TGA. The model-free methods of Friedman and Ozawa equations are useful for studying the activation energy of degradation in each period of mass loss. The results reveal that the random incorporation of minor PS units into PBSu did not markedly affect their thermal resistance. Two model-fitting mechanisms were used to determine the loss mass function f(£\), the activation energy and the associated mechanism. The mechanism of autocatalysis nth-order, with f(£\)=£\m(1-£\)n, fitted the experimental data much more closely than did the nth-order mechanism given by f(£\)=(1-£\)n. The obtained activation energy was used to estimate the failure temperature (Tf). The values of Tf for a mass loss of 5% and an endurance time of 60,000 hr are 160.7, 155.5, and 159.3 ºC for PBSu and two the copolyesters, respectively.