Thesis (Ph. D.)--West Virginia University, 2005. / Title from document title page. Document formatted into pages; contains x, 165 p. : ill. Includes abstract. Includes bibliographical references (p. 65-71).

Thesis (M.S.)--University of Missouri-Columbia, 2004. / Typescript. Includes bibliographical references (leaves 58-63). Also available on the Internet.

There are a number of inherent problems associated with the analysis of polycyclic aromatic compounds (PAC) in airborne particulate matter. The compounds of interest constitute a very small fraction of the total sample, but consist of hundreds of different components. Therefore, analytical techniques with very high resolving power are required. To try to address these problems, methods have been developed and improved to isolate, and subsequently profile, and identify the PAC present in typical airborne particulate samples. Since no single chromatographic technique can provide the desired resolution, a multi-stage clean-up scheme was required prior to analysis. Two methods were investigated in this study. Both methods used a Soxhlet extraction followed by fractionation using an adsorption chromatography step (silica or alumina) and Sephadex LH-20 to isolate the PAC fraction from the other organic constituents. Another problem associated with the analysis of PAC in airborne particulate matter was because of the method of sample collection. It was believed that there were changes in the chemical composition of the particulate and hence the PAC, during sample collection using a Hi-Vol sampler. Artifacts were being formed by reaction of gaseous pollutants with the particulate collected on the filter. An experiment was established to show that the addition of a denuder bundle to a Hi-Vol sampler could reduce this artifact formation during sampling by removing the reactive gases prior to the surface of the filter. The value of the denuder bundle was evaluated by comparison of the PAC from the denuder Hi-Vol with a standard Hi-Vol. Normal-phase HPLC coupled with mass spectrometry was shown to be a good method to compare the PAC in these samples. Some differences between standard and denuder Hi-Vol samples were observed in laboratory experiments, while the results from field sampling were inconclusive. The use of a parallel column gas chromatography-mass spectrometry (GC-MS) (also called third order chromatography) technique was investigated to determine its viability for the identification of the diverse range of PAC present in environmental samples. The PAC . in the NBS urban dust sample (SRM 1649) was analyzed to evaluate the method. To aid in data processing, a semi-automated peak detection routine has been developed. This routine used programs to aid in the data processing by simplifying peak detection and allow calculation of the retention indices of the components. Using the information supplied by the retention indices and the mass spectra, a data base was developed that was applied to a typical airborne particulate sample. / Thesis / Doctor of Philosophy (PhD)

Thesis (Ph. D.)--University of Nevada, Reno, 2006. / "August, 2006." Includes bibliographical references. Online version available on the World Wide Web.

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第20392号 / 工博第4329号 / 新制||工||1671(附属図書館) / 京都大学大学院工学研究科物質エネルギー化学専攻 / (主査)教授 村田 靖次郎, 教授 近藤 輝幸, 教授 小澤 文幸 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

In 1933, benzo[a]pyrene, a hydrocarbon, which was and still is of very great importance for cancer research, was isolated from coal tar and also was synthesized. In recent years more than 450 synthetic compounds have been found to be carcinogenic, and more than 200 are polycyclic aromatic hydrocarbons, their derivatives and analogues. Recently a new polynuclear hydrocarbon, a seven ring compound naphtho[2,1-a]perylene was synthesized in This Laboratory Physiological tests have revealed this compound to be a potent carcinogen. This experience has prompted a new initiative to prepare a number of related compounds of this type in order to bring further insight to the relation between chemical structure and the mechanism of physiological activity. During the synthesis of the four new seven fused aromatic ring systems and a new eight fused aromatic ring system, several modifications and improvement of existing synthetic procedures were made. A recently published modification of the Rosenmund-von Braun method of nitrile synthesis was successfully applied to the preparation of 2-(2-naphthylmethyl)benzonitrile. It was found that 2-(2-naphthylmethyl)phenyl-1-naphthyl ketone and 2-(2-naphthylmethyl)phenyl-2-naphthyl ketone could be prepared by the reaction of a Grignard reagent with a nitrile as well as by the inverse addition of a Grignard reagent to the appropriate acid chlorides. The alumina cyclodehydrogenation procedure was confirmed to be the, only method of synthesis that yields 12-(1-naphthyl)-benz[a]anthracene from its precursor ketone. The yield of 12-(2-naphthyl)benz[a]anthracene was increased from 61% to 83% when anhydrous hydrogen fluoride was used in place of 48% hydrogen bromide and glacial acidic acid as the cyclodehydration media of the precursor ketone. A new cyclodehydrogenation procedure was developed. This procedure, which employs a mixture of aluminum chloride-stannic chloride and alumina, was used to prepare a new hydrocarbon, naphtho[l,2-a]-perylene. An aluminum chloride-sodium chloride melt permeated with carbon dioxide was successfully employed in the preparation of naphtho[2,2-1]benzo- (a]pyrene, naphtho(l,2-l]benzo[a]pyrene, and naphtho- (2,3-1]benzo[a]pyrene. It was shown that high temperature gas chromatography with ionization detectors can be used with success to analyze all of the above discussed ketones, benz[a]anthracenes as well as the new perylene and pyrenes. Additional support of the validity of the. structures of naphtho[1,2-a]perylene and naphtho- [2,1-1]benzo[a]pyrene was provided when the cyclodehydrogenation of these hydrocarbons yielded one and the same product, naphtho[l,7,8-efg]anthanthrene. It was observed that the correlation between color and structure of the newly prepared hydrocarbons follows the principles of annelation. When the ultraviolet and visible spectra peak frequencies were compared it was found that the values and positions of the peaks follow the principles of the annelation method. The examination of the infrared absorption spectra revealed that naphtho[l,2-a]perylene, naphtho[2,1l-1]benzo[a]pyrene, naphtho[1,2-1]benzo[a]-pyrene, and naphtho[2,3-1]benzo[a]pyrene exhibited Peaks at all four, "solo," "duo," "trio," and "quartet", carbon-hydrogen vibration regions, but as expected naphtho[1,7,8-efg]anthanthrene had the "quartet" carbon-hydrogen peak missing between 770 and 755 cm. which further substantiated the validity of the naphtho[1,7,8-efg]anthanthrene structure. The TNF molecular adducts of the five newly prepared compounds, naphtho[1,2-a]perylene, naphtho- [2,1-1]benzo[a]pyrene, naphtho1l,2-1]benzo[a]pyrene, naphtho[2,3-1]benzo[a]pyrene, and naphtho[1,7,8-efg]-anthanthrene were prepared and their melting points recorded. In order to ascertain the structures of the naphtho[1,2-a]perylene and the naphtho[1,2-l]benzo[a]-pyrene obtained from the cyclodehydrogenation of 12-(1-naphthyl)benz[a]anthracene and 12-(2-naphthyl)-benz[a]anthracene, respectively, other routes of synthesis were undertaken. The hydrocarbon, 11-(1-naphthyl)benz[a]anthracene, was prepared by the reaction of 1-naphthylmagnesium bromide with 11-keto-5,6,8,9,10,11-hexahydrobenz[a]- anthracene which on distillation under reduced pressure gave 11-(1-naphthyl)-5,6,8,9-tetrahydrobenz[a]anthracene and on aromatization yielded 11-(1-naphthyl)benz[a]-anthracene. When 1-naphthyl magnesium bromide was allowed to react with the 11-keto-8,9,10,11-tetrahydrobenz[a]anthracene, 11-(1-naphthyl)-8,9~dihydrobenz[a]anthracene was obtained when distilled under reduced pressure. This, likewise, gave 11-(1-naphthyl)- benz[a]anthracene on aromatization. Naphtho[1,2-a]perylene was synthesized unequivocally from 11-(1-naphthyl)benz[a]anthracene via a cyclodehydrogenation reaction. The hydrocarbon, 1-(1-naphthyl)-1,2,3,4-tetrahydrobenz[a]anthracene, was prepared by the reaction of 1-naphthylmagnesium bromide with 1-keto-1,2,3,4- tetrahydrobenz[a]anthracene. On distillation under reduced pressure 1-(1-naphthyl)-1,2,3,4-tetrahydrobenz[a]anthracene was obtained. Under the conditions of an aromatization procedure, naphtho[1,2-1]benzo[a]-pyrene was obtained. The hydrocarbons 11-(1l-naphthyl)-5,6,8,9-tetrahydrobenz[a]anthracene, 11-(1-naphthyl)-8,9-dihydrobenz[a]anthracene, 11-(1-naphthyl)benz[a]-anthracene, 1-(1-naphthyl)-1,2,3,4-tetrahydrobenz[a]anthracene are additional new compounds. / Ph. D.

The process of C. K. Bradsher for preparing mesosubstituted anthracene and 1,2-benzanthracene derivatives has been widely extended. The purpose of this research was to extend this process to the thiophene series, in addition to continuing some work on the 9-(dimethyl)- phenylanthracene series and some newly developed l,2-dimethyl-10-phenyl)-anthracene series. 2'-Thienyl-2-benzylbenzophenone was prepared and cyclized to 9-(2-thienyl)-anthracene by the conventional methods in good yields. 3'-Thienyl-2-benzylbenzophenone was prepared in a different way, indirect and tedious. Thiophene was iodinated to tetraiodothiophene and tetraiodothiophene was reduced with aluminum-amalgam to 3-iodothiophene. 3-Thienylmagnesiumiodide was prepared by the entrainment technique and condensed with 2-cyanodiphenylmethane to 3'-thienyl-2-benzylbenzophenone. This ketone was cyclized to 9-(3'-thienyl)-anthracene by the standard acid mixture. 2-(1-Naphthylmethyl)-phenyl-2-thienylketimine formed from the condensation between 2-(1'-naphthylmethyl)- benzonitrile and 2-thienylmagnesiumbromide resisted hydrolysis to the corresponding ketone but cyclized quantitatively to 10-(2-thienyl)-l,2-benzanthracene. Following the classical Bradsher process, the reaction between 2-thienylmagnesiumbromide and o-chlorobenzaldehyde was unsuccessful because the hydrol formed was so reactive that it polymerized rapidly and ended up with tars. A cross-condensation reaction between 2-ethynylmagnesium bromide and o-chlorobenzylchloride was utilized to give the expected 2-(2'-chlorobenzyl)- thiophene in one step. This new procedure has been widely extended to the other series. It is preferred to. the conventional Bradsher process and the Friedel-Crafts method in terms of time, chemicals, and unequivocal products formed. 2-(2'-Chlorobenzyl)-thiophene so formed by the new procedure was converted by von Braun reaction to the corresponding nitrile and the nitrile was allowed to react with phenylmagnesiumbromide to give 2-(2-thienylmethyl)-benzophenone. The above ketone was cyclized almost quantitatively to 4-phenyl-thiophanthrene. The thiophene-containing ketones prepared in this research are very viscous oils. In order to have crystalline derivatives for identification purposes these ketones were oxidized to the corresponding diketones. 2-Thienyl-2-benzylbenzophenone and 2-(2'-thienylmethyl)- benzophenone gave the identical diketone, 2-benzoyl-2'- thienyl-benzophenone. 3 1 -Thienyl-2-benzylbenzophenone was oxidized to anthraquinone by using 25% sulfuric .acid, acetic acid and sodium dichromate. The formation of anthraquinone indicates that the monoketone cyclized first and then split off the thiophene ring. Apparently, the 3-thienyl group is more susceptible to oxidation than the 2’-thienyl group. A study of the oxidation of anthracene derivatives for structure proof was made using 9-phenylanthracene as a model compound. It was oxidized to 10-phenyl-10-hydroxyanthrone which resisted further oxidation to anthraquinone. It is obvious that the tertiary alcohol system stabilized the phenyl ring. In continuing the work on the 9-(dimethyl)-phenylanthracene series, the yields of three ketimine salts and one ketone were improved. Satisfactory analytical data was obtained for 2’,6’-dimethyl-2-benzylbenzophenone. In an attempt to overcome the steric effects offered by 2,6-ortho groups, 2-(2',3'-dimethylbenzyl)-benzonitrile was prepared. The starting material for this series, l-bromo-2,3-dimethylbenzene has been prepared in 47% yield by diazotization in comparison with the previous yield of 30%. / Doctor of Philosophy

Experimental mole fraction solubilities of benzil, thianthrene, trans-stilbene, thioxanthen-9-one, diphenyl sulfone and dibenzothiophene sulfone are determined in pure noncomplexing and complexing solvents. Predicted solubility values are calculated for benzil, thianthrene, trans-stilbene and thioxanthen-9-one using expressions derived from Mobile Order theory. Large deviations between experimental and predicted solubilities in alcohol solvents exist, therefore optimized solute - solvent association constants are determined. Previously measured thianthrene solubilities in five binary alkane + cyclohexane solvent mixtures are compared with values predicted from Mobile Order theory using the measured solubility in each of the pure solvents as input parameters. The experimental mole fraction solubility of benzil in eight binary alcohol + 1-octanol solvent mixtures are also measured and compared with predicted values.

Microbial biodegradation is the primary mechanism by which petrogenic hydrocarbons (PHCs) are removed from the environment. Though hydrocarbon biodegradation is widely studied in marine systems, knowledge of how it occurs in freshwater systems is still lacking. The Peace-Athabasca Delta (PAD), located in northeastern Alberta, is an ideal location to study microbial hydrocarbon degradation since it has a long history of exposure to PHCs. What’s more, these PHCs are predominately sourced from bituminous deposits and are therefore relevant to the Canadian Oil Sands Industry. This thesis investigated the genetic potential for hydrocarbon degradation of PHCs via metagenomic reconstruction of microbial communities in lakes of the Peace and Athabasca Deltas, as well as reference lakes in the nearby boreal uplands. In order to properly evaluate the microbial community and its potential for hydrocarbon degradation, a comprehensive analysis of PHCs (including n-alkanes, polycyclic aromatic compounds (PACs), and petroleum biomarkers of terpanes, hopanes, and steranes) was performed. PHC analysis showed that n-alkanes in lake sediments from all three regions were highly similar and predominately biogenic, while PAC composition was significantly different in each region. Restricted-drainage lakes of the Athabasca Delta had the highest concentrations of PACs from petrogenic sources. Closed-drainage lakes in the Peace Delta had lower concentrations of PACs that likely originated from a mixture of pyrogenic and petrogenic sources. Closed-drainage lakes in the boreal upland region had the lowest concentrations of PACs likely sourced from pyrogenic wood combustion with traces of petrogenic PACs, possibly from atmospheric deposition of dust. Petroleum biomarkers of terpanes, hopanes, and steranes were successfully used to identify the long-range fluvial, and possibly atmospheric, transport of bituminous compounds more than one hundred kilometers from their potential source. This validates the future use of these biomarkers in environmental forensics. Microbial communities in all three regions under study were highly diverse, and their composition was significantly different in both sediment and water. Targeted gene analysis identified a total of 3885 genes involved in the degradation of n-alkanes and PACs in sediment and water. The results show that organic carbon, nitrogen, and sulfur content, as well as PAC and short-chain alkane concentrations were important chemical predictors of change in degradation gene composition. Furthermore, genes for anaerobic degradation of PHCs were identified in syntrophic bacteria, methanogens, nitrate and sulfate reducers, demonstrating the potential for syntrophic hydrocarbon degradation in PAD lakes. Though this thesis confirms the genetic potential for hydrocarbon degradation in PAD and boreal upland lakes, further research is necessary to determine whether these microbial communities can actively degrade the PHCs present in these lakes.

The field of organic electronics has received much attention over the last few years, and engineering of organic crystals to grow with pi-electron systems arranged in a face-to-face motif has been shown to be beneficial in electronic devices. The effects of combining aromatic and perfluorinated aromatic derivatives have shown that the intramolecular stacking pattern can be changed from an edge-to-face arrangement to that of a face-to-face motif. Before the work described herein, there were no reported studies of the supramolecular behavior of fused polycyclic aromatic compounds with partial peripheral fluorination, inducing the desired face-to-face behavior. This is the main focus of the thesis. Furthermore, by exploiting the interactions between the fluorinated and non-fluorinated faces of the molecule, columnar liquid crystalline behavior can be achieved through variations of the alkyl substituents on the molecule.