Single wavelength ellipsometry measurements at Brewster's angle provide a powerful technique for characterizing ultrathin polymeric films. By conducting the experiments in different ambient media, multiple incident media (MIM) ellipsometry, simultaneous determinations of a film's thickness and refractive index are possible. Poly(tert-butyl acrylate) (PtBA) films serve as a model system for the simultaneous determination of thickness and refractive index (1.45 at 632 nm). Thickness measurements on films of variable thickness agree with X-ray reflectivity results. The method is also applicable to spincoated films where refractive indices of PtBA, polystyrene and poly(methyl methacrylate) are found to agree with literature values within experimental error. Likewise, MIM ellipsometry is utilized to simultaneously obtain the refractive indices and thicknesses of thin films of trimethylsilylcellulose (TMSC), regenerated cellulose, and cellulose nanocrystals where Langmuir-Blodgett (LB) films of TMSC serve as a model system. Ellipsometry measurements not only provide thickness and optical constants of thin films, but can also detect thermally induced structural changes like surface glass transition temperatures (Tg) and layer deformation in LB-films. Understanding the thermal properties of the polymer thin films is crucial for designing nanoscale coatings, where thermal properties are expected to differ from their corresponding bulk properties because of greater fractional free volume in thin films and residual stresses that remain from film preparation. Polyhedral oligomeric silsesquioxane (POSS) derivatives may be useful as a nanofiller in nanocomposite formulations to enhance thermal properties. As a model system, thin films of trisilanolphenyl-POSS (TPP) and two different molar mass PtBA were prepared as blends by Y-type Langmuir-Blodgett film deposition. For comparison, bulk blends were prepared by solution casting and the samples were characterized via differential scanning calorimetry (DSC). Our observations show that surface Tg is depressed relative to bulk Tg and that magnitude of depression is molar mass dependent for pure PtBA films. By adding TPP as a nanofiller both bulk and surface Tg increase. Whereas, bulk Tg shows comparable increases for both molar masses, the increase in surface Tg for higher molar mass PtBA is greater than for lower molar mass PtBA. These studies show that POSS can serve as a model nanofiller for controlling Tg in nanoscale coatings. / Ph. D.

Thin film bilayers and blends composed of polymers and nanoparticles are increasingly important for technological applications that range from space survivable coatings to novel drug delivery systems. Dewetting or spontaneous hole formation in amorphous polymer films and phase separation in multicomponent polymer films can hinder the stability of these systems at elevated temperatures. Hence, fundamental understanding of dewetting and phase separation in polymer/nanoparticle bilayer and blend films is crucial for controlling transport and thermomechanical properties and surface morphologies of these systems. This dissertation provides studies on morphological evolution driven by phase separation and/or dewetting in model polymer/nanoparticle thin film bilayers and blends at elevated temperatures. Morphological evolution in dewetting bilayers of poly(t-butyl acrylate) (PtBA) or polystyrene (PS) and a polyhedral oligomeric silsesquioxane (POSS), trisilanolphenyl-POSS (TPP) is explored at elevated temperatures. The results demonstrate unique dewetting morphologies in both PtBA/TPP and PS/TPP bilayers that are significantly different from those typically observed in dewetting polymer/polymer bilayers. Upon annealing the PtBA/TPP bilayers at 95°C, a two-step dewetting process is observed. PtBA immediately diffuses into the upper TPP layer leading to hole formation and subsequently the holes merge to form interconnected rim structures in the upper TPP layer. Dewetting of both the TPP and PtBA layers at longer annealing times leads to the evolution of scattered holes containing TPP-rich, fractal aggregates. The fractal dimensions of the TPP-rich, fractal aggregates are ~2.2 suggesting fractal pattern formation via cluster-cluster aggregation. Dewetting in PS/TPP bilayers also proceeds via a two-step process; however, the observed dewetting morphologies are dramatically different from those observed in PtBA/TPP bilayers. Cracks immediately form in the upper TPP layer during annealing of PS/TPP bilayers at 200°C. With increasing annealing times, the cracks in the TPP layer act as nucleation sites for dewetting and aggregation of the TPP layer and subsequent dewetting of the underlying PS layer. Complete dewetting of both the TPP and PS layers results in the formation of TPP encapsulated PS droplets. Phase separation in PtBA/TPP thin film blends is investigated as functions of annealing temperature and time. The PtBA/TPP thin film blend system exhibits an upper critical solution temperature (LCST) phase diagram with a critical composition and temperature of 60 wt% PtBA and ~70°C, respectively. Spinodal decomposition (SD) is observed for 60 wt% PtBA blend films and off-critical SD is seen for 58 and 62 wt% PtBA blend films. The temporal evolution of SD in 60 wt% PtBA blend films is also explored. Power law scaling for the characteristic wavevector with time (q ~ t^n with n = -1/4 to -1/3) during the early stages of phase separation yields to domain pinning at the later stages for films annealed at 75, 85, and 95°C. In contrast, domain growth is instantly pinned for films annealed at 105°C. Our work provides an important first step towards understanding how nanoparticles affect polymer thin film stability and this knowledge may be utilized to fabricate surfaces with tunable morphologies via controlled dewetting and/or phase separation. / Ph. D.

For over a century, Langmuir films have served as excellent two-dimensional model systems for studying the conformation and ordering of amphiphilic molecules at the air/water (A/W) interface. With the equipment of Wilhelmy plate technique, Brewster angle microscopy (BAM), and surface light scattering (SLS), the interfacial phase and rheological behavior of Langmuir films can be investigated. In this dissertation, these techniques are employed to examine Langmuir films of polyhedral oligomeric silsesquioxane (POSS), polymer blends, and magnetic nanoparticles (MNPs). In a first time, SLS is employed to study POSS molecules. The interfacial rheological properties of trisilanolisobutyl-POSS (TiBuP) indicate that TiBuP forms a viscoelastic Langmuir film that is almost perfectly elastic in the monolayer state with a maximum dynamic dilational elasticity of around 50 mNâ m-1 prior to film collapse. This result suggests that TiBuP can serve as model nanofiller with polymers. As an interesting next step, blends of TiBuP and polydimethylsiloxane (PDMS) with different compositions are examined via surface pressure (surface pressureâ surface area occupied per molecule (A) isotherms and SLS. The results show that TiBuP, with its attendant water, serves as a plasticizer and lowers the dilational modulus of the films at low surface pressure. As surface pressure increases, composition dependent behavior occurs. Around the collapse pressure of PDMS, the TiBuP component is able to form networks at the A/W interface as PDMS collapse into the upper layer. Blends of non-amphiphilic octaisobutyl-POSS (OiBuP) and PDMS are also studied as an interesting comparison to TiBuP/PDMS blends. In these blends, OiBuP serves as a filler and reinforces the blends prior to the collapse of PDMS by forming "bridge" structure on top of PDMS monolayer. However, OiBuP is non-amphiphilic and fails to anchor PDMS chains to the A/W interface. Hence, OiBuP/PDMS blends exhibit negligible dilational viscoelasticity after the collapse of PDMS. Furthermore, the phase behavior of PDMS blended with a trisilanol-POSS derivative containing different substituents, trisilanolcyclopentyl-POSS (TCpP), is also investigated via the Wilhelmy plate technique and BAM. These TCpP/PDMS blends exhibit dramatically different phase behavior and morphological features from previously studied POSS/PDMS blends, showing that the organic substituents on trisilanol-POSS have considerable impact on the phase behavior of POSS/PDMS blends. The interfacial rheological behavior of tricarboxylic acid terminated PDMS (PDMS-Stabilizer) and PDMS stabilized MNPs are investigated and compared with "regular" PDMS containing non-polar end groups. The tricarboxylic acid end group of the PDMS-Stabilizer leads to a different collapse mechanism. The PDMS stabilized MNPs exhibit viscoelastic behavior that is similar to PDMS showing all the tricarboxylic acid end groups are bound to the magnetite cores. Studying the interfacial behavior of different Langmuir films at the A/W interface provides us insight into the impact of molecule-molecule and molecule-subphase interactions on film morphology and rheology. These results are able to serve as important guides for designing surface films with preferred morphological and mechanical properties. / Ph. D.

Polyhedral oligomeric silsesquioxanes (POSS) have attracted substantial academic interest for many years as hybrid materials and nanofillers for controlling thermal and mechanical properties, and providing thermal and chemical resistance while retaining ease of processing. A natural extension of these studies has been POSS-based amphiphiles and thin film coatings. Studies at the air/water (A/W) interface have shown that trisilanol-POSS derivatives are amphiphilic and form uniform Langmuir films, whereas closed-cage POSS derivatives are hydrophobic and aggregate. In previous work, a triester (POSS-triester) and a triacid (POSS-triacid) were synthesized from PSS-(3-hydroxypropyl)-heptaisobutyl (POSS-OH) and Weisocyanate and fully characterized by surface pressure – area per molecule (Π-A) isotherm and Brewster angle microscopy (BAM) studies at the A/W interface. The results indicated that POSS-triester is surface active forming a liquid expanded (LE) monolayer, whereas POSS-triacid forms a liquid condensed (LC) monolayer that is only weakly affected by pH. A face-on conformation was proposed and examined to understand the packing of POSS-based amphiphilic molecules at the A/W interface. The face-on/vertex-on comparison is rarely discussed for Langmuir monolayers at the A/W interface. In this thesis, three other POSS-based esters were synthesized from POSS-OH and aminopropylisobutyl-POSS (POSS-NH₂) using Weisocyanate and a similar isocyanate containing two tert-butyl protected carboxylic acids. The synthesized materials are characterized by Π-A isotherm and BAM. For POSS-OH based diester (PAlDE) and POSS-NH2 based diester (PAmDE), LE/LC phase transitions were observed in Π-A isotherms over part of the experimentally accessible temperature range and were attributed to a change from a vertex-on to face-on conformation. Apparent BAM images confirmed LC islands coexisted with the LE phase. The experimentally observed dynamic estimates of the critical temperatures (Tc) were estimated from a two-dimensional Clausius-Clapeyron analysis and were consistent with the temperature dependence of the Π-A isotherms. These LE/LC phase transitions are the first observed for POSS amphiphiles. / Ph. D.

Polyhedral oligomeric silsesquioxanes (POSS) have attracted substantial academic interest for many years as hybrid materials and nanofillers for controlling thermal and mechanical properties, and for providing thermal and chemical resistance while retaining ease of processing. A natural extension of these studies has been working on POSS-based amphiphiles and thin film coatings. Studies at the air/water (A/W) interface have shown that trisilanol-POSS derivatives are amphiphilic and form uniform Langmuir films, whereas closed-cage POSS derivatives are hydrophobic and aggregate. In this study, two novel POSS derivatives were synthesized from PSS-(3-hydroxypropyl)-heptaisobutyl substituted (POSS-OH) and completely characterized. Weisocyanate reacted with POSS-OH, and a POSS-based triester (POSS-triester) was obtained. Trifluoroacidolysis of the POSS-triester at room temperature afforded the corresponding triacid (POSS-triacid). Purified POSS-OH, POSS-triester, and POSS-triacid were studied by using surface pressure - area per molecule (? -A) isotherms as well as Brewster angle microscopy (BAM) at the air/water (A/W) interface. Compared with previous work on trisilanol-POSS derivatives, the results indicated that POSS-triester was surface active and formed a liquid-expanded (LE) monolayer. In contrast, POSS-triacid monolayers were more condensed (LC) and were not dramatically affected by changes in pH. Results for the lift-off areas (Alift-off), limiting areas (A0), collapse areas (Ac), and collapse pressures (? c) of POSS-OH, POSS-triester, and POSS-triacid were compared to trisilanolisobutyl-POSS (TiBP) and were interpreted in terms of possible molecular conformations. Whereas, TiBP has been hypothesized to exist in a vertex-on conformation, POSS-OH and POSS-triacid packing at the A/W interface was consistent with face-on conformations. For POSS-triester, the isotherm was consistent with a vertex-on conformation at low ? , but a face-on conformation at high ? . / Master of Science

Developing methods to detect, adsorb, and decompose chemical warfare agents (CWAs) is of critical importance to protecting military and civilian populations alike. The sorption of dimethyl methylphosphonate (DMMP), a CWA simulant, into trisilanolphenyl-POSS (TPP) films has previously been characterized with reflection absorption infrared spectroscopy, x-ray photoelectron spectroscopy, and uptake coefficient determinations [1]. In our study, the quartz crystal microbalance (QCM) is used to study the sorption phenomena of DMMP into highly ordered Langmuir-Blodgett (LB) films of TPP. In a saturated environment, DMMP sorbs into the TPP films, binding to TPP in a 1:1 molar ratio. Although previous work indicated these DMMP-saturated films were stable for several weeks, DMMP is found to slowly desorb from the TPP films at room temperature and pressure. Upon application of vacuum to the DMMP-saturated films, DMMP follows first-order desorption kinetics and readily desorbs from the film, returning the TPP film to its original state. [1] Ferguson-McPherson, M.; Low, E.; Esker, A.; Morris, J. J. Phys. Chem. B. 2005, 109, 18914. / Master of Science

Liées de façon covalente à des chaînes polymères, les nanoparticules POSS (polysilses-quioxanes polyédriques) permettent l’obtention de matériaux nanocomposites hybrides orga-nique/inorganique. Ces nanoparticules présentent deux intérêts majeurs: des dimensions bien définies (cœur inorganique: 0.5 nm), ainsi que leur caractère hybride ( groupements organiques entourant les cages inorganiques). Les nanocomposites polymère/POSS peuvent présenter un renfort important des propriétés mécaniques et de la stabilité thermique de la matrice polymère. Cependant, l’origine moléculaire de ce renfort reste mal comprise. Aussi, afin de mieux comprendre le renfort des propriétés mécaniques de la matrice, nous avons étudié l’effet des particules POSS sur l’organisation à l’état solide et la dynamique des chaînes po-lymères au sein d’une matrice semi-cristalline. Pour cela, nous avons considéré une série de copolymères polyéthylène-POSS, caractérisés par une large gamme de concentration en POSS. Le polyéthylène et le POSS ayant intrinsèquement tendance à cristalliser, les copolymères présentent des organisations à l’état solide complexes que nous avons caractérisés par l’utilisation combinée de la calorimétrie différentielle à balayage (DSC), de la diffraction des rayons X aux grands angles (DRX) et de la résonance magnétique nucléaire en phase solide (RMN). Dans un second volet de cette étude, nous nous sommes intéressés à la dynamique des chaînes de polyéthylène en phase amorphe et à l’évolution de celle-ci avec le taux de charge des nanocomposites. Enfin, nous avons également étudié, de façon sélective, la dynamique des segments de chaînes de polyéthylène situés au voisinage de la charge / Grafting polyhedral oligomeric silsesquioxanes (POSS) to polymer chains offers a novel avenue to prepare hybrid organic/inorganic nanocomposites. The great advantage of such an approach holds in the very well-defined dimensions of the filler particles(inorganic core: 0.5 nm), in contrast with polymer/clay systems. Polymer/POSS nanocomposites display attractive properties such as significant mechanical reinforcement and increased thermal stability. However, the molecular origins of these enhancements are still an open question. The aim of this work is to describe both bulk organization and molecular motions of the polymer chains within these materials: these molecular properties should lead to a deeper knowledge of the enhancement of the polymer-POSS mechanical properties. The systems investigated are polyethylene (PE)-POSS copolymers with various POSS contents. The (semi-)crystalline behaviour of both PE and POSS particles induces complex bulk organization of these hybrid materials. The combined use of NMR, DSC and X-ray scattering experiments enabled to monitor the variation of the solid-state organization with the filler loading. In the second part of this work, the PE chain dynamics was investigated in the amorphous phase and its variation with the filler content was considered. Lastly, selective NMR experiments were used to probe the PE chain segment mobility close to the POSS nanoparticles

Neste trabalho foram estudados compósitos que apresentam como matriz polimérica uma blenda composta por polietileno de alta densidade (HDPE) e copolímero etileno acetato de vinila (EVA) e como nanocarga, silsesquioxano poliédrico oligomérico (POSS). Os compósitos foram processados em câmara de mistura fechada e caracterizados quanto às propriedades térmicas e morfológicas. Para a preparação dos compósitos foram variadas as concentrações dos componentes da blenda (0, 25, 50, 75 e 100%) e da nanocarga (0, 0,5, 1, 1,5, 2, 5 e 10%). Os resultados de processamento mostraram que o aumento da concentração de POSS na matriz polimérica provocou a agregação do mesmo na matriz polimérica. As análises de calorimetria diferencial de varredura e termogravimetria indicaram que o POSS não afetou as temperaturas de fusão, cristalização e degradação da matriz polimérica. Os resultados de raios X indicaram que a presença do EVA no compósito promoveu o aparecimento de domínios cristalinos em concentrações menores de POSS. A microscopia eletrônica de varredura indicou que as amostras com 1% de POSS apresentam distribuição homogênea na matriz polimérica. Por outro lado, ocorreu a formação de agregados nas amostras com 5% de POSS. Os valores de Tg obtidos por análise térmica dinâmico-mecânica indicaram que o POSS causou um efeito plastificante na fase HDPE e uma redução da mobilidade na fase EVA. Ocorreu um aumento nos valores de módulo de armazenamento com a incorporação de POSS na matriz polimérica. / Submitted by Marcelo Teixeira (mvteixeira@ucs.br) on 2014-05-22T19:03:21Z No. of bitstreams: 1 Dissertacao Patricia Scapini.pdf: 2020883 bytes, checksum: 2c7249d3915135dd5f3cba151cf459db (MD5) / Made available in DSpace on 2014-05-22T19:03:21Z (GMT). No. of bitstreams: 1 Dissertacao Patricia Scapini.pdf: 2020883 bytes, checksum: 2c7249d3915135dd5f3cba151cf459db (MD5) / In this study composites with a polymeric matrix comprising a blend of high density polyethylene (HDPE) and the copolymer ethylene vinyl acetate (EVA), and with polyhedral oligomeric silsesquioxane (POSS) as the nanoclay, were processed and characterized. The composites were processed in a closed mixing chamber and characterized in terms of their thermal and morphological properties. For the preparation of the composites the concentrations of the blend components (0, 25, 50, 75 and 100%) and of the nanoclay (0, 0.5, 1, 1.5, 2, 5 and 10%) were varied. The results of the processing showed that an increase in the POSS concentration in the polymeric matrix caused the aggregation of the system. The differential scanning calorimetry and thermogravimetry analyses indicated that the POSS did not affect the melt, crystallization and degradation temperatures of the polymeric matrix. The X-ray results indicated that the presence of EVA in the composite led to the appearance of crystalline domains at lower POSS concentrations. Scanning electron microscopy indicated that the samples with 1% of POSS have a homogeneous distribution in the polymeric matrix. However, the formation of aggregates occurred in samples with 5% of POSS. The Tg values obtained from the thermo dynamic mechanical analysis indicated that the POSS had a plasticizing effect on the HDPE phase and caused a reduction in the mobility of the EVA phase. There was an increase in the storage modulus values with the incorporation of POSS into the polymeric matrix.

Neste trabalho foram estudados compósitos que apresentam como matriz polimérica uma blenda composta por polietileno de alta densidade (HDPE) e copolímero etileno acetato de vinila (EVA) e como nanocarga, silsesquioxano poliédrico oligomérico (POSS). Os compósitos foram processados em câmara de mistura fechada e caracterizados quanto às propriedades térmicas e morfológicas. Para a preparação dos compósitos foram variadas as concentrações dos componentes da blenda (0, 25, 50, 75 e 100%) e da nanocarga (0, 0,5, 1, 1,5, 2, 5 e 10%). Os resultados de processamento mostraram que o aumento da concentração de POSS na matriz polimérica provocou a agregação do mesmo na matriz polimérica. As análises de calorimetria diferencial de varredura e termogravimetria indicaram que o POSS não afetou as temperaturas de fusão, cristalização e degradação da matriz polimérica. Os resultados de raios X indicaram que a presença do EVA no compósito promoveu o aparecimento de domínios cristalinos em concentrações menores de POSS. A microscopia eletrônica de varredura indicou que as amostras com 1% de POSS apresentam distribuição homogênea na matriz polimérica. Por outro lado, ocorreu a formação de agregados nas amostras com 5% de POSS. Os valores de Tg obtidos por análise térmica dinâmico-mecânica indicaram que o POSS causou um efeito plastificante na fase HDPE e uma redução da mobilidade na fase EVA. Ocorreu um aumento nos valores de módulo de armazenamento com a incorporação de POSS na matriz polimérica. / In this study composites with a polymeric matrix comprising a blend of high density polyethylene (HDPE) and the copolymer ethylene vinyl acetate (EVA), and with polyhedral oligomeric silsesquioxane (POSS) as the nanoclay, were processed and characterized. The composites were processed in a closed mixing chamber and characterized in terms of their thermal and morphological properties. For the preparation of the composites the concentrations of the blend components (0, 25, 50, 75 and 100%) and of the nanoclay (0, 0.5, 1, 1.5, 2, 5 and 10%) were varied. The results of the processing showed that an increase in the POSS concentration in the polymeric matrix caused the aggregation of the system. The differential scanning calorimetry and thermogravimetry analyses indicated that the POSS did not affect the melt, crystallization and degradation temperatures of the polymeric matrix. The X-ray results indicated that the presence of EVA in the composite led to the appearance of crystalline domains at lower POSS concentrations. Scanning electron microscopy indicated that the samples with 1% of POSS have a homogeneous distribution in the polymeric matrix. However, the formation of aggregates occurred in samples with 5% of POSS. The Tg values obtained from the thermo dynamic mechanical analysis indicated that the POSS had a plasticizing effect on the HDPE phase and caused a reduction in the mobility of the EVA phase. There was an increase in the storage modulus values with the incorporation of POSS into the polymeric matrix.

Les copolymères à blocs sont des matériaux très intéressants en raison de leur capacité à s’auto-organiser pour former des domaines de quelques dizaines de nanomètres. Cette organisation peut être mise à profit pour obtenir des matériaux hybrides organiques/inorganiques dans lesquels la phase inorganique peut être structurée dans un des domaines plutôt que répartie de façon aléatoire. Ceci peut conférer des propriétés particulières aux copolymères hybrides. Notre travail de thèse s’inscrit dans cette problématique. Des copolymères à blocs ont été modifiés soit par greffage en solution de molécules organiques/inorganiques du type POSS réactif (polyhedral oligomeric silsesquioxane), soit par mélange en solution ou à l’état fondu de POSS non réactif. Les copolymères triblocs considérés sont du type SBS (styrène-butadiène-styrène) et SEBS-g-MA (styrène-éthylène-butène-styrène greffé anhydride maléique). L’ensemble de ces copolymères a été caractérisé expérimentalement afin de déterminer leur morphologie et leur comportement thermo-mécanique. En parallèle une approche théorique a été proposée, basée sur la modélisation moléculaire de ces copolymères à l’échelle mésoscale. La méthode sélectionnée ‘Dissipative Particle Dynamics’ a permis de modéliser la morphologie de nos copolymères avec succès ainsi que celle de nos matériaux hybrides modifiés par les POSS. Ces derniers peuvent être dispersés à l’échelle moléculaire ou au contraire former des agrégats, selon le procédé de mise en œuvre et la structure chimique des POSS. / Experimental approaches and a modeling method have been carried out in parallele. The simulation method was used firstly to confirm the experimental results, and then will be applied to more complex nanocomposites. A series of hybrid systems based on triblock copolymer of polystyrene-butadiene-polystyrene (SBS) grafted with polyhedral oligomeric silsesquioxane(POSS) molecules with a dimethylsiloxy group (DMIPOSS) were synthesized by a hydrosilation method. The characteristics on incorporation of an unreactive POSS with constituent cyclohexyl (CyPOSS) in SBS matrix have been compared with above systems. The nanocomposites obtained were analyzed by atomic force microscopy, Transmission electron microscopy, X-ray scattering and dynamic mechanical.The same strategy has been carried out on polystyrene-b-poly (ethylene-co-butylene)-b-polystyrene-g-maleic anhydride (SEBS-g-MA) with other type of POSS. Dynamic particles dissipative (DPD) simulation methods in Materials Studio (Accelrys) were employed to study morphology of SB, SBS, SEBS and hybrid system. In this mesoscopic method, the polymer is simplified as a series of connecting beads which contains one or more monomer units. And all monomer units interact with each other following Newtonian Equations of Motion.