La technique de l’impression moléculaire permettant d'obtenir des polymères hautement sélectifs est utiliséedans de nombreuses applications. Dans le cadre de cette thèse, cette technique est employée pour préparer despolymères spécifiques du benzo(a)pyrène (BaP) en vue d’une application capteur. L’introduction d’une sonderédox au sein même du réseau de polymère offre la possibilité d’une détection directe de la cible, par unetechnique électrochimique. Dans le domaine des MIPs, ce travail est le premier à décrire l’utilisation d’unmonomère participant à la formation du réseau tridimensionnel tout en apportant une propriété rédox. Lespolymères synthétisés par polymérisation par précipitation ont été caractérisés en termes de composition, destabilité thermique et de propriétés texturales. Les propriétés de rétention ont été évaluées en mode batch parHPLC-UV en présence de BaP et d'interférents de type hydrocarbures aromatiques polycycliques. Ces MIPsprésentent de bonnes propriétés d’adsorption vis-à-vis du BaP avec des facteurs d’empreinte supérieurs à 1montrant l’efficacité de l’impression. Ces propriétés sont conservées en présence d’une matière organique (seld’acide humique), mais également après plusieurs cycles d’utilisation. Les analyses électrochimiques ontdémontré que les propriétés électrochimiques de ces MIPs diffèrent selon la présence ou pas de la cible avecune limite de détection de 0,09 μM en BaP, ouvrant la porte à la réalisation de capteurs. / Molecularly Imprinted Polymers show highly selective affinity towards the target molecule and are used inmany applications. In this context, the technology is used for preparing selective polymers for benzo(a)pyrene(BaP) with the aim of sensor fabrication. The addition of a redox tracer inside the polymer allows thepossibility of direct target detection by an electrochemical technique. In the MIP field, this work is the firstreporting the use of a functional monomer that not only participates in the creation of the polymer network butalso provides a redox property. The polymers synthesized using precipitation polymerization technique werecharacterized in terms of composition, thermal stability and textural properties. The adsorption properties wereevaluated in batch mode by HPLC-UV in the presence of BaP and interfering polycyclic aromatichydrocarbons. These MIPs show good adsorption behavior towards BaP with imprinting factors superior to 1showing the efficiency of the molecular imprinting. These properties were also preserved even in presence ofan organic matter (humic acid salt), and also after several uses. Finally, electrochemical analysis showed thatthese MIPs had a different electrochemical behavior depending on the presence or the absence of the targetwith a detection limit of 0.09 μM for BaP. The use of such electrochemical MIPs can thus be interestinglyconsidered in sensor devices.

Liquid chromatography is an analytical technique that is constantly facing new challenges in the separation of small molecules and large biomacromolecules. Recently the development of ultra high pressure liquid chromatography has increased the demand on sturdy particles as stationary phase. At the same time the particle size has decreased to sub-2 µm and packed into shorter analytical columns. This thesis deals with the development of new ways of preparing particulate polymer materials using divinylbenzene (DVB) as crosslinker. It includes a novel procedure for synthesizing monodisperse polymer particles by photoinitiated precipitation polymerization. A 150 W short arc xenon lamp was used to initiate the polymerizations. The synthesized particles are monodisperse and have an average particle size ranging from 1.5 to 4 μm depending on reaction conditions and have subsequently been used as grafting templates. The surface of DVB particles contains residual vinyl groups that serve as anchoring points for further functionalization via a variety of grafting schemes. Copolymerization with incorporation of 2,3-epoxypropyl methacrylate yielded pendant oxirane groups on the particle surface. Atom transfer radical polymerization (ATRP) was used to graft methacrylates from the surface resulting in a core-shell type material. A “grafting to” scheme was used to attach pre-made sulfopropyl methacrylate telomers onto particles containing oxirane rings. / Populärvetenskaplig sammanfattning på svenska: Vätskekromatografi är en analytisk kemisk teknik som ständigt står inför nya utmaningar när det gäller att separera allt från små organiska föreningar till stora makro¬molekyler. Denna avhandling beskriver tillverkning av polymera partiklar med exceptionellt jämn storleksfördelning och ytmodifiering av dessa, för användning som stationärfas i kromatografi¬kolonner. Polymeriserings¬tekniken som används är utfällnings¬polymerisering där lösningen UV-bestrålas av en 150 W xenonlampa. Monomeren (byggstenen) löses tillsammans med en intiator i ett lösningsmedel och efterhand som polymeriseringen fortskrider faller polymerpartiklarna ut. Polymerpartiklarna är gjorda av monomeren divinylbensen som fungerar som en tvärbindare, dvs att den länkar ihop flera kedjor till ett hårt litet nystan. Partiklarna växte till en storlek på 1,5 till 4 µm under två till fyra dygn. Efter tillverkningen är partiklarnas yta täckta av vinylgrupper som kan användas för att fästa funktionella polymerkedjor. Genom att tillföra monomeren 2,3-epoxipropyl¬metakrylat i polymeriseringen kunde man desutom få en partikelyta som innehöll epoxigrupper. Epoxigrupperna användes för att fästa positivt laddade polymerkedjor av bestämd längd. Materialet packades i en kromatografikolonn och användes för att separera en testlösning bestående av fyra proteiner. Partiklarna användes även som bas för ymppolymerisering där den vinyltäckta ytan fått reagera med vätebromid. Detta gör att partiklarna blir stora makroinitiatorer som kan användas för att på ett kontrollerat sätt låta polymerkedjor växa från ytan. I en undersökning ympades 2,3-epoxypropylmetakrylat från ytan på partiklarna och resultatet blev ett tjockt ytskikt. Epoxigrupperna kunde sedan hydrolyseras till dioler vilket gjorde partiklarna mer hydrofila.

Neste trabalho foi feito um estudo sobre a preparação e caracterização de microesferas poliméricas à base de poli(ácido metacrílico-co-divinilbenzeno) por polimerização por precipitação. As partículas foram sintetizadas e analisadas em diferentes condições de reação. Partículas esféricas políméricas foram sintetizadas na faixa de 1,66 - 8,41 m, assim como partículas no estado de microgel. As partículas foram caracterizadas pelas técnicas de espalhamento de luz dinâmica (DLS), análise termogravimétrica (TGA), espectroscopia na região do infravermelho (FTIR), adsorção de nitrogênio pelos métodos BET (Brunauer, Emmett e Teller) e BJH (Barret, Joyner e Halenda), microscopia ótica, microscopia eletrônica de varredura, e testes de razão de inchamento. A análise das partículas foi feita para verificar a influência da mudança na composição de comonômeros, grau de reticulação, relação de monômeros totais/diluentes em massa/volume (g/100 mL), e quanto à relação volumétrica de diluentes. Verificou-se que houve um aumento no tamanho das partículas e da resistência térmica com a diminuição da fração molar de MAA (ácido metacrílico). Na preparação de partículas com fração molar de 50% de MAA, e relação volumétrica acetonitrila/tolueno de 75/25, quanto maior a relação de monômeros totais/diluentes (g/100 mL), maior o tamanho e o rendimento das partículas. Com a mudança da relação volumétrica de diluentes, houve mudança nas características de porosidade, tamanho das partículas, e grau de inchamento das partículas, sendo que na relação volumétrica acetonitrila/tolueno de 50/50, houve formação de microgel / The preparation and characterization of polymeric microspheres based on poly(methacrylic acid-co-divinylbenzene) by precipitation polymerization was reported. The particles were synthesized and analyzed at different reaction conditions. Spherical polymer particles were synthesized in the range from 1,66 to 8,41 m, in addition to microgel particles. The particles were characterized by dynamic light scattering (DLS), thermogravimetric analysis (TGA), infrared spectroscopy (FTIR), nitrogen adsorption methods by BET (Brunauer, Emmett and Teller) and BJH (Barrett, Joyner and Halenda), optical microscopy, scanning electron microscopy, and swelling ratio tests. The particles analysis was made to determine the influence of the change in comonomer composition, degree of crosslinking, ratio of total monomers/diluents by weight / volume (g/100 mL), and the volume ratio of diluents. It was found that there was an increase in particle size and thermal resistance with decreasing molar fraction of MAA (methacrylic acid). In preparing particles with the mole fraction of 50% MAA, and volume ratio acetonitrile/toluene 75/25, the larger the ratio of total monomers/diluents (g/100 mL), the larger the particle size and yield. By changing the volume ratio of diluents, there was a change in the characteristics of porosity, particle size and degree of swelling of the particles, and in the volume ratio acetonitrile / toluene of 50/50, there was microgel formation

Neste trabalho foi feito um estudo sobre a preparação e caracterização de microesferas poliméricas à base de poli(ácido metacrílico-co-divinilbenzeno) por polimerização por precipitação. As partículas foram sintetizadas e analisadas em diferentes condições de reação. Partículas esféricas políméricas foram sintetizadas na faixa de 1,66 - 8,41 m, assim como partículas no estado de microgel. As partículas foram caracterizadas pelas técnicas de espalhamento de luz dinâmica (DLS), análise termogravimétrica (TGA), espectroscopia na região do infravermelho (FTIR), adsorção de nitrogênio pelos métodos BET (Brunauer, Emmett e Teller) e BJH (Barret, Joyner e Halenda), microscopia ótica, microscopia eletrônica de varredura, e testes de razão de inchamento. A análise das partículas foi feita para verificar a influência da mudança na composição de comonômeros, grau de reticulação, relação de monômeros totais/diluentes em massa/volume (g/100 mL), e quanto à relação volumétrica de diluentes. Verificou-se que houve um aumento no tamanho das partículas e da resistência térmica com a diminuição da fração molar de MAA (ácido metacrílico). Na preparação de partículas com fração molar de 50% de MAA, e relação volumétrica acetonitrila/tolueno de 75/25, quanto maior a relação de monômeros totais/diluentes (g/100 mL), maior o tamanho e o rendimento das partículas. Com a mudança da relação volumétrica de diluentes, houve mudança nas características de porosidade, tamanho das partículas, e grau de inchamento das partículas, sendo que na relação volumétrica acetonitrila/tolueno de 50/50, houve formação de microgel / The preparation and characterization of polymeric microspheres based on poly(methacrylic acid-co-divinylbenzene) by precipitation polymerization was reported. The particles were synthesized and analyzed at different reaction conditions. Spherical polymer particles were synthesized in the range from 1,66 to 8,41 m, in addition to microgel particles. The particles were characterized by dynamic light scattering (DLS), thermogravimetric analysis (TGA), infrared spectroscopy (FTIR), nitrogen adsorption methods by BET (Brunauer, Emmett and Teller) and BJH (Barrett, Joyner and Halenda), optical microscopy, scanning electron microscopy, and swelling ratio tests. The particles analysis was made to determine the influence of the change in comonomer composition, degree of crosslinking, ratio of total monomers/diluents by weight / volume (g/100 mL), and the volume ratio of diluents. It was found that there was an increase in particle size and thermal resistance with decreasing molar fraction of MAA (methacrylic acid). In preparing particles with the mole fraction of 50% MAA, and volume ratio acetonitrile/toluene 75/25, the larger the ratio of total monomers/diluents (g/100 mL), the larger the particle size and yield. By changing the volume ratio of diluents, there was a change in the characteristics of porosity, particle size and degree of swelling of the particles, and in the volume ratio acetonitrile / toluene of 50/50, there was microgel formation

Submitted by Biblioteca da Faculdade de Farmácia (bff@ndc.uff.br) on 2017-03-23T19:00:13Z No. of bitstreams: 1 Peçanha, Bruna Rachel de Britto [Dissertação, 2012].pdf: 3907379 bytes, checksum: f2acabc3c1c39363b86f0d651d6b5936 (MD5) / Made available in DSpace on 2017-03-23T19:00:13Z (GMT). No. of bitstreams: 1 Peçanha, Bruna Rachel de Britto [Dissertação, 2012].pdf: 3907379 bytes, checksum: f2acabc3c1c39363b86f0d651d6b5936 (MD5) / Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Polímeros de impressão molecular (MIPs) foram sintetizados e aplicados como adsorventes na técnica de extração em fase sólida (EFS). O método de polimerização por precipitação foi utilizado para a síntese dos polímeros, devido à simplicidade de preparo, altos rendimentos e obtenção de partículas mais uniformes, devido a não trituração do polímero. O MIP foi sintetizado com ácido metacrílico (MAA) como monômero funcional, trimetacrilato de trimetilolpropano (TRIM) e dimetacrilato de etilenoglicol (EDMA) como agentes de reticulação e o cloridrato de amilorida (AMI) foi escolhido como molécula-molde. Diferentes proporções de MAA, TRIM, EDMA, volume e tipo de solvente foram utilizadas para ajuste das condições ideais de síntese. Os MIP foram avaliados quanto à capacidade de adsorção comparando-se a polímeros sintetizados na ausência da molécula-molde (NIP, polímeros não impressos). O solvente de elevada polaridade empregado na síntese (THF:MeOH:H2O) permitiu o emprego da técnica para moléculas polares como AMI. O controle no volume de solvente permitiu a obtenção de partículas maiores, de modo que a EFS foi realizada em condições usuais, o que confere um potencial para aplicação dessa técnica de polimerização na preparação de adsorventes para EFS. O polímero que apresentou maior capacidade adsortiva no ensaio realizado em tampão citrato-acetato pH 6,5 foi o MIP/NIP 12 (AMI:MAA:TRIM 1:8:10), com uma taxa média de adsorção de 83 e 88% para NIP e MIP, respectivamente. A adsorção foi elevada devido a interação iônica entre MAA e AMI promovida pelo controle de pH, porém foi não específica. O polímero MIP/NIP 12 foi aplicado como adsorvente na EFS, onde a recuperação de AMI foi avaliada nos resíduos de carregamento e eluição com solventes. O carregamento com tampão citrato-acetato pH 6,5 foi o ideal, favorecendo a interação iônica do polímero com o analito. A eluição total de AMI do cartucho somente ocorre após lavagem com o solvente na presença de ácido, que protona os grupos carboxila do polímero, rompendo assim a interação iônica com o analito / Molecularly imprinted polymers (MIPs) were synthesized and applied as adsorbents in solid-phase extraction technique (SPE). The polymers have been synthesized by precipitation polymerization method because of its simplicity, high yields and good control of final size and shape of particles. MIP was synthesized using methacrylic acid (MAA) as functional monomer, trimethylolpropane trimethacrylate (TRIM) and ethyleneglycol dimethacrylate (EDMA) as cross-linker and amiloride hydrochloride (AMI) was chosen as template. Different ratios of MAA, TRIM and EDMA, volume and type of solvent were used to adjust the optimal synthesis conditions. The MIP were tested for adsorption capacity compared to the polymers synthesized in the absence of template molecule (NIP, non-imprinted polymers). The polar solvent mixture used (THF:MeOH:H2O) allowed the synthesis of MIP of polar molecules as AMI. The solvent volume control afforded the larger particles so the SPE was performed in the usual conditions, giving a potential application for this polymerization technique in the preparation of adsorbents for SPE. The polymers with higher adsorption capacity at the test performed in citrateacetate buffer pH 6,5 was MIP/NIP 12 (AMI:MAA:TRIM 1:8:10) with adsorption rate of 83 and 88% for NIP and MIP, respectively. The recognition of MIP was due to ionic interaction between MAA and AMI promoted by pH control, but was not specific. The polymer MIP/NIP 12 was used as a solid-phase extraction sorbent and the recoveries of AMI was evaluated using different loading and elution conditions. The loading with buffer citrate-acetate pH 6,5 was optimal, due to ionic interaction of the polymer with the analyte. Total elution of AMI bound to the polymers only occurs after washing with a acid-containing solvent, because of protonation of the carboxyl groups of the polymer and disrupting the ionic interaction with the analyte

Lors de cette étude, il a été étudié l'influence de l'ajout de microparticules de polymère réticulé (CPM) dans des formulations d'époxy-amine, sur la cinétique, la morphologie et les propriétés thermo-mécaniques des réseaux finaux obtenus. Tout d'abord, un protocole simple, robuste et bien contrôlé a été développé afin d’ obtenir une large gamme de taille de CPM, de Tg et de fonctionnalité amine. Ce protocole de polymérisation par précipitation, basé sur les phénomènes de séparation de phases, a également été appliqué à différentes compositions chimiques et différents monomères époxy hydrosolubles, ceci montrant les grandes possibilités de cette méthode. Une bonne interface entre les CPMs et la matrice a été recherchée en synthétisant les CPMs en excès de groupes amines. La quantification de ces groupes amines réactifs sur les CPMS était d'un grand intérêt et a donc été étudiée en profondeur. Le titrage des amines de surface a été réalisé en mettant au point un nouveau protocole qui a permis la quantification des amines primaires et secondaires sur les CPMs. Il a ensuite été mis en évidence que, bien que ces microparticules réticulées ne soient pas poreuses, des fonctions amines sont disponibles au cœur des particules et peuvent réagir avec d'autres molécules qui sont capables de diffuser dans la CPM. Il a été montré que lorsque les CPM ont été dispersées dans des mélanges d'époxy- amine, la diffusion des monomères dans le cœur de la CPM s'est produite mais différemment selon le procédé de dispersion. En effet, en utilisant le tétrahydrofurane comme solvant pour aider à la dispersion, la diffusion de la DGEBA est amplifiée et modifie les propriétés thermo-mécaniques du réseau final en modifiant le rapport stœchiométrique de la matrice. Le même phénomène a été observé mais moins amplifié lorsque les microparticules sont uniquement dispersées mécaniquement. En dispersant les CPMs dans l'amine qui est l'agent réticulant, on observe l'absorption complète de l'amine au coeur des CPMs, conduisant ainsi à la désorption de celle-ci dans une deuxième étape, permettant de créer le réseau. Ainsi, un comportement très complexe des CPM a été mis en évidence en présence des monomères et/ou solvant : le gonflement et les phénomènes de diffusion qui dépendent d'un certain nombre de paramètres tels que la température, la densité de réticulation des CPM, les paramètres de solubilité, etc. L'intensité du phénomène de diffusion conduit à une variété de comportements lorsque les CPMs sont ajoutées dans une formulation d'époxy-amine tels que: (a) une légère diminution du temps de gélification et l'augmentation de la conversion, (b) la modification de la température de transition vitreuse de la matrice. / Throughout this work, the influence of the addition of cross-linked polymer microparticles (CPMs) in epoxy-amine formulations on the kinetics, morphology and thermo-mechanical properties of the final networks have been investigated. First, an easy, robust and well-controlled protocol was developed to obtain a large range of CPM size, Tg and amine functionality. This protocol based on reaction induced phase separation via precipitation polymerization was also applied to different chemistries and water soluble epoxy pre-polymers showing the large possibilities of this method. The capacity of obtaining a good compatibility between the CPMs and the matrix was ensure by synthesizing the CPMs in excess of amino groups. The study of the remaining reactive amino groups on the CPMS was of great interest and therefore deeply investigated. The titration of the surface amine was performed by developing a new protocol that enabled the quantification of primary and secondary amines on CPMs. It was then highlighted that even though these cross-linked microparticles were not porous, amino groups are available into the core and can react with other molecules that are able to diffuse into the CPM core. It was shown that when CPMs were dispersed into epoxy-amine blends, the diffusion of monomers into the CPM core occurred but differently depending on the dispersion process. Indeed, using tetrahydrofuran as solvent to help for the dispersion increased the diffusion of DGEBA into the CPM core and changed the thermo-mechanical properties of the final network by modifying the stoichiometric ratio of the matrix. Same phenomenon was observed but less amplified when CPMs were mechanically dispersed in DGEBA. Regarding the dispersion of CPMs in the amine cross-linker, IPD, its complete absorption could be observed into the CPMs, leading then to the desorption of IPD to create the network. Thus, a very complex behavior of CPMs was highlighted in presence of monomers or/and solvent: swelling and diffusion phenomena that are dependent on a number of parameters such as temperature, CPM cross-link density, solubility parameters, etc. The intensity of those phenomena leads to a variety of behaviors when CPMs are added into an epoxy-amine formulation: (a) slight decrease of gel times and increase of conversion, (b) modification of glass transition temperature of the matrix.