This Master's thesis deals with the evaluation of a current state of two-generation villa and its following proposal of the optimization. Evaluation includes calculation of heat loss of a current state. Optimization is based on the reduction of heat loss in the building, pressure balance of the system, change of heat source and installation of balanced ventilation. Chapter describing regulation of technology follows and in conclusion indicative price for the whole suggested technology is calculated.

The diploma thesis is divided into four main parts. The first part deals with the issue of waste management and its energy utilization in waste incineration. Processed harmful substances produced by incineration as well as emission limits. It deals with the types of catalytic carriers, their description, production and more detailed processing of ceramic foam VUKOPOR. The second part is devoted to technologies utilizing catalytic processes and a more detailed specification of the process. In the third part there is processed the calculation methods for pressure losses for individual types of carriers. Fourth, the most extensive part describes the INTEQII experimental device, its technology and construction, as well as the principle of the practical part, measuring of the pressure losses of carriers. It includes the evaluation of pressure losses in separate categories of carriers, such as the bed, HoneyComb and VUKOPOR ceramic foam. Subsequently, a comparison of the pressure losses of all carriers is made relative to the reference size of 1 m. The impact of bonding of VUKOPOR foam samples on the size of pressure losses is discussed. At the end of this section, the suitability of calculation methods for individual carriers is evaluated, depending on the experimental pressure loss data.

The thesis aims to design a device for utilization of waste heat for heating and hot water in NETME Centre in area of FSI VUT in Brno. First of all there is summary of available sources of waste heat and evaluation of serviceability. Next there is design of a device for utilization of waste heat. Design incluades calculation of heat exchangers and selection of particular heat exchangers. It also incluades design of duct system which anables transportation of heated water from heat exchangers to machine room. In machine room is situated storage tank for accumulation of gained waste heat. This storage tank is conected to heating system and to consumption of hot water which anables utilization of waste heat. Finally there is economic evaluation based on amount of gained waste heat, consumption of heat and costs.

The theoretical part of the thesis deals with the hydraulics of heating systems. The aim of the project is a design of the heating and hot water preparation system for an apartment building. The building has 6 above-ground floors and 2 underground floors. Two different options of heating systems were designed, comparison and results are presented in the thesis. In the first case the heat source during the winter season and for water heating, where chosen two gas condensing boilers, situated in separated room on the second underground floor. In the second case, each apartment has its own gas condensing boiler. The experimental part of the project deals with measurements of pressure losses in water armatures used in heating systems. The aim of this part is the determination of coefficients of added resistance for uncontrolled elements, which are normally presented as tabular value. In thesis are presented results for a ball valve, backflow preventer, filter, for slide valve and thermostatic valve. Measurements for thermostatic valve where done with different settings and results are compared with parameters listed in the datasheet.

This diploma thesis deals with pressure losses in heating systems. The diploma thesis is divided into three sections. The first part is theoretical and deals with the occurrence of pressure losses. It discusses the properties of the fluid that affect pressure losses. It also deals with hydrodynamic phenomena, flow distribution, pressure loss distribution and its calculations. The aim of the second part, which is practical, was to create a heating project for a selected object. The object is a two-floor kindergarten building located in Velké Němčice. For this project, two heating variants were created. For the first variant, radiators and heating benches were designed and for the second variant, underfloor heating was installed in the building. The goal was to use a source which will gain heat mainly from renewable sources, so the air / water heat pump was chosen as the source of heat production. The project ends with a technical report. The third part of the thesis is dedicated to an experiment which purpose was to find out how the pressure losses of the connecting pieces are reacting to the change with the change of the heating water conditions (flow, temperature). Alongside, two pipes were created which differed in the type of connecting pieces so it allowed to compare how their pressure losses differ. Both pipes were connected by radial pressing, but the fittings differed in the quality of the brass, and therefore in the construction. Also, part of the experimental section of the diploma thesis is a description of the course of radial pressing of fittings from the Herz company.