Modern construction practices require proper knowledge to predict concrete pumping pressure, especially in high-volume and high-rise applications. Despite the progress made over the last decades, the spread of concrete pumping to high-rise construction has been hampered by the lack of standardized operating procedures and performance criteria. By and large, the guidelines available today focus predominantly on pumping Conventional Vibrated Concrete (CVC), while ambiguity still surrounds pumping Self-Consolidating Concrete (SCC) and other types of Highly-Workable Concrete (HWC). This PhD dissertation focuses on the fundamental principles relevant to the flow of high-strength SCC in pumping pipes, and it aims to develop methods to predict and reduce the required pumping pressure. The flow pattern of SCC in pipes is analytically investigated, providing a numerical approach to predict the pumping pressure based on the properties of both concrete and the lubrication layer, the pipe diameter, and the flow rate. The analytical results are further validated through full-scale pumping tests executed at the laboratory of the Université de Sherbrooke. Through this phase 26 optimal concrete mixtures were pumped in a 30-m pumping circuit to investigate the interactions between the concrete properties and pressure loss. The same tests are also employed to empirically correlate pressure loss with rheological and tribological properties of concrete at different flow rates. The resulting correlations furnish instrumental models capable of computing pressure loss for a wide range of concrete properties. In another application, the experimental results are analyzed to identify the influence of pumping on concrete properties with time. Full-scale pumping results are statistically analyzed in order to establish a quantitative description of the most influential parameters governing the concrete flow in pipes. As a result, concrete pipe flow is statically modeled, allowing the computation of pressure loss at different flow rates based on the the rheological and tribological properties of the concrete and the pipe diameter. Another statistical model is derived to calculate the pressure loss as a function of the V-funnel flow time, granting the advantage of predicting the pressure loss on job sites without the need for complex rheological and tribological measurements. In light of the research findings of the previous phases, a new simple test method called the pipe flow test (PFT) is developed in the context of this research, specifically for predicting pipe flow pressure loss. With preceding research phases as insights, the final stage of this project is directed toward mix design optimization faced with the challenge of reducing the pumping pressure and meeting the strength requirements of high-strength SCC. Ultimately, the research findings emanating from this investigation provide practical guidelines and conclusive models to predict and reduce pumping pressure for a wide scope of concrete mixtures and pipe diameters.

[pt] O presente trabalho analisa a transferência de calor e a perda de carga em escoamento turbulento através das regiões anulares lisas e aletadas. Os coeficientes de transferência de calor foram obtidos experimentalmente, utilizando-se a teoria de trocadores de calor. Também foram determinados os coeficientes de perda de carga associados a cada uma das geometrias analisadas. Os experimentos foram realizados em um trocador de calor bi-tubular concêntrico. Água (fluído quente) escoava através do tubo interno, enquanto ar (fluido frio) fluía através da região anular. Medindo-se as vazões e temperaturas na entrada e saída da seção de teste do trocador de calor, obtém-se a efetividade da mesma e, consequentemente, o coeficiente global de transferência de calor (médio). As condições de contorno adotadas foram de temperatura uniforme na superfície externa do tubo interno e de isolamento térmico na superfície externa do tubo interno e de isolamento térmico na superfície externa da região anular. Com o objetivo de obter-se condições de escoamento completamente desenvolvido, o trocador de calor possui um comprimento, a montante da seção de testes, de aproximadamente trinta diâmetros hidráulicos. Os coeficientes de transferência de calor e de perda de carga são apresentados de forma adimensional, como função do número de Reynolds do escoamento, os resultados obtidos para as regiões anulares lisas e aletadas são comparados entre si. O propósito de tal comparação foi o de estudar a influencia das aletas na perda de carga e na taxa de transferência de calor. No caso das regiões aletadas, verifica-se que a eficiência das aletas influencia a transferência de calor. Deste modo, realizou-se uma análise bi-dimensional de transferência de calor nas aletas para obter-se a eficiência das mesmas e, consequentemente, a eficiência das regiões aletadas. Também é mostrado que o desempenho térmico da região depende principalmente do número de Nusselt e da eficiência da mesma. Tais parâmetros são apresentados, em última análise, como funções do número de Reynolds e da geometria do problema. / [en] The present work is concerned with the turbulent heat transfer and pressure drop in smooth and finned annular ducts. Average heat transfer coeeficients have been obtained by means of the heat exchanger theory. In addition, friction factors have also been determined. The experiments were performed by utiling four double-pipe heat exchangers. The average heat transfer coefficients, for air flowing in the annular section, were fertmined by measuring the overall heat transfer coefficients of the heat exchangers. In order to aatain fully developed conditions, the heat exchangers had a starting length of 30 hydrualic diameters. The thermal boundary conditions consisted of uniform temperature on the inner surface, the outer surface being insulate. The heat transfer coefficients and friction factors are presented in dimensinless forms, as functions of the Reynolds number of the fow. The results for smooth and finned annular ducts were compared. The purpose of such comparison was to study the influence of the fins on the pressure drop and heat transfer rate. In the case of the finned annular ducts, it is shown that fin efficiency has some influence on the heat transfer rates. Then a two-dimensional heat transfer analysis was performed in order to obtain the fin efficiency and the annular region efficiency. It is also shown that the overall thermal performance of finned surfaces depends mainly of the Nusselt number and on the region efficiency. These parameters are presented as functiond of the Reynolds number of the flow and the geometry of the problem.

The diploma thesis titled, Computational model of shock absorber, is concerned with ways to simulate individual actuators of dampening with the goal of obtaining F-v characteristics dependent on the setup of the shock absorber. The work is divided into two halves, the first one being a review of literature and the second half being practical. The review part is focused on ways of shock absorber constructions and the physical principles involved with the present forces. The practical part of the work contains a computational model of a monotube shock absorber in the Matlab programming software.

The master thesis deals with the replacement of heat exchanger surfaces during simulations in the ANSYS Fluent. The aim of this work is to find a simplified model of the heat exchanger usable for flow simulations in large process and energy units, where it is not possible to model the entire heat exchanger in detail. The calculation procedures are applied to „tube bank” heat exchanger. The master thesis is divided into three parts. First part deals with pressure losses. The "porous zone" approach is used as a replacement for the heat exchanger surface. In the second part, the heat transfer by convection and conduction through the heat exchanger is replaced by the "Heat Exchanger" module. The third part examines the influence of material properties, heat source and fixed temperatures on incident radiation. All calculations resulting from the methods are performed using a script that prepares the output data in format suitable for insertion into ANSYS Fluent. A simplification, which faithfully replaces a fully modeled heat exchanger, has been found in all three parts of the thesis.

This master’s thesis deals with the simulation of flow through the normalized orifice plate. There is described flow measurement with flowmeters, which reduces the cross-section of the pipe and causes the pressure difference before and after the flowmeter. Following is a description methods of modeling of turbulent flow and a description of software for the simulation of flow from the company Ansys. The theoretical part is followed a practical part, which is focused on determining the permanent pressure loss caused by the orifice plate and the verification of straight pipeline lengths between orifice and obstacle.

This diploma thesis deals with a design of a boiler for stillage combustion. Stoichiometric calculations and enthalpies of combustion gases have been calculated from the specified parameters. In addition, heat calculation, design of the combustion chamber dimensions and dimensioning of heat surfaces were accomplished. The boiler has an evaporator with natural circulation and a fire grate.

The present thesis deals with a design of a heating system for reconstructed family house. The heat loss was calculated according to ČSN EN 12831 Heating systems in buildings – Method for calculation of the heating load. The projected system was regulated. Hot water generation and the safety devices, such as safety valve or expansion tank, were designed. The total costs were calculated afterwards.

This master thesis has two goals: First is to design a Permit Set of Drawings for a combined building of studios, classrooms and theather hall with neccesary auxilary facilities in Brno. Building is detached, five-storey with a basement. In the basement there are garages, theather hall with with facilities and HVAC technologies. The load-bearing structure is prefabricated reinforced concrete frame with ceramic masonry envelope and partitions. Roof is designed as a flat green roof. Building should fulfil the passivhaus requirements. The second goal of the thesis is to assess and compare common metal-based air-conditioning tubing with system based on stone-wool materials called CLIMAVER. The assessment and comparison is based on experimental measurements of the systems’ pressure losses.

Highly loaded single stage gas turbines are being developed to minimize the turbine size and weight. Such highly loaded turbines often result in transonic flows, which imply a reduction in the efficiency due to the shock losses. The efficiency of a turbine is defined as the ratio between the real work extracted by the turbine rotor from the fluid and the maximum available enthalpy for a given pressure ratio. The relationship between turbine performance and design parameters is not yet fully comprehended due to the complexity of the flow field and unsteady flow field interactions. Hence, experimental and numerical studies remain necessary to understand the flow behavior at different conditions to advance the state of the art of the prediction tools. The purpose of the current research is to develop a methodology to determine the efficiency with an accuracy better than 1 % in a cooled and uncooled high pressure (HP) turbine tested in a short duration facility with a running time of about 0.4s. Such low level of uncertainty requires the accurate evaluation of a large number of quantities simultaneously, namely the mass flow of the mainstream, the coolant, and leakage flows properties, the inlet total pressure and total temperature, the stage exit total pressure, the shaft power, the mechanical losses and the heat transfer. The experimental work is carried out in a compression tube facility that allows testing the turbine at the temperature ratios, Re and Mach numbers encountered in real engines. The stage mass flow is controlled by a variable sonic throat located downstream of the stage exit. Due to the absence of any brake, the turbine power is converted into rotor acceleration. The accurate measurement of this acceleration as well as those of the inertia and the rotational speed provides the shaft power. The inertia of the whole rotating assembly was accurately determined by accelerating and decelerating the shaft with a known energy. The mass-flow is derived from the measured turbine inlet total pressure and the vane sonic throat. The turbine sonic throat was evaluated based on a zero-dimensional model of the turbine. The efficiencies of two transonic turbines are measured at design and off-design conditions. The turbine design efficiency is obtained as 91.8 %. The repeatability of the measurements for 95% confidence level varies between 0.3 % and 1.1 % of the efficiency depending on the test case. The theoretical uncertainty level of 1.2 % is mainly affected by the uncertainty of exit total pressure measurements. Additionally, the effect of vane trailing edge shock formations and their interactions with the rotor blade are analyzed based on the experimental data, the numerical tools and the loss correlations. The changes of blade and vane performances are measured at mid-span for three different pressure ratios which influence the vane and rotor shock mechanisms. Moreover, the unsteady forces on the rotor blades and the rotor disk were calculated by integration of the unsteady static pressure field on the rotor surface.

This study aims to investigate hydraulics and the flow characteristics of drilling fluids inside annulus and to understand the mechanism of cuttings transport in horizontal and deviated wellbores. For this purpose, initially, extensive experimental studies have been conducted at Middle East Technical University, Petroleum &amp / Natural Gas Engineering Flow Loop using water and numerous drilling fluids for hole inclinations from horizontal to 60 degrees, flow velocities from 0.64 m/s to 3.05 m/s, rate of penetrations from 0.00127 to 0.0038 m/s, and pipe rotations from 0 to 120 rpm. Pressure loss within the test section and stationary and/or moving bed thickness are recorded. New friction factor charts and correlations as a function of Reynolds number and cuttings bed thickness with the presence of pipe rotation for water and drilling fluids in horizontal and deviated wellbores are developed by using experimental data. Meanwhile empirical correlations that can be used easily at the field are proposed for predicting stationary bed thickness and frictional pressure loss using dimensional analysis and the effect of the drilling parameters on hole cleaning is discussed. It has been observed that, the major variable influencing cuttings transport is fluid velocity. Moreover, pipe rotation drastically decreases the critical fluid velocity that is required to prevent the stationary cuttings bed development, especially if the pipe is making an orbital motion. A decrease in the pressure loss is observed due to the bed erosion while rotating the pipe. Cuttings transport in horizontal annulus is modeled using a CFD software for different fluid velocities, pipe rotation speeds and rate of penetrations. The CFD model is verified by using cuttings transport experiments. A mathematical model is also proposed to predict the flow characteristics of Newtonian fluids in concentric horizontal annulus with drillpipe rotation. The Navier-Stokes equations of turbulent flow are numerically solved using finite differences technique. A computer code is developed in Matlab 2007b for the proposed model. The performance of the proposed model is compared with the experimental data which were available in the literature and gathered at METU-PETE Flow Loop as well as Computational Fluids Dynamics (CFD) software. The results showed that the mechanistic model accurately predicts the frictional pressure loss and the velocity profile inside the annuli. The model&rsquo / s frictional pressure loss estimations are within an error range of &plusmn / 10%.