First- principles modeling is used to predict hydrogen permeability through Palladium (Pd)-rich binary alloy membranes as a function of temperature and H2 pressure. We introduce a simplified model that incorporates only a few factors and yields quantitative prediction. This model is used to predict hydrogen permeability in a wide range of binary alloy membranes and to find promising alloys that have high hydrogen permeability. We show how our efficient Density Functional Theory (DFT)-based model predicts the chemical stability and proton conductivity of doped barium zirconate (BaZrO3), barium stannate (BaSnO3), and barium hafnate (BaHfO3). Our data is also used to explore the physical origins of the trends in chemical stability and proton conductivity among different dopants. We also study potassium tantalate (KTaO3), which is a prototype perovskite, to examine the characteristics of undoped perovskites. Specifically, we study the impacts of isotope effects, tunneling effects, and native point defects on proton mobility in KTaO3. It is important to find and develop solid-state Li-ion electrolyte materials that are chemically stable and have high ionic conductivities for high performance Li-ion batteries. We show how we predict the chemical stability of Li7La3Zr2O12, Li7La3Sn2O12, and Li7La3Hf2O12 with respect to carbonate and hydroxide formation reactions.

京都大学 / 新制・課程博士 / 博士(理学) / 甲第24873号 / 理博第4983号 / 新制||理||1711(附属図書館) / 京都大学大学院理学研究科化学専攻 / (主査)教授 北川 宏, 教授 有賀 哲也, 教授 堀毛 悟史 / 学位規則第4条第1項該当 / Doctor of Science / Kyoto University / DGAM

Novel ceramic membrane cells of BaCe₀.₅Zr₀.₃Y₀.₁₆Zn₀.₀₄O[subscript(3-δ)] (BCZYZ), a proton-conducting oxide, have been developed for electrocatalytic ammonia synthesis. Unlike the industrial Haber-Bosch process, in this work an attempt to synthesise ammonia at atmospheric pressure has been made. The membrane cell fabricated by tape casting and solution impregnation comprises of a 200 μm-thick BCZYZ electrolyte and impregnated electrode composites. Electrocatalysts for anode and cathode were investigated. For the anode, the co-impregnation of Ni and CeO₂ provided excellent electrode performance including high catalytic activity, sintering stability and compatibility with the BCZYZ electrolyte. The best composition was the mixture of 25 wt% NiO and 10 wt% CeO₂. A symmetrical cell prepared with this electrode composition revealed low polarisation resistances of 1.0 and 0.45 Ωcm² in humidified 5% H₂/Ar at 400 and 500 °C, respectively. For the cathode, 25 wt% of impregnated Fe oxide provided a satisfactory performance in non-humidified N₂ atmosphere. Significant amounts of ammonia were produced from the single cell with Ni-CeO₂ anode and Fe oxide cathode at 400-500 °C under atmospheric pressure. Ammonia formation rate was enhanced by Pd catalyst addition and electrochemical performance was improved by Ru addition. The highest ammonia formation rate of 4 x 10⁻⁹ mols⁻¹cm⁻² was attained using the cell with a Pd-modified Fe cathode at 450 °C. The formation reaction of ammonia typically consumed around 1-2.5 % of total applied current while most of the applied current was employed in H⁺ reduction. The total current efficiency of around 90-100 % could be obtained from the membrane cells.

Ce travail s'inscrit dans le cadre du développement des piles à combustible à céramique conductrice protonique (PCFC) opérant dans le domaine de température 400 – 600 °C et concerne l'optimisation des composants de la cellule élémentaire. L'optimisation du matériau électrolytique consiste à rechercher le meilleur compromis entre stabilité chimique et conductivité élevée. Le matériau BaCe0.9Y0.1O2.95, synthétisé par la voie flash combustion, présente la conductivité protonique la plus élevée (10-2 S.cm-1 à 600 °C) mais réagit fortement avec le CO2. La substitution partielle du cérium par le zirconium (BCZY) et le niobium (BCYN30) a conduit à une amélioration significative de la stabilité chimique tout en conservant une conductivité de l'ordre de 5 × 10-3 S.cm-1 à 600 °C. En ce qui concerne les électrodes, l'enjeu est de développer des matériaux présentant une conductivité électronique élevée, une porosité suffisamment importante et une bonne tenue mécanique. L'approche a consisté en la mise au point de stratégies d'élaboration (synthèse en une étape, utilisation de porogène) permettant le contrôle de la microstructure des matériaux anodiques afin de minimiser les résistances spécifiques surfaciques (ASR). Comme dans le cas des SOFC, les matériaux cathodiques sont conducteurs mixtes ionique-électronique (MIEC). Le développement de cathodes composites MIEC-électrolyte a permis de réduire significativement les ASR. Les tests en pile de cellules élémentaires PCFC ont révélé que les performances dépendaient essentiellement de la nature et de l'épaisseur du matériau électrolytique et de la mise en œuvre de matériaux d'électrode de morphologie contrôlée et architecturée. L'optimisation des assemblages a permis d'accroître sensiblement les performances (156 mW.cm-2 à 600 °C). / Materials components for a Proton Conducting Fuel Cell (PCFC) operating in the 400 – 600 °C temperature range have been optimised. Electrolyte material optimisation involved finding the best compromise between chemical stability and conductivity. BaCe0.9Y0.1O2.95, synthesised by flash combustion, exhibits the highest protonic conductivity (10-2 S.cm-1 at 600 °C) but reacts strongly with CO2. Partial substitution of cerium by zirconium (BCZY) and niobium (BCYN30) led to a significant improvement of the chemical stability without drastic effect on the conductivity (5 × 10-3 S.cm-1 at 600 °C). The aim for the electrodes is to develop materials which exhibit high electronic conductivity, sufficient degree of porosity and good mechanical properties. The approach comprised the development of elaboration strategies (one-step synthesis, use of porogen) that allow the control of microstructure in order to minimize area specific resistances (ASR) at the anode. As in the case of SOFCs, cathodic materials are mixed ionic-electronic conductors (MIEC). Development of composite cathodes MIEC-electrolyte led to a significant reduction of ASR. PCFC single cell tests showed that performance was mostly dependent on electrolyte thickness and composition, and on the characteristics of nanostructured electrodes with controlled architecture and porosity. Optimisation of assemblies led to fuel cells performances of 156 mW.cm-2 at 600 °C.

Polymer electrolyte fuel cells (PEFC) convert the chemically bound energy in a fuel, e.g. hydrogen, directly into electricity by an electrochemical process. Examples of future applications are energy conversion such as combined heat and power generation (CHP), zero emission vehicles (ZEV) and consumer electronics. One of the key components in the PEFC is the membrane / electrode assembly (MEA). Both the membrane and the electrodes consist of proton conducting polymers (ionomers). In the membrane, properties such as gas permeability, high proton conductivity and sufficient mechanical and chemical stability are of crucial importance. In the electrodes, the morphology and electrochemical characteristics are strongly affected by the ionomer content. The primary purpose of the present thesis was to develop experimental techniques and to use them to characterise proton conducting polymers and membranes for PEFC applications electrochemically at, or close to, fuel cell operating conditions. The work presented ranges from polymer synthesis to electrochemical characterisation of the MEA performance. The use of a sulfonated dendritic polymer as the acidic component in proton conducting membranes was demonstrated. Proton conducting membranes were prepared by chemical cross-linking or in conjunction with a basic functionalised polymer, PSU-pyridine, to produce acid-base blend membranes. In order to study gas permeability a new in-situ method based on cylindrical microelectrodes was developed. An advantage of this method is that the measurements can be carried out at close to real fuel cell operating conditions, at elevated temperature and a wide range of relative humidities. The durability testing of membranes for use in a polymer electrolyte fuel cell (PEFC) has been studied in situ by a combination of galvanostatic steady-state and electrochemical impedance measurements (EIS). Long-term experiments have been compared to fast ex situ testing in 3 % H2O2 solution. For the direct assessment of membrane degradation, micro-Raman spectroscopy and determination of ion exchange capacity (IEC) have been used. PVDF-based membranes, radiation grafted with styrene and sulfonated, were used as model membranes. The influence of ionomer content on the structure and electrochemical characteristics of Nafion-based PEFC cathodes was also demonstrated. The electrodes were thoroughly investigated using various materials and electrochemical characterisation techniques. Electrodes having medium Nafion contents (35<x<45 wt %) showed the best performance. The mass-transport limitation was essentially due to O2 diffusion in the agglomerates. The performance of cathodes with low Nafion content (<30 wt %) is limited by poor kinetics owing to incomplete wetting of platinum (Pt) by Nafion, by proton migration throughout the cathode as well as by O2 diffusion in the agglomerates. At large Nafion content (>45 wt %), the cathode becomes limited by diffusion of O2 both in the agglomerates and throughout the cathode. Furthermore, models for the membrane coupled with kinetics for the hydrogen electrode, including water concentration dependence, were developed. The models were experimentally validated using a new reference electrode approach. The membrane, as well as the hydrogen anode and cathode characteristics, was studied experimentally using steady-state measurements, current interrupt and EIS. Data obtained with the experiments were in good agreement with the modelled results. / QC 20101014

<p>Polymer electrolyte fuel cells (PEFC) convert the chemically bound energy in a fuel, e.g. hydrogen, directly into electricity by an electrochemical process. Examples of future applications are energy conversion such as combined heat and power generation (CHP), zero emission vehicles (ZEV) and consumer electronics. One of the key components in the PEFC is the membrane / electrode assembly (MEA). Both the membrane and the electrodes consist of proton conducting polymers (ionomers). In the membrane, properties such as gas permeability, high proton conductivity and sufficient mechanical and chemical stability are of crucial importance. In the electrodes, the morphology and electrochemical characteristics are strongly affected by the ionomer content. The primary purpose of the present thesis was to develop experimental techniques and to use them to characterise proton conducting polymers and membranes for PEFC applications electrochemically at, or close to, fuel cell operating conditions. The work presented ranges from polymer synthesis to electrochemical characterisation of the MEA performance.</p><p>The use of a sulfonated dendritic polymer as the acidic component in proton conducting membranes was demonstrated. Proton conducting membranes were prepared by chemical cross-linking or in conjunction with a basic functionalised polymer, PSU-pyridine, to produce acid-base blend membranes. In order to study gas permeability a new in-situ method based on cylindrical microelectrodes was developed. An advantage of this method is that the measurements can be carried out at close to real fuel cell operating conditions, at elevated temperature and a wide range of relative humidities. The durability testing of membranes for use in a polymer electrolyte fuel cell (PEFC) has been studied in situ by a combination of galvanostatic steady-state and electrochemical impedance measurements (EIS). Long-term experiments have been compared to fast ex situ testing in 3 % H2O2 solution. For the direct assessment of membrane degradation, micro-Raman spectroscopy and determination of ion exchange capacity (IEC) have been used. PVDF-based membranes, radiation grafted with styrene and sulfonated, were used as model membranes. The influence of ionomer content on the structure and electrochemical characteristics of Nafion-based PEFC cathodes was also demonstrated. The electrodes were thoroughly investigated using various materials and electrochemical characterisation techniques. Electrodes having medium Nafion contents (35<x<45 wt %) showed the best performance. The mass-transport limitation was essentially due to O2 diffusion in the agglomerates. The performance of cathodes with low Nafion content (<30 wt %) is limited by poor kinetics owing to incomplete wetting of platinum (Pt) by Nafion, by proton migration throughout the cathode as well as by O2 diffusion in the agglomerates. At large Nafion content (>45 wt %), the cathode becomes limited by diffusion of O2 both in the agglomerates and throughout the cathode. Furthermore, models for the membrane coupled with kinetics for the hydrogen electrode, including water concentration dependence, were developed. The models were experimentally validated using a new reference electrode approach. The membrane, as well as the hydrogen anode and cathode characteristics, was studied experimentally using steady-state measurements, current interrupt and EIS. Data obtained with the experiments were in good agreement with the modelled results. Keywords: polymer electrolyte fuel cell, proton conducting membrane, porous electrode, gas permeability, degradation, water transport</p>

The work in this thesis mainly focuses on the preparation and characterization of several phosphates and solid oxide systems with the aim of developing new proton conducting materials for intermediate temperature fuel cells (ITFCs). Soft chemical methods such as sol-gel methods and conventional solid state methods were applied for the synthesis of these materials. Aluminum phosphate obtained by a solution method is single phase and belongs to one of the Al(H₂PO₄)₃ allotropies with hexagonal symmetry. The material is stable up to 200°C and decomposes into Al(PO₃)₃ at a higher temperature. The electrical conductivity of pure Al(H₂PO₄)₃ is on the order of 10⁻⁶-10⁻⁷ S/cm, very close to the value for the known proton conductors AlH₃(PO₄)₂•3H₂O and AlH₂P₃O₁₀•2H₂O. Much higher conductivity is observed for samples containing even a trace amount of excess H₃PO₄. It is likely that the conduction path gradually changes from grain interior to the surface as the acid content increases. The conductivity of Al(H₂PO₄)₃-0.5H₃PO₄ exhibited a good stability over the measured 110 hours. Although tin pyrophosphate (SnP₂O₇) has been reported to show a significantly high conductivity (~10⁻² S/cm) at 250°C in various atmospheres, we observed large discrepancies in the electrical properties of SnP₂O₇ prepared by different methods. Using an excess amount of phosphorous in the synthetic procedure generally produces SnP₂O₇ with much higher conductivity (several orders of magnitude higher) than samples with stoichiometric Sn:P ratios in their synthetic procedure. Solid state ³¹P NMR confirmed the presence of residual phosphoric acid for samples with excess starting phosphorous. Transmission Electron Microscope (TEM) confirmed an amorphous layer covered the SnP₂O₇ granules which was probably phosphoric acid or condensed phases. Thereby, it is quite likely that the high conductivity of SnP₂O₇ results mainly from the contribution of the residual acid. The conductivity of these samples exhibited a good stability over the measured 80 hours. Based on the observations for SnP₂O₇, we developed a nano core-shell structure based on BPO₄ and P₂O₅ synthesised by solid state methods. The particle size of BPO₄ using this method varied between 10-20 nm depending on the content of P₂O₅. TEM confirmed the existence of an amorphous layer that is homogeneously distributed. The composite exhibits the highest conductivity of 8.8×10⁻² S/cm at 300°C in air for 20% extra P₂O₅ and demonstrates a good stability during the whole measured 110 hours. Polytetrafluoroethylene (PTFE) was introduced into the composites in order to increase malleability for fabrication. The conductivity and mechanical strength were optimized by adjusting the PTFE and P₂O₅ content. These organic-inorganic composites demonstrate much better stability at elevated temperature (250°C) over conventional SiC-H₃PO₄-PTFE composites which are common electrolytes for phosphoric acid fuel cells (PAFCs). Fuel cells based on BPO₄-H₃PO₄-PTFE composite as the electrolyte were investigated using pure H₂ and methanol as fuels. A maximum power density of 320 mW/cm² at a voltage of 0.31 V and a maximum current density of 1.9 A/cm² at 200°C were observed for H₂/O₂ fuel cells. A maximum power density of 40 mW/cm² and maximum current of 300 mA/cm² 275°C were observed when 3M methanol was used in the cell. Phosphoric acid was also introduced into materials with internal open structures such as phosphotungstic acid (H₃PW₁₂O₄₀) and heteropolyacid salt ((NH₄)₃PW₁₂O₄₀), for the purpose of acquiring additional connections. The hybrids obtained have a cubic symmetry with enlarged unit cell volume, probably due to the incorporation of phosphoric acid into the internal structures. Solid state ³¹P NMR performed on H₃PW₁₂O₄₀-xH₃PO₄ (x = 0-3) showed additional peaks at high acid content which could not assigned to phosphorus from the starting materials, suggesting a strong interaction between H₃PW₁₂O₄₀ and H₃PO₄. The conductivity of hybrids was improved significantly compared with samples without phosphoric acid. Fourier transform infrared spectra (FT-IR) suggest the existence of large amount of hydrogen bonds (OH••••O) that may responsible for the high conductivity. A H₂/O₂ fuel cell based on H₃PW₁₂O₄₀-H₃PO₄-PTFE exhibited a peak power density of 2.7 mW/cm² at 0.3 V in ambient temperature. Solid oxide proton conductors based on yttrium doped BaZrO₃ were investigated by introducing potassium or lanthanum at the A-sites. The materials were prepared by different methods and were obtained as a single phase with space group Pm-3m (221). The unit cell of these samples is slightly smaller than the undoped one. The upper limit of solid solution formation on the A-sites for potassium is between 5 ~ 10% as introducing more K results in the occurrence of a second phase or impurities such as YSZ (yttrium stabilized zirconium). K doped Barium zirconates showed an improved water uptake capability even with 5% K doping, whereas for La doped ones, water uptake is strongly dependent on particle size and synthetic history. The conductivity of K doped BaZrO₃ was improved by a factor of two (2×10⁻³ S/cm) at 600°C compared with undoped material. Fuel cells based on Pt/Ba₀₋₉₅K₀₋₀₅Zr₀₋₈₅Y₀₋₁₁Zn₀₋₀₄O[subscript(3-δ)]/Pt under humidified 5% H₂/air conditions gave a maximum power density 7.7 mWcm⁻² at 718°C and an interfacial resistance 4 Ωcm⁻². While for La doped samples, the conductivity was comparable with undoped ones; the benefits of introducing lanthanum at A-sites may not be so obvious as deficiency of barium is one factor that leads to the diminishing conductivity.