Nanofibres are useful in a broad range of applications in areas such as medical science, food science, materials engineering, environmental engineering, and energy and electronics due to their outstanding characteristics: their small size, high surface-to-volume ratio, high porosity, and superior mechanical performance. Recently, controlled drug delivery systems have gained significant attention, especially with respect to the use of polymer nanofibres. For these systems, the ability to control of the length of the polymer nanofibre is important because the amount of drug released depends on the length of the fibre. Electrospinning is the simplest and most cost-effective method of fabricating polymer nanofibres. In the process, a high voltage is used to create an electrified jet which will eventually become a nanofibre. The electrified jet ejects when a high voltage is applied to the electrospinning setup. On the other hand, the jet does not eject when the applied voltage is below the threshold voltage. It is therefore possible to fabricate and chop nanofibres by controlling the values of the voltages applied and a special high-voltage pulsed power supply has been developed for this purpose. In this research, an IGBT-based pulsed power supply has been designed and built to be used for non-continuous-mode electrospinning. The IGBTs are connected in series to deliver high voltage pulse voltages to an electrospinning setup. The IGBT-based pulsed power supply is capable of producing controllable square pulses with a width of a few hundred microseconds to DC and amplitudes up to 10 kV. The technique of non-continuous-mode electrospinning was tested using the pulsed power supply designed in this work. The new system was able to fabricate and chop nanofibres with PEO and alginate/PEO solutions. It was concluded that the minimum pulse width that can initiate an electrified jet is approximately 80 ms for the parameters used in this study. A longer period produces a more constant jet during the pulse-on voltage when the duty ratio is the same value. It is also highly likely that a jet is always ejected during the pulse-on voltage when the duty ratio is more than 40 %.

Thesis (M.S. in Electrical Engineering)--Naval Postgraduate School, December 2009. / Thesis Advisor(s): Julian, Alexander L. Second Reader: Crisiti, Roberto. "December 2009." Description based on title screen as viewed on January 28, 2010. Author(s) subject terms: Pulsed power, charger, buck converter, field programmable gate array (FPGA), lithium-ion batteries. Includes bibliographical references (p. 77-79). Also available in print.

Thesis (M.S.)--Worcester Polytechnic Institute. / Keywords: Langmuir probes; spacecraft; electric propulsion. Includes bibliographical references (p.69-71).

The interaction of ultra-short laser pulses and cluster targets can be used to explore a number of interesting phenomena, ranging from nuclear fusion to astrophysical blast waves. In our experiments, we focused on exploring very fast plasma dynamics of a plasma created by ionizing clusters and monomer gas. By using a 115 fs laser pulse, we can even study sub-picosecond plasma dynamics. In addition, we also wanted to impose an external magnetic field on these plasmas to study how the plasma evolution would change. The results of this work produced two significant results. First, a new, extremely fast ionization mechanism, with velocities as high as 0.5 c, was discovered which allows for significant plasma expansion on a picosecond time-scale. Experimental studies measured the velocity of the ionization wave, while particle-in-cell simulations helped explain the source and longevity of the wave. It was also observed that this ionization wave was not affected by the external magnetic field. Second, the external field was shown to inhibit plasma expansion on a time-scale of tens of picoseconds, which seems to be one of the first demonstrations of magnetic confinement on such a fast time-scale. Simple 1D simulations tell us that the field appears to slow electron heat transport in the plasma as well as inhibiting collisional ionization of electrons expanding into the surrounding gas. The inhibition of plasma expansion by the field on this time-scale may provide some evidence that magnetic confinement of a fusion plasma created by exploding clusters could improve the fusion yield by slowing heat loss as well as possibly electrostatically confining the hot ions. / text

Thesis (Ph. D.)--Missouri University of Science and Technology, 2008. / Vita. The entire thesis text is included in file. Title from title screen of thesis/dissertation PDF file (viewed April 21, 2008) Includes bibliographical references.

Thesis (M.S.)--Auburn University, 2008. / Abstract. Vita. Includes bibliographical references (p. 55-57).

The use of high-powered electrical energy systems requires an efficient and capable means to move electrical energy from one location to another while reducing energy losses. This paper describes the design and construction process of a high-powered busbar system that is to be implemented in pulsed-power applications. In order to obtain a robust system capable of handling in excess of 25kJ, both mechanical and electrical analyses were performed to verify a capable design. The following methodology describes how the Lorentz force was balanced with mechanical forces during the design process and then validated after construction was completed using the fundamental Maxwell equations and computer simulations. Main focuses include handling of EMF, high current density concentrations, and overall mechanical stability of the system and how these effects determine the physical design and implementation. In the end, a repeatable methodology is presented in the form of a design process that can be implemented in any system given the design criteria. / Master of Science

The current driven electrothermal instability (ETI) forms when the material resistivity is temperature dependent, occurring in nearly all Z-pinch-like high energy density platforms. ETI growth for high-mass density materials is predominantly striation form which corresponds to magnetically perpendicular mode growth. The striation form is caused by a resistivity that increases with temperature, which is often the case for high-mass density materials. In contrast, low-density ETI growth is mainly filamentation form, magnetically aligned modes, because the resistivity tends to decrease with temperature. Simulating ETI is challenging due to the coupling of magnetic field transport to equation of state over a large region of state space spanning solids to plasmas. This dissertation presents a code-code verification study to effectively model the ETI. Specifically, this study provides verification cases which ensure the unit physics components essential to modeling ETI are accurate. This provides a way for fluid-based codes to simulate linear and nonlinear ETI. Additionally, the study provides a sensitivity analysis of nonlinear ETI to equation of state, vacuum resistivity, and vacuum density. Simulations of ETI typically use a collisional form of the resistivity as provided, e.g., in a Lee-More Desjarlais conductivity table. In regions of low-mass density, collision-less transport needs to be incorporated to properly simulate the filamentation form of ETI growth. Anomalous resistivity (AR) is an avenue by which these collision-less micro-turbulent effects can be incorporated into a collisional resistivity. AR directly changes the resistivity which will directly modify the linear growth rate of ETI, so a new linear growth rate is derived which includes AR's added dependency on current density. This linear growth rate is verified through a filamentation ETI simulation using an ion acoustic based AR model. Kinetically based simulations of vacuum contaminant plasmas provide a physical platform to study the use of AR models in pulsed-power platforms. Using parameters from the Z-machine pulsed-power device, the incorporation of AR can increase a collisional-based resistivity by upwards of four orders of magnitude. The presence of current-carrying vacuum contaminant plasmas can indirectly affect nonlinear ETI growth through modification of the magnetic diffusion wave. The impact of AR on nonlinear ETI is explored through pulsed-power simulations of a dielectrically coated solid metallic liner surrounded by a low-density vacuum contaminant plasma. / Doctor of Philosophy / High-energy-density physics (HEDP) is the study of materials with pressures that exceed 1Mbar, and is difficult to reach here on Earth. Inertial confinement fusion concepts and experiments are the primary source for achieving these pressures in the laboratory. Inertial confinement fusion (ICF) is a nuclear fusion concept that relies on the inertia of imploding materials to compress a light fuel (often deuterium and tritium) to high densities and temperatures to achieve fusion reactions. The imploding materials in ICF are driven in many ways, but this dissertation focuses on ICF implosions driven by pulsed-power devices. Pulsed-power involves delivering large amounts of capacitive energy in the form of electrical current over very short time scales (nanosecond timescale). The largest pulsed-power driver is the Z-machine at Sandia National Laboratory (SNL) which is capable of delivering upwards of 30 MA in 130 ns approximately. During an ICF implosion there exists instabilities that disrupt the integrity of the implosion causing non-ideal lower density and temperature yields. One such instability is the Rayleigh-Taylor instability where a light fluid supports a heavy fluid under the influence of gravity. The Rayleigh-Taylor is one of the most detrimental instabilities toward achieving ignition and was one of the main research topics in the early stages of this Ph.D. The study of this instability provided a nice intro for modeling in the HEDP regime, specifically, in the uses of tabulated equations-of-state and tabulated transport coefficients (e.g., resistivity and thermal conductivity). The magneto Rayleigh-Taylor instability occurs in pulsed-power fusion platforms where the heavy fluid is now supported by a magnetic field instead of a light fluid. The magneto Rayleigh-Taylor instability is the most destructive instability in many pulsed-power fusion platforms, so understanding seeding mechanisms is critical in mitigating its impact. Magnetized liner inertial fusion (MagLIF) is a pulsed-power fusion concept that involves imploding a solid cylindrical metal annulus on laser-induced pre-magnetized fuel. The solid metal liners have imperfections and defects littered throughout the surface. The imperfections on the surface create a perturbation during the initial phases of the implosion when the solid metal liner is undergoing ohmic heating. Because a solid metal has a resistivity that increases with temperature, as the metal heats the resistivity increases causing more heating which creates a positive feedback loop. This positive feedback loop is similar to the heating process in a nichrome wire in a toaster, and is the fundamental bases of the main instability studied in this dissertation, the electrothermal instability (ETI). ETI is present in all pulsed-power fusion platforms where a current-carrying material has a resistivity that changes with temperature. In MagLIF, ETI is dominant in the early stages of a current pulse where the resistivity of the metal increases with temperature. An increasing resistivity with temperature is connected to the axially growing modes of ETI which is denoted as the striation form of ETI. Contrary to the striation form of ETI, the filamentation form of ETI occurs when resistivity decreases with temperature and is associated with the azimuthally growing modes of ETI. Chapter 2 in this dissertation details a study of how to simulate striaiton ETI for a MagLIF-like configuration across different resistive magnetohydrodynamics (MHD) codes. Resistivity that decreases with temperature typically occurs in low-density materials which are often in a gaseous or plasma state. Low density plasmas are nearly collision-less and have resistivity definitions that often overestimate the conductivity of a plasma in certain experiments. Anomalous resistivity (AR) addresses this overestimation by increasing a collisional resistivity through micro-turbulence driven plasma phenomenon that mimic collisional behavior. The creation of AR involves reduced-modeling of micro-turbulence driven plasma phenomenon, such as the lower hybrid drift instability, to construct an effective collision frequency based on drift speeds. Because AR directly modifies a collisional resistivity for certain conditions, it will directly alter the growth of ETI which is the topic of Chapter 3. The current on the Z-machine is driven by the capacitor bank through the post-hole convolute, the magnetically insulated transmission lines, and then into the chamber. Magnetically insulated transmission lines have been shown to create low-density plasma through desorption processes in the vacuum leading to a load surrounded by a low-density plasma referred to as a vacuum contaminant plasmas (VCP). VCP can divert current from the load by causing a short between the vacuum anode and cathode gap. In simulations, this plasma would be highly conducting when represented by a collisionally-based resistivity model resulting in non-physical vacuum heating that is not observed in experiments. VCP are current-carrying low-density and high-temperature plasmas which make them ideal candidates to study the role of AR as described in Chapter 4. Chapter 4 investigates the role AR in a VCP would have on striation ETI for a MagLIF-like load.

The growing demand for high voltage, compact pulsed power supplies has gained great attention. It requires power supplies with high power density, low profile and high efficiency. In this thesis, topologies and techniques are investigated to meet and exceed these challenges. Non-isolation type topologies have been used for this application. Due to the high voltage stress of the output, non-isolation topologies will suffer severe loss problems. Extremely low switching frequency will lead to massive magnetic volume. For non-isolation topologies, PWM converters can achieve soft switching to increase switching frequency. However, for this application, due to the large voltage regulation range and high voltage transformer nonidealities, it is difficult to optimize PWM converters. Secondary diode reverse recovery is another significant issue for PWM techniques. Resonant converters can achieve ZCS or ZVS and result in very low switching loss, thus enabling power supplies to operate at high switching frequency. Furthermore, the PRC and LCC resonant converter can fully absorb the leakage inductance and parasitic capacitance. With a capacitive output filter, the secondary diode will achieve natural turn-off and overcome reverse recovery problems. With a three-level structure, low voltage MOSFETs can be applied for this application. Switching frequency is increased to 200 kHz. In this paper, the power factor concept for resonant converters is proposed and analyzed. Based on this concept, a new methodology to measure the performance of resonant converters is presented. The optimal design guideline is provided. A novel constant power factor control is proposed and studied. Based on this control scheme, the performance of the resonant converter will be improved significantly. Design trade-offs are analyzed and studied. The optimal design aiming to increase the power density is investigated. The parallel resonant converter is proven to be the optimum topology for this application. The power density of 31 W/inch3 can be achieved by using the PRC topology with the constant power factor control. / Master of Science

State-of-Health (SoH), a specified measure of stability, is a critical parameter for determining the safe operating area of a battery cell and battery packs to avoid abuse and prevent failure and accidents. A series of experiments were performed to evaluate the performance of a 4P1S battery array using electrochemical impedance spectroscopy to identify key frequencies that may describe battery state of health at any state of charge. Using a large sample number of cells, the state of health frequency, fSoH, for these LiFePO4 26650 cells is found to be 158 Hz. Four experiments were performed to evaluate the lifetime in different configurations: single-cell at 1C (2.6A), single-cell at 10C (26A), four cells in parallel at 10C (ideal match), and four cells in parallel (manufacturer match). The lifetime for each experiment set degraded substantially, with the final parallel series reaching end of life at 400 cycles, a 75.32% reduction in life compared to operating solo. Analysis of the fSoH data for these cells revealed a change in imaginary impedance at the critical frequency that corresponded to changes in the capacity and current data, supporting the development of a single-frequency diagnostic tool. An electrochemical model of the battery was generated, and it indicated the anode material was aging faster than the SEI layer, the opposite of normal cell degradation. A post-mortem analysis of cells from three configurations (baseline, single-cell, and parallel-cell) supported the modeling, as physical damage to the copper current collector in the anode was visible in the parallel-connected cell. / Ph. D.