Reflectarrays are traditionally passive, planar microstrip antenna devices designed for reflected phase manipulation at each individual antenna element making up the array. By varying the phase response across the surface with the antenna elements, reflectarrays allows a planar surface to exhibit electromagnetically an arbitrary geometry, such as a spherical surface. Initially proposed as a low-cost replacement for bulky parabolic reflectors, reflectarrays have been successfully developed and utilized at both RF and millimeter-wave frequencies. From the standpoint of an optical systems designer, adapting low-frequency reflectarray technology to develop a sub-millimeter and infrared reflectarray (SMIR) would provide a highly desirable alternative to similarly behaved polished or diffractive optical devices. Compared to traditional optical reflectors, SMIRs should be cheaper to fabricate, have a smaller physical footprint, allow for utility stacking, and encourage direct integration of aberration correction. To demonstrate the feasibility of utilizing reflectarray technology at infrared (IR), a simple SMIR proof of concept has been successfully designed, fabricated, and tested. The SMIR is comprised of three independent arrays or "stripes" of a single size element on a coated optical flat. Actual reflectarray elements consist of variable size patches that exhibit higher operating bandwidths than reflectarrays utilizing other types of elements and are easier to fabricate at small dimensions. For testing, each stripe element has been chosen to exhibit a unique phase shift for measurement using an IR interferometer. Preliminary investigation of future reflectarray development is also discussed. Emphasis is placed on improving operating bandwidth, development of a planar focusing element, and aberration correction. With further development, SMIR technology should present a powerful tool for low cost, flexible optical system design.

No description available.

In the past decade, artificial materials have attracted considerable attention as potential solutions to meet the demands of modern microwave technology for simultaneously achieving component minimization and higher performance in mobile communications, medical, and optoelectronics applications. To realize this potential, more research on metamaterials is needed. In this dissertation, new bandpass filter and diplexer as microwave metamaterial applications have been developed. Unlike the conventional complementary split ring (CSRR) filters, coupled lines are used to provide larger coupling capacitance, resulting in better bandpass characteristics with two CSRRs only. The modified bandpass filters are used to deisgn a compact diplexer. A new CSRR antenna fed by coplanar waveguide has also been developed as another metamaterial application. The rectangular shape CSRRs antenna achieves dual band frequency properties without any special matching network. The higher resonant frequency is dominantly determined by the outer slot ring, while the lower resonant frequency is generated by the coupling between two CSRRs. The proposed antenna achieves about 35 percent size reduction, compared with the conventional slot antennas at the low resonant frequencies. As a future alternative energy solution, space solar power transmission and wireless power transmission have received much attention. The design of efficient rectifying antennas called rectennas is very critical in the wireless power transmission system. The conventional method to obtain long distance range and high output power is to use a large antenna array in rectenna design. However, the use of array antennas has several problems: the relatively high loss of the array feed networks, difficultiy in feeding network design, and antenna radiator coupling that degrades rectenna array performance. In this dissertation, to overcome the above problems, a reflectarray is used to build a rectenna system. The spatial feeding method of the reflectarray eliminates the energy loss and design complexity of a feeding network. A high gain rectifying antenna has been developed and located at the focal point of the reflectarray to receive the reflected RF singals and genterate DC power. The technologies are very useful for high power wireless power transmission applications.

In this thesis 10x10 reconfigurable reflectarray is designed at 26.5 GHz where the change in the progressive phase shift between elements is obtained with RF MEMS switches in the transmission lines of unit elements composed of aperture coupled microstrip patch antenna (ACMPA). The reflectarray is illuminated by a horn antenna, and the reflected beam is designed to switch between broadside and 40&deg / by considering the position of the horn antenna with respect to the reflectarray. In the design, the transmission line analysis is applied for matching the ACMPA to the free space. The full wave simulation techniques in HFSS are discussed to obtain the phase design curve which is used in determining two sets of transmission line lengths for each element, one for the broadside and the other for switching to the 40&deg / at 26.5 GHz. The switching between two sets of transmission line lengths is sustained by inserting RF MEMS switches into the transmission lines in each element. Two types of RF MEMS switches, series and shunt configurations, are designed for the switching purpose in the reflectarray. The phase errors due to nonideal phase design curve and type of the RF MEMS switch are reduced. The possible mutual coupling effects of the bias lines used to actuate the RF MEMS switches are also eliminated by the proper design. To show the validity of the design procedure, a prototype of 20x20 reflectarray composed of ACMPA elements is designed at 25GHz and produced using Printed Circuit Board (PCB) technology. The measurement results of the prototype reflectarray show that the main beam can be directed to the 40&deg / as desired. The process flow for the production of the reconfigurable reflectarray is suggested in terms of integration of the wafer bonding step with the in-house standard surface micromachined RF MEMS process.

There has been a rapid growth of terrestrial and satellite communications in the last few decades of the 20th century. This has resulted in a heavy congestion of low microwave bands and has been a major driving force for exploring the upper microwave and millimeter-wave frequencies. One of the main requirements for a successful shift to the new frequency spectrum is the availability of high power solid-state transmitters. Solid-state devices such as diodes or transistors have been able to meet such demands when their output signals are combined using space-level power combining methods that avoid conduction losses, which become pronounced at millimeter wave frequencies. In this thesis, theoretical and experimental investigations are carried out into the spatial power combiners (SPCs) which employ active planar arrays formed by transistor amplifiers whose input and output ports are equipped with planar radiating elements. The SPC structures include the reflection-type combiner using the tile configuration of planar array and the transmission-type combiner using tile or tray configurations of planar arrays. The frequency bands chosen for the designing and testing of prototypes are X- and Ku-band. The first stage of the investigation concerns the 10 GHz reflection-type power combiner structure formed by a phased planar microstrip reflectarray (MRA) of 37-element dual-feed aperture coupled microstrip patch antennas equipped with open-circuit stubs as phasing components. The experimental tests reveal poor radiation performance and hence poor power combining efficiency of this structure. These results indicated the need for theoretical investigations into the operation of this type of SPC. The study of the unit cell of this power combiner reveals that the phase of an open-circuit stub does not increase linearly as a function of the stub length and its range is limited to less than (about is required for proper functioning). This finding, forms the basis for extending the investigations into alternative phasing mechanisms of a MRA which would offer a phasing range exceeding . A phasing mechanism exploiting variable size stacked patches is chosen. In order to accurately determine the phasing of the reflected wave, a theory based on an equivalent unit cell waveguide approach (WGA) is proposed and developed. The proposed theory is computationally efficient and is proven to be accurate compared with benchmark results published by other researchers. Following the verification, an offset feed 161-element two-layer printed MRA prototype with patches of variable size is designed and developed for operation in Ku-band. The test results aim at verifying the validity of applying a unit cell WGA to designing passive and active MRAs. The next investigations, which are presented in the thesis concern increasing operational bandwidth of the transmission-type SPC in tile configuration. The designs presented so far in the open literatures were based on edge-feed microstrip patch antennas as radiating elements of individual active stages and featured a narrow-band performance. In order to overcome this shortcoming, stacked patch (SP) microstrip antennas as receiving and transmitting elements in an active transmitarray (TXA) are proposed. For the aim of testing the proposed concept, a 16-element SP TXA is designed for operation in X-band. Two identical hard horn antennas with an approximately uniform field across the aperture for signal launching and collecting complete the design and development of this space-level power combiner. The performance of the developed device is assessed experimentally and an increased operational bandwidth is demonstrated. The final structure being investigated in the thesis project is the transmission-type SPC in tray configuration. This power combining structure employs a travelling wave antenna of uniplanar quasi-Yagi type as a radiating element to achieve broad-band operation. The investigated SPC is formed by seven trays of uniplanar quasi-Yagi antenna. In order to achieve uniform and in-phase excitation of individual trays, which is required to obtain high power combining efficiency, hard horn antennas and Schiffman phase shifters are employed in the design of this space-level combiner. The proposed device is developed and its performance is assessed through experiments. The work performed as part of this Ph.D. thesis project has resulted in 5 journal papers and 11 refereed conference papers. This acceptance rate supports the claim of the originality and significance of the research undertaken as part of the thesis project.

This dissertation research presents a comprehensive study to answer the question of “Can it be possible to integrate a high gain optically transparent antenna array directly on top of solar cells?”. The answer to such question is extremely important in space exploration where very small satellites have been extensively employed. Due to their small mass and size, those small satellites create challenges for one to mount the antennas, and the challenge is further increased when a high gain antenna is need for more communication capacity. Based on feasibility studies, the dissertation concludes that it is possible to do such an integration, and then proceeds to present the approaches for design and integration. On the element level, the thesis presents research in assessing the effects between a planar antenna integrated on the solar cell and the photovoltaic cell. A series of experiments were designed to perform assessments for antennas operating from C to X bands. It is concluded that a commercial triple junction space–certified solar cell normally would decrease the gain of the antenna to 2–3 dB and is not affected by the working states of solar cells. The shadow of the antenna casts on solar cells, however, is not significant (less than 2%). The thesis also provides a model of a common space solar cell that helps to explain the gain loss. The model was validated by experimental data, and it was utilized to predict iv a possible custom design of solar cell where with a minimal design modification, it would facilitate less gain loss of the antenna integrated on top. On the array level, the research surveys different high gain antenna array design and then focus on an optimal sub–wavelength reflectarray design. The final antenna array design is a 30 cm by 20 cm, X band (8.475 GHz) reflectarray that shows 94% transparency, 24 dB gain, and higher than 40% aperture efficiency. The design is then prototyped and tested on actual solar panel. The measurement of the reflectarray placed on the solar panel showed a gain of 22.46 dB and an aperture efficiency of 29.3%. While those results are considered excellent, the thesis continues to address the reasons for reduction of the antenna’s performance due to the solar panel, through both theoretical analysis and experiments.

Reflectarrays are passive quasi-periodic sub-wavelength antenna arrays designed for discrete reflected phase manipulation at each individual antenna element making up the array. By spatially varying the phase response of the antenna array, reflectarrays allow a planar surface to impress a non-planar phasefront upon re-radiation. Such devices have become commonplace at radio frequencies. In this dissertation, they are demonstrated in the infrared for the first time--at frequencies as high as 194 THz. Relevant aspects of computational electromagnetic modeling are explored, to yield design procedures optimized for these high frequencies. Modeling is also utilized to demonstrate the phase response of a generalized metallic patch resonator in terms of its dependence on element dimensions, surrounding materials, angle of incidence, and frequency. The impact of realistic dispersion of the real and imaginary parts of the metallic permittivity on the magnitude and bandwidth of the resonance behavior is thoroughly investigated. Several single-phase reflectarrays are fabricated and measurement techniques are developed for evaluating these surfaces. In all of these cases, there is excellent agreement between the computational model results and the measured device characteristics. With accurate modeling and measurement, it is possible to proceed to explore some specific device architectures appropriate for focusing reflectarrays, including binary-phase and phase-incremental approaches. Image quality aspects of these focusing reflectarrays are considered from geometrical and chromatic-aberration perspectives. The dissertation concludes by briefly considering two additional analogous devices--the transmitarray for tailoring transmissive phase response, and the emitarray for angular control of thermally emitted radiation.

X BAND TWO LAYER PRINTED REFLECTARRAY WITH SHAPED BEAM &Uuml / &ccedil / &uuml / nc&uuml / , G&ouml / khan MSc., Department of Electrical and Electronics Engineering Supervisor: Prof. Dr. H. &Ouml / zlem Aydin &Ccedil / ivi October, 2011, 110 pages X-band cosecant square shaped beam microstrip reflectarray is designed, fabricated and measured. Unit element of the reflectarray is in stacked patch configuration. With the aim of designing shaped beam pattern, phase-only synthesis method based on genetic algorithm is used. Phases of reflected electric field from antenna elements are adjusted by changing the dimensions of the patches. Unit cell simulations are performed using periodic boundary conditions and assuming infinite array approach to obtain reflection phase curves versus patch size. Then full reflectarray surface and its feed are designed and fabricated. Radiation patterns are measured in spherical near field range and results are compared with simulations. It is shown that the antenna is capable to operate in a band of 8.6 - 9.7 GHz.

L’objectif de cette thèse est de concevoir un réseau réflecteur à dépointage électronique à 20 GHz pour des applications de communication avec des drones (Unmanned Aerial System). Le principe de fonctionnement des réseaux réflecteurs est similaire à celui d’une antenne parabolique. La principale différence concerne la forme du réflecteur. En effet les panneaux des réseaux réflecteurs sont plans contrairement à la parabole. Le panneau réflecteur se compose de cellules élémentaires qui sont utilisées pour contrôler la phase réfléchie de l’onde d’incidente. Le contrôle de la phase au niveau de la cellule élémentaire nous permet de focaliser le diagramme de rayonnement dans la direction souhaitée. Dans cette thèse, la solution retenue est l’utilisation de diodes PIN. Cette dernière a fait l’objet de nombreuses études que ce soit au niveau laboratoire mais également industriel et possède des atouts intéressant en terme de performance et de coût. L'étude montre que d'avoir un niveau de correction élevée ne garantit pas la meilleure performance parce qu'il faut aussi considérer les pertes dans l'élément actif lui-même (dans notre cas, il s’agit des pertes dans les diodes PIN). Dans l’avenir, il serait nécessaire de modifier la position de la diode afin de rendre la fabrication plus aisée. Dans ce cas il faudra retravailler sur les lignes de polarisation et aussi les géométries du stub et des vias. Il sera peut-être nécessaire de déplacer la diode à l'extérieur du substrat en face l'arrière de la cellule par exemple. Quand les réseaux réflecteurs seront fabriqués, ils pourront être directement testés avec le contrôleur de diode fabriqué. / The objective of this project is to design and fabricate a reconfigurable reflectarray with beam scanning capability at 20 GHz for unmanned aerial system (UAS) communication link. Reflectarray is a type of antenna that shares similar functionality to parabolic reflector antenna. The main difference is the physical and geometry appearance of the antenna where reflectarray has flat reflecting panel instead of parabolic reflector. The reflecting panel consists of elementary cell, which is used to control the reflected phase of the incident wave. By controlling the reflected phase on each elementary cell, the radiation pattern of the antenna can be focused to any desired direction. PIN diode technology is chosen as the preferred solution in the context of this project because it is already proven working in the industry and research fields. In house reflectarray simulator has been developed from the simulation, having high correction order will not necessarily improve the performance because the loss inside in active element must also be considered. In the short-term period, the modification on the elementary cell diode polarization line will enable the reflectarray to be fabricated and measured because the current design cannot be fabricated by the manufacturer contrary to their first statement due to position of the diode in the middle of substrates. The modification requires the p-i-n diode to be moved at the backside of the elementary cell and some geometry adjustments are needed for the phase delay line and the via. Once the reflectarray is fabricated, it can be tested directly with the diode controller that is already validated and shown to be working well.

Reflectarray antennas uniquely combine the advantages of parabolic reflectors and phased array antennas. Comprised of planar structures similar to phased arrays and utilizing quasi-optical excitation similar to parabolic reflectors, reflectarray antennas provide beam steering without the need of complex and lossy feed networks. Chapter 1 discusses the basic theory of reflectarray and its design. A brief summary of previous work and current research status is also presented. The inherent advantages and drawbacks of the reflectarray are discussed. In chapter 2, a novel theoretical approach to extract the reflection coefficient of reflectarray unit cells is developed. The approach is applied to single-resonance unit cell elements under normal and waveguide incidences. The developed theory is also utilized to understand the difference between the TEM and TE10 mode of excitation. Using this theory, effects of different physical parameters on reflection properties of unit cells are studied without the need of full-wave simulations. Detailed analysis is performed for Ka-band reflectarray unit cells and verified by full-wave simulations. In addition, an approach to extract the Q factors using full-wave simulations is also presented. Lastly, a detailed study on the effects of inter-element spacing is discussed. Q factor theory discussed in chapter 2 is extended to account for the varying incidence angles and polarizations in chapter 3 utilizing Floquet modes. Emphasis is laid on elements located on planes where extremities in performance tend to occur. The antenna element properties are assessed in terms of maximum reflection loss and slope of the reflection phase. A thorough analysis is performed at Ka band and the results obtained are verified using full-wave simulations. Reflection coefficients over a 749-element reflectarray aperture for a broadside radiation pattern are presented for a couple of cases and the effects of coupling conditions in conjunction with incidence angles are demonstrated. The presented theory provides explicit physical intuition and guidelines for efficient and accurate reflectarray design. In chapter 4, tunable reflectarray elements capacitively loaded with Barium Strontium Titanate (BST) thin film are shown. The effects of substrate thickness, operating frequency and deposition pressure are shown utilizing coupling conditions and the performance is optimized. To ensure minimum affects from biasing, optimized biasing schemes are discussed. The proposed unit cells are fabricated and measured, demonstrating the reconfigurability by varying the applied E-field. To demonstrate the concept, a 45 element array is also designed and fabricated. Using anechoic chamber measurements, far-field patterns are obtained and a beam scan up to 25o is shown on the E-plane. Overall, novel theoretical approaches to analyze the reflection properties of the reflectarray elements using Q factors are developed. The proposed theoretical models provide valuable physical insight utilizing coupling conditions and aid in efficient reflectarray design. In addition, for the first time a continuously tunable reflectarray operating at Ka-band is presented using BST technology. Due to monolithic integration, the technique can be extended to higher frequencies such as V-band and above.