No description available.

No description available.

No description available.

Dielectric constant is a physical property of soil that is often measured using non-invasive geophysical techniques in subsurface characterization studies. A proper understanding of dielectric responses allows investigators to make measurements that might otherwise require more invasive and/or destructive methods. Previous studies have suggested that dielectric models could be refined by accounting for the contributions of different types of mineral constituents that affect the ratio and properties of bound and bulk water. This study tested the hypothesis that the dielectric responses of porous materials are mineral-specific through differences in surface area and chemistry. An experimental design was developed to test the dielectric behavior of pure quartz sand (Control), quartz sand/kaolin clay mixtures and ferric oxyhydroxide coated quartz sand. Results from the experiments show that the dielectric responses of quartz-clay and iron oxyhydroxide modified samples are not significantly different from the pure quartz Control. Increasing clay content in quartz sands leads to a vertical displacement between fitted polynomials. The results suggest that the classic interpretation for the curvature of dielectric responses appears to be incorrect. The curvature of dielectric responses at low water contents appears to be controlled by unknown parameters other than bound water. A re-examination of the experimental procedure proposed in this study and past studies shows that a properly designed study of bound water effects on dielectric responses has not yet been conduct / Master of Science

Black coatings essentially absorb incident light at all wavelengths from all directions. They are used when minimal reflection or maximum absorption is desired and therefore are effective in applications that require control of stray light. Our motivation stems from the use of black coating Lord Aeroglaze® Z302 in aerospace and remote sensing applications and the desire to support the development of bidirectional spectral models that can be used successfully to predict the performance of optical instruments such as telescopes. The bidirectional reflectance distribution function (BRDF) is an indispensable parameter in the optical characterization of such coatings. The current effort involves investigation of the BRDF of the commercial black coating Aeroglaze® Z302. An automated goniometer reflectometer has been designed, fabricated and successfully used for performing the BRDF measurements of Z302 at visible and ultraviolet wavelengths and at both polarizations. The current contribution involves study of Z302 samples prepared at different thicknesses and by different methods, which provides insight about influence of surface roughness on BRDF of Z302. / Master of Science / When light falls on different materials it undergoes various phenomenon such as reflection, refraction, absorption and scattering. The amount of each phenomenon varies with the optical nature of a material as well as the wavelength and direction of the light. Therefore, understanding the optical properties of materials at various wavelengths of light is necessary for effectively using those materialsin specific applications which require light to be efficiently reflected or absorbed. This research studies an optical property known as Bidirectional Reflectance Distribution Function (BRDF) of a black coating called Lord Aeroglaze Z302. Black coatings are materials that ideally absorb almost all light that falls on them irrespective of the light’s direction and wavelength. They are used in applications where maximum absorption of light is required. One such application which relates to the motivation for this research is absorbing unwanted light in instruments used in space such as telescopes and radiometers. Z302 is used in the Clouds and the Earth’s Radiant Energy System (CERES) instruments developed by NASA. BRDF is an important parameter which gives information about all other optical properties of a surface and can be used to know optical performance of that surface. The current work describes the experiments and an automated device developed, called reflectometer, to measure the BRDF of Z302 at different angles and wavelengths of light. The results are reported for different thickness samples of Z302 coating, and two different wavelengths of light that belong to the visible and ultraviolet spectrum of light.

The National Aeronautics and Space Administration’s (NASA) Cyclone Global Navigation Satellite System (CYGNSS) mission has grown substantial attention within the land remote sensing community for estimating soil moisture (SM), wind speed, flood extent, and precipitation by using the Global Navigation Satellite System-Reflectometry (GNSS-R) technique. CYGNSS constellation generates important earth surface information called Delay-Doppler Maps (DDMs) from GNSS reflection measurements. Many previous findings considered only designed features from CYGNSS DDMs, such as the peak value of DDMs, whereas the whole DDMs are affected by SM, topography, inundation, and overlying vegetation. This dissertation explores a deep learning approach for estimating SM by leveraging spaceborne GNSS-RDDM observations provided by the CYGNSS constellation along with other remotely sensed geophysical data products. A data-driven approach utilizing convolutional neural networks (CNNs) that is trained jointly with three types of processed DDMs of Analog Power, Effective scattering area, and Bistatic Radar Cross-section (BRCS) with other auxiliary geophysical information such as normalized difference vegetation index (NDVI), elevation, soil properties, and vegetation water content (VWC). The model is trained and evaluated using the Soil Moisture Active Passive (SMAP) mission’s enhanced SM products at a 9km × 9km resolution. The model is also evaluated using in-situ measurements from International Soil Moisture Network (ISMN). The proposed approach is first explored in the Continental United States (CONUS) and then extended for global SM retrieval. The most challenging validation efforts show potential improvement for future spaceborne SM products with high spatial and temporal resolution. In addition, several SM fusion algorithms have been explored in order to combine several CYGNSS-based SM products. The fusion algorithm can help to achieve better estimation performance compared to individual products and keep the properties of individual products.

The achievable accuracy of hygrothermal building component simulation is significantly dependent on the applied material functions. These functions are determined by the material modelling marking the connection between the basic storage and transport parameters which are obtained from basic measurements, and the storage and transport coefficients which are defined within the balance and flow equations. It is the aim of the present study to develop a flexible and widely applicable material model which is not restricted to the current level of the transport theory. Furthermore, limits and options of this model are to be validated by means of four building materials on the basis of special transient moisture profile measurements. The study’s starting point is a comprehensive investigation of both, the different existing modelling approaches and the available experimental methods to determine basic hygrothermal material parameters. On this basis, the material modelling is set into the context of the heat and moisture transport theory derived from thermodynamics. The involved limits and restrictions are highlighted and options as well as requirements for further developments are pointed out. The developments this study focuses on comprise three fields: experiments for basic property determination, material modelling, and experiments for material model validation. The set of basic material investigation methods has been extended by the drying experiment under defined conditions. The different influences on the drying as well as its application to hygrothermal material model calibration are pointed out and appraised. On this basis, a drying apparatus is designed, built and applied. Ultimately, standardisation criteria and the derivation of a single-value drying coefficient are evaluated. Appropriate extensions are indicated. Based on the bundle of tubes approach, an own material model is developed. It is coupled with a mechanistical approach accounting for serial and parallel structured moisture transport phenomena. The derived liquid water conductivity is adjusted by the help of measured conductivity data close to saturation as well as within the hygroscopic moisture range. Subsequently, two internal modelling parameters are calibrated which is done by numerical simulation of the water uptake and the drying experiment under consideration of the hysteresis of moisture storage. Facilitating its application to the obtained laboratory data, the material model has been implemented into a computer program. It is applied to the four building materials brick, lime-sand brick, aerated concrete and calcium silicate. The adjusted material functions are shown and discussed. In all four cases, the calibration provides an excellent agreement between measured and calculated material behaviour. As experimental basis of the material model validation, the instantaneous profile measurement technique (IPM) has been extended to be applied in Building Physics. Special equipment is developed and measurement procedures are designed. Different models to derive the water content from dielectric data obtained by Time Domain Reflectometry (TDR) measurements are evaluated and implemented. Ultimately, an extensive program of transient moisture profile measurements within the hygroscopic and the overhygroscopic moisture content range is conducted and evaluated. Within the frame of validation, the developments on the experimental as well as on the modelling fields are combined. The IPM experiments are recalculated on the basis of the measured initial and boundary conditions applying the adjusted and calibrated material functions. The comparison of measured and calculated data reveals the power of the developed material modelling just as the consequences of the simplifications made on the transport theory level. The distinct influences of the hysteresis of moisture storage consisting of effects depending on the process history and effects depending on the process dynamics, are proven. By the presented study, the material modelling has been decisively further developed, the set of basic measurement methods has been extended by a substantial experiment and the instantaneous profile measurement technique has been made applicable to Building Physics. Moreover, the influences of the process history and the process dynamics on the moisture transport and the resulting moisture profiles could be shown and proven. By that, not only a material model is now available which perfectly applies to the requirements of flexibility, applicability and extendability. The obtained data provides also a powerful basis for further research and development. / Die Genauigkeit hygrothermischer Bauteilsimulation hängt maßgeblich von den verwendeten Materialfunktionen ab. Sie werden durch die Materialmodellierung bestimmt, welche die Verbindung zwischen den aus Basisexperimenten gewonnenen Speicher- und Transportparametern sowie den innerhalb der Bilanz- und Flussgleichungen definierten Speicher- und Transportkoeffizienten herstellt. Ziel der vorliegenden Arbeit ist zum einen die Entwicklung eines flexiblen, breit anwendbaren und gleichzeitig nicht auf den gegenwärtigen Stand der Transporttheorie beschränkten Materialmodells. Dessen Grenzen und Möglichkeiten sollen zum anderen auf der Grundlage spezieller instationärer Feuchteprofilmessungen anhand von vier Baustoffen untersucht und aufgezeigt werden. Ausgangspunkt der Arbeit ist eine ausführliche Beleuchtung sowohl der vorhandenen Modellansätze als auch der zur Verfügung stehenden experimentellen Methoden zur Bestimmung hygrothermischer Basisparameter. Auf dieser Grundlage wird die Materialmodellierung in den Kontext der aus der Thermodynamik abgeleiteten Wärmeund Feuchtetransporttheorie eingeordnet. Die damit verbundenen Grenzen und Einschränkungen werden hervorgehoben und Entwicklungsmöglichkeiten sowie weiterer Entwicklungsbedarf aufgezeigt. Dieser umfasst drei Bereiche: die Experimente zur Bestimmung von Basisparametern, die Materialmodellierung, sowie Experimente zur Modellvalidierung. Die Reihe der Basisexperimente wird um den Trocknungsversuch unter definierten Bedingungen erweitert. Die verschiedenen Einflüsse auf die Trocknung und deren Anwendung in der Kalibrierung hygrothermischer Materialmodellierung werden herausgestellt und bewertet. Darauf aufbauend wird eine Apparatur entworfen, gebaut und angewendet. Schließlich werden Kriterien zur Standardisierung und Ableitung eines Einzahlenkennwertes evaluiert. Sinnvolle Erweiterungen werden aufgezeigt. Es wird ein eigenes Materialmodell auf der Grundlage eines Porenbündelansatzes hergeleitet, welches mit einem mechanistischen Ansatz gekoppelt wird, der den Feuchtetransport in seriell und parallel strukturierte Bereiche untergliedert. Die abgeleitete Flüssigwasserleitfähigkeit wird anhand von Leitfähigkeitsmessdaten im nahe gesättigten sowie im hygroskopischen Feuchtebereich justiert. Zwei interne Modellparameter werden anschließend unter Berücksichtigung der Hysterese der Feuchtespeicherung anhand des Aufsaug- und des Trocknungsversuches kalibriert. Das Materialmodell ist zur Erleichterung der Anwendung in ein Computerprogramm zur Anpassung an die Labordaten implementiert worden. Das Programm wird auf die vier Baustoffe Ziegel, Kalksandstein, Porenbeton und Calciumsilikat angewendet. Die entsprechend angepassten Materialfunktionen werden gezeigt und diskutiert. Im Rahmen der Kalibrierung wird eine hervorragende Übereinstimmung zwischen gemessenem und berechnetem Materialverhalten erreicht. Zur Modellvalidierung wird die Augenblicksprofilmethode (IPM) für die bauphysikalische Anwendung erweitert. Spezielle Apparaturen werden entwickelt und Versuchsabläufe entworfen. Modelle zur Ableitung des Wassergehaltes aus mit Hilfe der Time Domain Reflectometry (TDR) gewonnenen Dielektrizitätsmessdaten werden evaluiert und implementiert. Schließlich wird ein umfangreiches Programm an Feuchteprofilmessungen im hygroskopischen und überhygroskopischen Feuchtebereich umgesetzt und ausgewertet. Im Rahmen der Validierung werden die Entwicklungen auf experimenteller sowie auf Modellierungsebene zusammengeführt. Die IPM Experimente werden anhand der gemessenen Anfangs- und Randbedingungen und auf der Grundlage der angepassten und kalibrierten Materialfunktionen nachgerechnet. Der Vergleich zwischen Messung und Rechnung offenbart die Stärke der entwickelten Materialmodellierung ebenso, wie den Einfluss der auf Ebene der Transporttheorie getroffenen Vereinfachungen. Ein deutlicher Einfluss der sich aus der Prozessgeschichte sowie der Prozessdynamik zusammensetzenden Hysterese der Feuchtespeicherung kann nachgewiesen werden. Mit der vorliegenden Arbeit ist somit nicht nur die Materialmodellierung entscheidend weiterentwickelt, die Reihe der einfachen Basisexperimente um einen wesentlichen Versuch erweitert und die Augenblicksprofilmethode für bauphysikalische Belange anwendbar gemacht worden, es wurden auch die Einflüsse der Prozessgeschichte, und erstmals auch der Prozessdynamik, auf den Feuchtetransport sowie die sich einstellenden Feuchteprofile deutlich aufgezeigt und nachgewiesen. Es ist demnach nicht nur ein Materialmodell, welches den gestellten Anforderungen an Flexibilität, breite Anwendbarkeit und Erweiterbarkeit genügt, entwickelt worden, es wird mit den gewonnenen Messdaten auch die Grundlage weiterer Forschung zur Verfügung gestellt.

The achievable accuracy of hygrothermal building component simulation is significantly dependent on the applied material functions. These functions are determined by the material modelling marking the connection between the basic storage and transport parameters which are obtained from basic measurements, and the storage and transport coefficients which are defined within the balance and flow equations. It is the aim of the present study to develop a flexible and widely applicable material model which is not restricted to the current level of the transport theory. Furthermore, limits and options of this model are to be validated by means of four building materials on the basis of special transient moisture profile measurements. The study’s starting point is a comprehensive investigation of both, the different existing modelling approaches and the available experimental methods to determine basic hygrothermal material parameters. On this basis, the material modelling is set into the context of the heat and moisture transport theory derived from thermodynamics. The involved limits and restrictions are highlighted and options as well as requirements for further developments are pointed out. The developments this study focuses on comprise three fields: experiments for basic property determination, material modelling, and experiments for material model validation. The set of basic material investigation methods has been extended by the drying experiment under defined conditions. The different influences on the drying as well as its application to hygrothermal material model calibration are pointed out and appraised. On this basis, a drying apparatus is designed, built and applied. Ultimately, standardisation criteria and the derivation of a single-value drying coefficient are evaluated. Appropriate extensions are indicated. Based on the bundle of tubes approach, an own material model is developed. It is coupled with a mechanistical approach accounting for serial and parallel structured moisture transport phenomena. The derived liquid water conductivity is adjusted by the help of measured conductivity data close to saturation as well as within the hygroscopic moisture range. Subsequently, two internal modelling parameters are calibrated which is done by numerical simulation of the water uptake and the drying experiment under consideration of the hysteresis of moisture storage. Facilitating its application to the obtained laboratory data, the material model has been implemented into a computer program. It is applied to the four building materials brick, lime-sand brick, aerated concrete and calcium silicate. The adjusted material functions are shown and discussed. In all four cases, the calibration provides an excellent agreement between measured and calculated material behaviour. As experimental basis of the material model validation, the instantaneous profile measurement technique (IPM) has been extended to be applied in Building Physics. Special equipment is developed and measurement procedures are designed. Different models to derive the water content from dielectric data obtained by Time Domain Reflectometry (TDR) measurements are evaluated and implemented. Ultimately, an extensive program of transient moisture profile measurements within the hygroscopic and the overhygroscopic moisture content range is conducted and evaluated. Within the frame of validation, the developments on the experimental as well as on the modelling fields are combined. The IPM experiments are recalculated on the basis of the measured initial and boundary conditions applying the adjusted and calibrated material functions. The comparison of measured and calculated data reveals the power of the developed material modelling just as the consequences of the simplifications made on the transport theory level. The distinct influences of the hysteresis of moisture storage consisting of effects depending on the process history and effects depending on the process dynamics, are proven. By the presented study, the material modelling has been decisively further developed, the set of basic measurement methods has been extended by a substantial experiment and the instantaneous profile measurement technique has been made applicable to Building Physics. Moreover, the influences of the process history and the process dynamics on the moisture transport and the resulting moisture profiles could be shown and proven. By that, not only a material model is now available which perfectly applies to the requirements of flexibility, applicability and extendability. The obtained data provides also a powerful basis for further research and development. / Die Genauigkeit hygrothermischer Bauteilsimulation hängt maßgeblich von den verwendeten Materialfunktionen ab. Sie werden durch die Materialmodellierung bestimmt, welche die Verbindung zwischen den aus Basisexperimenten gewonnenen Speicher- und Transportparametern sowie den innerhalb der Bilanz- und Flussgleichungen definierten Speicher- und Transportkoeffizienten herstellt. Ziel der vorliegenden Arbeit ist zum einen die Entwicklung eines flexiblen, breit anwendbaren und gleichzeitig nicht auf den gegenwärtigen Stand der Transporttheorie beschränkten Materialmodells. Dessen Grenzen und Möglichkeiten sollen zum anderen auf der Grundlage spezieller instationärer Feuchteprofilmessungen anhand von vier Baustoffen untersucht und aufgezeigt werden. Ausgangspunkt der Arbeit ist eine ausführliche Beleuchtung sowohl der vorhandenen Modellansätze als auch der zur Verfügung stehenden experimentellen Methoden zur Bestimmung hygrothermischer Basisparameter. Auf dieser Grundlage wird die Materialmodellierung in den Kontext der aus der Thermodynamik abgeleiteten Wärmeund Feuchtetransporttheorie eingeordnet. Die damit verbundenen Grenzen und Einschränkungen werden hervorgehoben und Entwicklungsmöglichkeiten sowie weiterer Entwicklungsbedarf aufgezeigt. Dieser umfasst drei Bereiche: die Experimente zur Bestimmung von Basisparametern, die Materialmodellierung, sowie Experimente zur Modellvalidierung. Die Reihe der Basisexperimente wird um den Trocknungsversuch unter definierten Bedingungen erweitert. Die verschiedenen Einflüsse auf die Trocknung und deren Anwendung in der Kalibrierung hygrothermischer Materialmodellierung werden herausgestellt und bewertet. Darauf aufbauend wird eine Apparatur entworfen, gebaut und angewendet. Schließlich werden Kriterien zur Standardisierung und Ableitung eines Einzahlenkennwertes evaluiert. Sinnvolle Erweiterungen werden aufgezeigt. Es wird ein eigenes Materialmodell auf der Grundlage eines Porenbündelansatzes hergeleitet, welches mit einem mechanistischen Ansatz gekoppelt wird, der den Feuchtetransport in seriell und parallel strukturierte Bereiche untergliedert. Die abgeleitete Flüssigwasserleitfähigkeit wird anhand von Leitfähigkeitsmessdaten im nahe gesättigten sowie im hygroskopischen Feuchtebereich justiert. Zwei interne Modellparameter werden anschließend unter Berücksichtigung der Hysterese der Feuchtespeicherung anhand des Aufsaug- und des Trocknungsversuches kalibriert. Das Materialmodell ist zur Erleichterung der Anwendung in ein Computerprogramm zur Anpassung an die Labordaten implementiert worden. Das Programm wird auf die vier Baustoffe Ziegel, Kalksandstein, Porenbeton und Calciumsilikat angewendet. Die entsprechend angepassten Materialfunktionen werden gezeigt und diskutiert. Im Rahmen der Kalibrierung wird eine hervorragende Übereinstimmung zwischen gemessenem und berechnetem Materialverhalten erreicht. Zur Modellvalidierung wird die Augenblicksprofilmethode (IPM) für die bauphysikalische Anwendung erweitert. Spezielle Apparaturen werden entwickelt und Versuchsabläufe entworfen. Modelle zur Ableitung des Wassergehaltes aus mit Hilfe der Time Domain Reflectometry (TDR) gewonnenen Dielektrizitätsmessdaten werden evaluiert und implementiert. Schließlich wird ein umfangreiches Programm an Feuchteprofilmessungen im hygroskopischen und überhygroskopischen Feuchtebereich umgesetzt und ausgewertet. Im Rahmen der Validierung werden die Entwicklungen auf experimenteller sowie auf Modellierungsebene zusammengeführt. Die IPM Experimente werden anhand der gemessenen Anfangs- und Randbedingungen und auf der Grundlage der angepassten und kalibrierten Materialfunktionen nachgerechnet. Der Vergleich zwischen Messung und Rechnung offenbart die Stärke der entwickelten Materialmodellierung ebenso, wie den Einfluss der auf Ebene der Transporttheorie getroffenen Vereinfachungen. Ein deutlicher Einfluss der sich aus der Prozessgeschichte sowie der Prozessdynamik zusammensetzenden Hysterese der Feuchtespeicherung kann nachgewiesen werden. Mit der vorliegenden Arbeit ist somit nicht nur die Materialmodellierung entscheidend weiterentwickelt, die Reihe der einfachen Basisexperimente um einen wesentlichen Versuch erweitert und die Augenblicksprofilmethode für bauphysikalische Belange anwendbar gemacht worden, es wurden auch die Einflüsse der Prozessgeschichte, und erstmals auch der Prozessdynamik, auf den Feuchtetransport sowie die sich einstellenden Feuchteprofile deutlich aufgezeigt und nachgewiesen. Es ist demnach nicht nur ein Materialmodell, welches den gestellten Anforderungen an Flexibilität, breite Anwendbarkeit und Erweiterbarkeit genügt, entwickelt worden, es wird mit den gewonnenen Messdaten auch die Grundlage weiterer Forschung zur Verfügung gestellt.

Ces travaux de thèse portent sur la détection de défauts non francs dans des structures filaires particulières : les lignes de transmission a multiconducteurs (MTL), aussi appelées torons de câbles. Couramment employées pour le diagnostic de réseaux filaires, les méthodes par réflectométrie ne sont, pour l'heure, pas suffisamment performantes pour détecter de tels défauts. Par ailleurs, elles n'ont, en général, été étudiées et développées que pour des lignes simples, ou les phénomènes de couplages électromagnétiques entre les conducteurs (diaphonie) ne sont pas présents. Ces derniers sont cependant porteurs d'information supplémentaire sur l'état du câble. Les utiliser permettrait d'accroître la sensibilité de détection aux défauts. L'objectif est de proposer une nouvelle méthode de réflectométrie, tirant profit des signaux de diaphonie pour détecter les défauts non francs. Une telle méthode présente également l'avantage d'être adaptée aux structures en toron. Après avoir étudié l'impact d'un défaut non franc sur les paramètres caractéristiques d'une MTL et sur les signaux de diaphonie, une méthode, la "Cluster Time Frequency Domain Reflectometry ", a pu être proposée. Il s'agit d'un procédé en trois étapes. Des mesures par réflectométrie temporelle sont tout d'abord réalisées à l'entrée de la ligne à diagnostiquer. Tous les signaux présents, y compris ceux de diaphonie, sont enregistrés. Un traitement temps-fréquence leur est ensuite appliqué afin d'amplifier la présence d'éventuels défauts. Enfin, un algorithme de clustering, spécifiquement développé pour le diagnostic filaire, est utilisé de manière a bénéficier de l'ensemble de l'information disponible / Research works presented in this thesis rely on detecting soft faults (incipient faults) in specic wiring structures : multiconductor transmission lines (MTL), also known as bundles of wires. Reflectometry methods, often used for the diagnosis of wiring networks, aren't for now efficient enough at detecting such defects. Besides, they have been designed for single lines only, where electromagnetic coupling between conductors (crosstalk) is not to be considered. However such phenomenon can provide more information about the state of the cable. Using this information could enable us to detect soft faults more easily. Our goal is to propose a new reflectometry method, which takes advantage of crosstalk signals in order to detect incipient faults. Such a tool has also the advantage of being well-adapted to bundles of cables. Thanks to the preliminary study of the impact of soft faults on the characteristic parameters of a MTL and on crosstalk signals, a method called "Cluster Time Frequency Domain Reflectometry ", has been proposed. It is a three step process. Firts temporal reflectometry measurements are made at the beginning of the line under test. All the available signals, even crosstalk ones, are recorded. A time-frequency process is then applied on them, in order to amplify the presence of defects. Finally, a clustering algorithm, that has been specically developed for wiring diagnosis, is used to benefit from the whole available information

This thesis details the application of a medium frequency (MF) Doppler radar to observations of meteoroids entering the Earth's atmosphere. MF radars make possible a greater height coverage of the meteor region (70 to 160 km) than conventional meteor radars. However this type of radar has generally been under-utilised for meteor observations, primarily due to the less than ideal radio environment associated with MF systems. This situation demanded selection of the most appropriate radar meteor techniques and in this respect a variety of techniques are evaluated for application at this frequency. The 2 MHz radar system used in this study is located at the Buckland Park research facility (35.6 deg. S, 138.5 deg. E), near Adelaide, South Australia and is operated by the Department of Physics of the University of Adelaide. This radar has the largest antenna of any MF radar with 89 crossed dipoles distributed over an area of about 1 km in diameter. Beam forming is achieved by varying the phase to groups of elements of the array. The array was constructed in the 1960's, and while having several upgrades, a preliminary examination of the array and associated systems indicated that a significant amount of maintenance work would be required to enable the system to be used for meteor observations. It was also apparent that the software used with the radar hardware for atmospheric studies was not suitable for processing meteor data. Thus a major refurbishment of the radar hardware, as well as the development of appropriate software, was initiated. The complete radar system was divided into its constituent components of antenna array, transmitter, receiver and computer systems. The transmitter and receiver systems were examined and various improvements made including increasing total output power and enhancing beam steering capability. Time domain reflectometry (TDR) techniques were extensively used on the antenna array, as many feed cables showed the presence of moisture. New hardware in the form of a portable power combining system was designed, constructed and tested to further increase radar experimental capabilities. Techniques were developed that verified system performance was to specification. Extensive night time observations of sporadic and shower meteor events were made over a two and a half year period. A particular study was made of the Orionids shower as well as other meteor activity on the night of 22 October 2000. Using the upgraded beam swinging features of the array, a narrow radar beam was used to track the shower radiant in an orthogonal sense so as to maximise the number of shower meteors detected. From each echo, various intrinsic meteoroid parameters were determined, including meteor reflection point angle-of-arrival using a five-element interferometer, echo duration and height; meteoroid speeds were determined using the Fresnel phase time technique. Meteor echoes belonging to the Orionids radiant were selected using a coordinate transform technique. The speed was then used as an additional discriminant to confirm the Orionid shower members. A second radiant, observed at a slightly higher declination is classified as also part of the Orionid stream. The sporadic meteor component in the data set was examined and found to exhibit speeds much higher than expected for sporadic meteors at the time of the observations. However, these results are consistent with a selection bias based on meteoroid speed, that is inherent in radar observations. The Orionid observations indicate that the refurbishment of the radar system and the introduction of new software for meteor analysis has been successfully achieved and that radar meteor studies can now be carried out routinely with the Buckland Park 2 MHz radar. Moreover it has been shown for the first time that meteoroid speeds can be determined with a MF radar operating on a PRF as low as 60 Hz. / Thesis (Ph.D.)--School of Chemistry and Physics, 2003.