Polystyrene behaviour in reversed phase high performance liquid chromatography was influenced mainly by the solvent system, but secondary affects were observed depending on the stationary phase. A variety of reversed phase columns were investigated using mobile phase combinations of dichlorom ethane-methanol, dichloromethane-acetonitrile, ethyl acetate-methanol and ethyl acetate-acetonitrile. Several different modes of behaviour were observed depending on the polymer solubility in the solvent system. In the dichloromethane-methanol solvent system, polymer-stationary phase interactions only occurred when the molecules had pore access. Retention of excluded polystyrene depended on the kinetics of precipitation and redissolution of the polymer. Peak splitting and band broadening occurred when the kinetics were slow and molecular weight separations were limited !o oligomers and polystyrenes lower than 5-10(4) dalton. Excellent molecular weight separations of polystyrenes were obtained using gradient elution reversed phase chromatography with a dichloromethane-acetonitrile mobile phase on C18 columns. The retention was based on polymer-stationary phase interactions regardless of the column pore size. Separations were obtained on large diameter pellicular adsorbents that were almost as good as those obtained on porous adsorbents, showing that pore access was not essential for the retention of high molecular weight polystyrenes. In the best example, the separation ranged from the monomer to 10(6) dalton in a single analysis. Very little adsorption of excluded polymers was observed on C8 or phenyl columns. Polystyrene molecular weight separations to 7-10(5) dalton were obtained in an ethyl acetate-acetonitrile solvent system on C18 columns. Adsorption was responsible for retention. When an ethyl acetate-methanol solvent system was used, no molecular weight separations were obtained because of complex peak splitting. Reversed phase chromatography was compared to size exclusion chromatography for the analysis of polydisperse polystyrenes. Similar results were obtained using both methods. However, the reversed phase method was less sensitive to concentration effects and gave better resolution.

The thesis consists of two parts targeting the characterization of chromatographic behavior of linear tryptic and cyclic peptides containing oxidized methionine (Met) in reversed-phased chromatography. The retention order of methionine-containing peptide analogues was observed to be the same in both studies: Met oxide < Met dioxide < Met. For linear tryptic peptides, the magnitude of the retention time shift may vary dramatically: from –9 % to +0.36 % acetonitrile. Particularly, large negative retention time shifts are found mostly associated with methionine being in the hydrophobic face of an amphipathic helix. Contrary to previously reported observations, I demonstrate for the first time that methionine oxidation may increase peptide hydrophobicity, this occurs only when methionine is in the N3 position of the N-capping stabilization motif preceding an amphipathic helix. In the second study, the effect of peak splitting was observed for some Met oxide-containing cyclolinopeptides, which most likely appear due to diastereomerization.

The thesis is focused on application of ion chromatography in pharmaceutical analyses of organic ions. Ion chromatography is increasingly used in the field of pharmaceutical analysis. This includes the analysis of impurities and metabolites. In the first part of this thesis, ion chromatography is compared with common separation techniques used in pharmacy, such as gas chromatography and high performance liquid chromatography. In the second part development and validation of methods of ion chromatography for purity evaluation and quality control of active pharmaceutical substances Rivastigmine hemitartrate and Pramipexole hydrochloride were carried out. Key words: ion chromatography, reversed-phase chromatography, ion-pair chromatography, ion-exclusion chromatography, ion-exchange chromatography, GC, HPLC

No description available.

<p>LC-MS of protein drugs requires new ideas in bonded phase design rather than adapting bonded phases from the realm of small-molecule drugs. The polymer-shell bonded phase is designed to interact with larger molecules and to shield proteins from the silica substrate. The particles consist of a core of solid silica and a shell of dense polymer brush. The polymer layer is thick enough to protect the protein from interactions with silanols to reduce peak tailing. The polymer contains multiple functional groups that introduce more selectivity. This design gives unprecedented LC resolution and MS sensitivity. Our group has developed polymer shell bonded phases for hydrophobic interaction chromatography (HIC-MS) of antibody-drug conjugates (ADCs), hydrophilic interaction liquid chromatography (HILIC-MS) of glycoproteins, and reversed-phase liquid chromatography (RPLC-MS) of monoclonal antibodies. Since HIC is not in-line compatible with MS due to the high salt levels, it is laborious to identify the constituents of HIC peaks. An MS-compatible alternative to HIC is reported here: native reversed phase liquid chromatography (nRPLC). This employs a mobile phase 50 mM ammonium acetate for high sensitivity in MS, and elution with a gradient of water/isopropanol. The nRPLC-MS data show that all ADC species, ranging from drug-to-antibody ratios of 1 to 8, remained intact and native on the column. As we adapt this concept to intact proteins, we find that lysozyme and α-chymotrypsinogen A are both eluted in their native conformations. We also use the polymer-shell concept to resolve IgG1 free thiol variants by RPLC-MS with 0.5% formic acid. Since there are always other variants besides the intended ones, the need for high MS sensitivity is desired to distinguish subtle mass change between disulfide bond and free thiols. Overall, MS sensitivity increases 10X relative while all of the thiol variants are well resolved by the polymethylmethacrylate bonded phase.</p>

<p>Liquid chromatography coupling with mass spectrometry (LC/MS) plays an important role in pharmaceutical characterization because of its ability to separate, identify, and quantify individual compounds from the mixture. Polymer brush layer bonded to the silica surface is designed as a novel stationary phase to improve the LC resolution and MS compatibility. The polymer thickness can be controlled to shield the analyte from interacting with the active silanol on the surface and reduce peak tailing. The functional group of the polymer can be changed to tune the selectivity in different separation modes. </p><p> </p><p>Two projects on LC/MS method development for biomolecule characterization using polymer-shell column are discussed in this work. In the first project, a polymer-shell column is used for disulfide bonds and free thiol subspecies identification, which is a major type of structural heterogeneities in IgG1. Compared with commercial columns, the polymer-shell column is able to resolve the free thiol variants without the presence of trifluoroacetic acid and greatly improve the MS signal. In the second project, a polymer-shell column is used for characterizing the drug-loading profile for antibody-drug-conjugates (ADC) via online LC/MS. The separation employs a mobile phase of 50 mM ammonium acetate to keep the ADC intact, and a gradient of water/isopropanol for ADC elution. MS data show that all ADC species remained intact and native on the column. Positional isomers can be separated and identified with the new method as well. Furthermore, to understand the surface chemistry and protein separation behavior quantitatively, a chromatographic simulation study is performed. The result shows that protein separation in RPLC can be described by a bi-Langmuir adsorption isotherm with mixed-mode retention of strong and weak sites. Smaller fractions and lower equilibrium constant of the strong site, which is the active silanol, give less tailing for protein separation.</p>

My work has focused on a variety of different types of diamond-based, core-shell particles. These particles are formed with inert cores and poly(allylamine)/nanodiamond shells. Their intended purpose is to form an LC stationary phase that is stable from pH 1 – 14 and at elevated temperatures. At the beginning of my studies, the particles that had been made in the Linford laboratory were pH stable, but irregular and had poor mechanical stability. Since that time, I have worked to improve the particles by using more spherical zirconia and carbon cores, and I have improved their mechanical stability via chemical crosslinking with epoxides. I have performed van Deemter and van’t Hoff analyses to understand the properties of these columns. Efficiencies greater than 100,000 N/m are routinely achieved with these carbon/nanodiamond-based phases. In addition I contributed to two patents that show innovations in diamond functionalization. My contributions involved reduction of an oxidized diamond surface with LiAlH4 prior to functionalization with isocyanates. I also wrote some application notes for the Flare mixed-mode column, which was recently introduced to the market and contains particles comprised of a carbon core and a polymer/nanodiamond shell. These application notes show the gradient separations of four essential oils (lavender, melaleuca, peppermint and eucalyptus), and the isocratic separations of various triazine herbicides and a mixture of β2-agonists and amphetamines.This dissertation contains the following sections. Chapter 1 is a review of liquid chromatographic history and theory. It also includes a history of the use of diamonds in liquid chromatography. Chapter 2 is a study on a glassy carbon core - polymer/nanodiamond shell particle made in our laboratory. Stability studies at pH 11.3 and 13 were performed and different analytes were retained and/or separated on the column. Chapter 3 is a study performed on the Flare mixed-mode column. Separations of tricyclic antidepressants, β2-andrenergic receptor agonists, and linear chain alkylbenzenes were demonstrated with this phase. Van Deemter and van’t Hoff studies were also performed to probe the efficiency and selectivity of this column with different classes of analytes. Chapter 4 chronicles, via SEM and van Deemter analysis, the improvements that have taken place in our column after many iterations of improved synthetic methods and new materials. These include better particle uniformity, particle stability, and column efficiency. Three different carbon cores were analyzed, each better than the previous one. Appendices 1 – 6 are application notes published by Diamond Analytics of β2-andrenergic receptor agonists and amphetamines, triazine herbicides, and lavender, melaleuca, eucalyptus and peppermint essential oils. Appendices 7 and 8 are patents that contain ideas and research contributed by the author.

Foram desenvolvidas metodologias de cromatografia a líquido de fase reversa baseadas em injeção sequencial (SIC) e em cromatografia a líquido de alta eficiência (HPLC) para determinação de triclosan em amostras de produtos de higiene pessoal e em estudos de adsorção em argilominerais naturais e modificados, visando determinar parâmetros de adsorção de triclosan frente a alguns de seus metabólitos. A determinação de triclosan em enxaguadores bucais foi realizada por SIC com eluição isocrática usando fase móvel constituída por acetonitrila: tampão fosfato de trietilamina 70 mM pH 3,5 na proporção 70:30 (v v-1), obtendo-se limites de detecção e de quantificação de 0,22 e 0,72 mg L-1, respectivamente. Taxas de recuperação entre 96 e 98% foram obtidas da aplicação a amostras reais, sendo que os resultados obtidos pelo método proposto não apresentaram evidências de diferenças estatisticamente significativas em comparação a uma metodologia de referência baseada em HPLC com coluna empacotada. A separação de triclosan (TCS), 2-clorofenol (2-CP), 2,4-diclorofenol (2,4-DCP), 2,4,6-triclorofenol (2,4,6-TCP), 2,3,4-triclorofenol (2,3,4-TCP) e metiltriclosan (MTCS) foi estudada por SIC, obtendo-se a separação de TCS, 2-CP, 2,4-DCP e 2,4,6-TCP com duas etapas de eluição isocrática, a primeira delas com fase móvel 60:40 (v v-1) metanol: tampão acetato de amônio 20 mM (pH 5,5) seguida de eluição com fase móvel 70:30 (v v-1) metanol : tampão acetato de amônio 20 mM (pH 5,5). Nesse caso, os isômeros 2,4,6-TCP e 2,3,4-TCP coeluem. Metiltriclosan, o menos polar desses compostos, pode ser separado de TCS com etapas subseqüentes de eluição. Os métodos foram aplicados para estudar a adsorção de triclosan e seus metabólitos 2,4-DCP, 2,4,6-TCP e metiltriclosan em montmorilonita homoiônica (K+) e modificada com sal de hexadeciltrimetilamônio (HDTMA), observando-se forte adsorção de triclosan e metiltriclosan em comparação a 2-CP, 2,4-DCP e 2,4,6-TCP. A incorporação de HDTMA no argilomineral causou significativo aumento da capacidade de adsorção desses metabólitos, determinada a partir do ajuste dos dados experimentais à equação linearizada de Langmuir, observando-se que a ordem de adsorção é 2,4,6-TCP > 2,4-DCP > 2-CP / Reversed-phase liquid chromatography methodologies based on sequential injection (SIC) and high performance liquid chromatography (HPLC) have been developed for determination of triclosan in samples of personal hygiene products and in studies of adsorption on natural and modified clay minerals aiming to determine kinetic and thermodynamic parameters of adsorption of triclosan in comparison with some of its metabolites. The determination of triclosan in oral rinses with SIC was performed by isocratic elution using a mobile phase of acetonitrile : 70 mM triethylamine phosphate buffer pH 3.5 at the ratio 70:30 (v v-1), obtaining limits of detection and quantification of 0.22 and 0.72 mg L-1, respectively. Recovery rates between 96 and 98 % were obtained from the application to commercial samples, and the results obtained by the proposed method showed no evidence of statistically significant differences compared to the reference methodology based on HPLC with packed column. The separation of triclosan (TCS), 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TCP), 2,3,4 trichlorophenol (2,3,4-TCP) and methyltriclosan (MTCS) was studied by SIC, resulting in the separation of TCS, 2-CP, 2,4-DCP and 2,4,6-TCP with two isocratic elution steps, the first of them with a mobile phase 60:40 (v v-1) methanol: 20 mM ammonium acetate buffer (pH 5.5) followed by elution with 70:30 (v v-1) mobile phase of methanol : 20 mM ammonium acetate buffer (pH 5.5). In this case, the isomers 2,4,6-TCP and 2,3,4-TCP coeluted. Methyltriclosan, the less polar of these compounds, can be separated from TCS with subsequent elution steps. The methods were applied to study the adsorption of triclosan and its metabolites 2-CP, 2,4-DCP, 2,4,6-TCP and methyltriclosan on homoionic montmorillonite (K+) as well as in hexadecyltrimethylammonium salt (HDTMA) modified montmorillonite, noticing a stronger adsorption of triclosan and methyltriclosan compared with 2-CP, 2,4-DCP and 2,4,6-TCP. Incorporation of HDTMA in the clay mineral caused significant increase in adsorption capacity of these metabolites. This capacity was determined by fitting the experimental data to the linearized Langmuir equation. The adsorption order was 2,4,6-TCP > 2,4-DCP > 2-CP.

Foram desenvolvidas metodologias de cromatografia a líquido de fase reversa baseadas em injeção sequencial (SIC) e em cromatografia a líquido de alta eficiência (HPLC) para determinação de triclosan em amostras de produtos de higiene pessoal e em estudos de adsorção em argilominerais naturais e modificados, visando determinar parâmetros de adsorção de triclosan frente a alguns de seus metabólitos. A determinação de triclosan em enxaguadores bucais foi realizada por SIC com eluição isocrática usando fase móvel constituída por acetonitrila: tampão fosfato de trietilamina 70 mM pH 3,5 na proporção 70:30 (v v-1), obtendo-se limites de detecção e de quantificação de 0,22 e 0,72 mg L-1, respectivamente. Taxas de recuperação entre 96 e 98% foram obtidas da aplicação a amostras reais, sendo que os resultados obtidos pelo método proposto não apresentaram evidências de diferenças estatisticamente significativas em comparação a uma metodologia de referência baseada em HPLC com coluna empacotada. A separação de triclosan (TCS), 2-clorofenol (2-CP), 2,4-diclorofenol (2,4-DCP), 2,4,6-triclorofenol (2,4,6-TCP), 2,3,4-triclorofenol (2,3,4-TCP) e metiltriclosan (MTCS) foi estudada por SIC, obtendo-se a separação de TCS, 2-CP, 2,4-DCP e 2,4,6-TCP com duas etapas de eluição isocrática, a primeira delas com fase móvel 60:40 (v v-1) metanol: tampão acetato de amônio 20 mM (pH 5,5) seguida de eluição com fase móvel 70:30 (v v-1) metanol : tampão acetato de amônio 20 mM (pH 5,5). Nesse caso, os isômeros 2,4,6-TCP e 2,3,4-TCP coeluem. Metiltriclosan, o menos polar desses compostos, pode ser separado de TCS com etapas subseqüentes de eluição. Os métodos foram aplicados para estudar a adsorção de triclosan e seus metabólitos 2,4-DCP, 2,4,6-TCP e metiltriclosan em montmorilonita homoiônica (K+) e modificada com sal de hexadeciltrimetilamônio (HDTMA), observando-se forte adsorção de triclosan e metiltriclosan em comparação a 2-CP, 2,4-DCP e 2,4,6-TCP. A incorporação de HDTMA no argilomineral causou significativo aumento da capacidade de adsorção desses metabólitos, determinada a partir do ajuste dos dados experimentais à equação linearizada de Langmuir, observando-se que a ordem de adsorção é 2,4,6-TCP > 2,4-DCP > 2-CP / Reversed-phase liquid chromatography methodologies based on sequential injection (SIC) and high performance liquid chromatography (HPLC) have been developed for determination of triclosan in samples of personal hygiene products and in studies of adsorption on natural and modified clay minerals aiming to determine kinetic and thermodynamic parameters of adsorption of triclosan in comparison with some of its metabolites. The determination of triclosan in oral rinses with SIC was performed by isocratic elution using a mobile phase of acetonitrile : 70 mM triethylamine phosphate buffer pH 3.5 at the ratio 70:30 (v v-1), obtaining limits of detection and quantification of 0.22 and 0.72 mg L-1, respectively. Recovery rates between 96 and 98 % were obtained from the application to commercial samples, and the results obtained by the proposed method showed no evidence of statistically significant differences compared to the reference methodology based on HPLC with packed column. The separation of triclosan (TCS), 2-chlorophenol (2-CP), 2,4-dichlorophenol (2,4-DCP), 2,4,6-trichlorophenol (2,4,6-TCP), 2,3,4 trichlorophenol (2,3,4-TCP) and methyltriclosan (MTCS) was studied by SIC, resulting in the separation of TCS, 2-CP, 2,4-DCP and 2,4,6-TCP with two isocratic elution steps, the first of them with a mobile phase 60:40 (v v-1) methanol: 20 mM ammonium acetate buffer (pH 5.5) followed by elution with 70:30 (v v-1) mobile phase of methanol : 20 mM ammonium acetate buffer (pH 5.5). In this case, the isomers 2,4,6-TCP and 2,3,4-TCP coeluted. Methyltriclosan, the less polar of these compounds, can be separated from TCS with subsequent elution steps. The methods were applied to study the adsorption of triclosan and its metabolites 2-CP, 2,4-DCP, 2,4,6-TCP and methyltriclosan on homoionic montmorillonite (K+) as well as in hexadecyltrimethylammonium salt (HDTMA) modified montmorillonite, noticing a stronger adsorption of triclosan and methyltriclosan compared with 2-CP, 2,4-DCP and 2,4,6-TCP. Incorporation of HDTMA in the clay mineral caused significant increase in adsorption capacity of these metabolites. This capacity was determined by fitting the experimental data to the linearized Langmuir equation. The adsorption order was 2,4,6-TCP > 2,4-DCP > 2-CP.

(EN) In the first part of this work, analytical methods for determination of impurities of active pharmaceutical ingredients (API) in combined pharmaceutical dosage forms were developed and validated. Development of the methods covered both the optimization of sample preparation procedure and chromatographic conditions. The methods were validated according to International Conference on Harmonization guideline and both of them were confirmed to be able to analyze stability samples. Impurities in paracetamol, codeine phosphate hemihydrate and pitophenone hydrochloride in the presence of fourth API fenpiverinium bromide were separated by using ion-pair reversed phase chromatography with gradient elution. Symmetry C18, 250 x 4,6 mm, 5 µm heated to 35 řC was used as a separation column. A diode array detector was used. The detection wavelengths were set as follows: 220 nm for paracetamol impurity K, 245 nm for paracetamol and its other impurities and 285 nm for codeine, pitophenone and their impurities. Impurities in valsartan, amlodipine besylate and hydrochlorothiazide were separated by reversed phase UHPLC method with gradient elution. Chromatographic column Zorbax Eclipse C8 RRHD, 100 x 3,0 mm, 1,8 µm heated to 30 řC and spectrophotometric detection were used. The detection wavelengths were set as...