No description available.

Understanding the behavior of geomaterials under explosive loading is essential for several applications in the mining and oil industry. To date, the design of these applications is based almost solely on empirical equations and tabulated data. Optimal designs require accurate and complete knowledge of rock behavior under various loading conditions. The vast majority of the properties available in the literature have been gathered by deforming the specimen slowly. These properties have been used to establish constitutive models which describe the behavior of rocks under static and quasi-static loading conditions. However, the dynamic properties and material constitutive models describing the behavior of geomaterials under high strain-rate loading conditions are essential for a better understanding and enhanced designs of dynamic applications. Some attempts have been made to measure dynamic properties of rocks. Also, some trials have been made to devise material models which describe the behavior of rocks and the evolution of damage in the rock under dynamic loading. Published models were successful in predicting tensile damage and spalling in rocks. However, there are no established models capable of predicting compressional damage in rocks due to dynamic loading. A recently-developed model, the RHT model, was formulated to describe the behavior of concrete over the static and dynamic ranges. The model was also formulated to predict compressional damage based on the strain rate at which the material is subjected to. The RHT model has been used successfully in several applications. The purpose of this research was to characterize one rock type as an example of a hard brittle rock. The physical properties of the rock as well as the static and dynamic mechanical properties were investigated. These properties were used to calibrate the RHT model and investigate its potentials to predict compressional damage in brittle materials. The calibrated model showed good precision reproducing the amplitude of the strain signals generated by explosive loading. It was also capable of predicting compressional damage with acceptable accuracy. Unfortunately, due to implementation restrictions, tensile and spall damage could not be captured by the model. The duration and shape of the strain pulse were also poorly modeled. / Thesis (Ph.D, Mining Engineering) -- Queen's University, 2010-12-22 17:54:05.887

Porous solids are a class of materials of high scientific and technological significance. Indeed, they have the ability to interact with atoms, ions or molecules not only at their surface but also throughout the bulk of the solid. This ability places these materials as a major class involved in many applications such as gas storage and separation, catalysis, drug delivery and sensor technology. Metal-Organic Materials (MOMs) or coordination polymers (CPs) are crystalline compounds constructed from metal ions or clusters and organic components that are linked via coordination bonds to form zero-, one-, two or three-periodic structures. Porous Metal-Organic Materials (MOMs) or Metal-Organic Frameworks (MOFs) are a relatively new class of nanoporous materials that typically possess regular micropores stable upon removal of guests. An extraordinary academic and industrial interests was witnessed over the past two decades and is evidenced by a fantastic grow of these new materials. Indeed, due to a self-assembly process and readily available metals and organic linkers, an almost infinite number of materials can, in principle, be synthesized. However, a rational design is very challenging but not impossible. In theory, MOMs could be designed and synthesized with tuned functionalities toward specific properties that will determine their potential applications. The present research involves the design and synthesis of functional porous Metal-Organic Materials that can be used as platforms for specific studies related to many applications such as for example gas storage and particularly hydrogen storage. In this manuscript, I will discuss the studies performed on existing major Metal-Organic Frameworks, namely Zeolite-like Metal-Organic Frameworks (ZMOFs) that were designed and synthesized in my research group. My research was also focused on the design and the synthesis of new highly porous isoreticular materials based on Metal-Organic Polyhedra (MOP) where desirable functionality and unique features can be introduced in the final material prior and/or after the assembly process. The use of hetero-functional ligands for a rational design toward binary or ternary net will also be discussed in this dissertation.

Thermal resistance per unit thickness for Vacuum Insulation Panel (VIP) is 5 to 10 times higher than conventional insulation materials. This makes VIP an attractive option for retrofitting exterior building envelopes. Insulation can be added in an exterior wall either on the interior side, exterior side or in the available stud cavity. VIP has high vapor diffusion resistance factor and could lead to moisture management risk in the wall layers because of the steep temperature gradient in the wall generated due to very high thermal resistance of VIP. VIP is a relatively new insulation material for building envelope construction, thus the hygrothermal or moisture management performance of VIP-insulated exterior building envelopes need to be critically analyzed before its application. This study aims to evaluate the moisture management risk associated with wood-frame stucco-cladded exterior walls retrofitted with VIP using a 2-D hygrothermal simulation tool WUFI-2D. Eight North American locations were considered, based on Moisture Index (MI) which varied between 0.13 and 1.17, and two different indoor hygrothermal loading conditions as prescribed by the ASHRAE 160P and EN 13788, respectively. The outputs from hygrothermal simulations (water content, relative humidity and temperature) were critically analysed and expressed further using freeze-thaw cycles and RHT indices. The results show that the appropriately designed VIP retrofitted walls can have superior moisture management performance as compared to conventional stucco-cladded wall. / Graduate

ABSTRACT Triticum sphaerococcum (AABBDD, 2n = 6x = 42) is a land race of wheat known from the Indian subcontinent. It has several favourable characters including short and strong culms, hemispherical grains with a shallow crease (that may increase the yield of white flour), higher protein content compared to bread wheat (T. aestivum), and resistance to drought, and yellow rust caused by Puccinia striiformis. However, an unfavourable characteristic of T. sphaerococcum is its lower yield compared to bread wheat. Being a land race, the sphaerococcum wheat is poorly studied. This study was undertaken to increase knowledge of the physiology and genetics of this land race and determine if it may be possible to separate the favourable characters of T. sphaerococcum from its unfavourable characters. Plant height in bread wheat is controlled by many genes. ‘Reduced Height’ (Rht) genes which differ in their response to externally applied gibberellic acid (GA3) are responsible for the short stature of modern bread wheat varieties. Therefore, GA3 was used to probe the relationship between the semidwarf sphaerococcum phenotype and the Rht gene. T. sphaerococcum variety Sp5 showed a unique “seedling response” to externally applied GA3 when compared with T. aestivum varieties harbouring Rht1, Rht2, Rht8, Rht12, Rht13 or Rht18 alleles. A mapping population of doubled haploids was generated through wide hybridisation of F1 (Sp5 x Otane) with Zea mays. A genome-wide scan of Sp5 and Otane (parents) using 348 microsatellite (SSR) markers showed that only 169 of these markers (49%) were polymorphic between the parents. A DArT profiling yielded 348 markers that were polymorphic between the parents. Microsatellite markers and DArT markers were used to create a genetic map. The mapping population was phenotyped and a quantitative trait loci (QTL) analysis was performed for component traits of the complex sphaerococcum trait including plant height, spike length, awn length, yield, grain shape and crease size. Results of the QTL analysis indicated that it may be difficult to separate the favourable characters of T. sphaerococcum from its unfavourable characters through mutation because the component traits of the complex sphaerococcum trait may be under pleiotropic control of the Sp gene. The hypothesis that T. sphaerococcum originated through a mutation in T. aestivum was tested through induced mutation using gamma rays. Mutants from sphaerococcum-type to aestivum-type were isolated and phenotyped. Sphaerococcum-type mutants also were isolated and characterised from mutated aestivum-type wheat suggesting a possible origin of T. sphaerococcum through a mutation in T. aestivum.

ABSTRACT Triticum sphaerococcum (AABBDD, 2n = 6x = 42) is a land race of wheat known from the Indian subcontinent. It has several favourable characters including short and strong culms, hemispherical grains with a shallow crease (that may increase the yield of white flour), higher protein content compared to bread wheat (T. aestivum), and resistance to drought, and yellow rust caused by Puccinia striiformis. However, an unfavourable characteristic of T. sphaerococcum is its lower yield compared to bread wheat. Being a land race, the sphaerococcum wheat is poorly studied. This study was undertaken to increase knowledge of the physiology and genetics of this land race and determine if it may be possible to separate the favourable characters of T. sphaerococcum from its unfavourable characters. Plant height in bread wheat is controlled by many genes. ‘Reduced Height’ (Rht) genes which differ in their response to externally applied gibberellic acid (GA3) are responsible for the short stature of modern bread wheat varieties. Therefore, GA3 was used to probe the relationship between the semidwarf sphaerococcum phenotype and the Rht gene. T. sphaerococcum variety Sp5 showed a unique “seedling response” to externally applied GA3 when compared with T. aestivum varieties harbouring Rht1, Rht2, Rht8, Rht12, Rht13 or Rht18 alleles. A mapping population of doubled haploids was generated through wide hybridisation of F1 (Sp5 x Otane) with Zea mays. A genome-wide scan of Sp5 and Otane (parents) using 348 microsatellite (SSR) markers showed that only 169 of these markers (49%) were polymorphic between the parents. A DArT profiling yielded 348 markers that were polymorphic between the parents. Microsatellite markers and DArT markers were used to create a genetic map. The mapping population was phenotyped and a quantitative trait loci (QTL) analysis was performed for component traits of the complex sphaerococcum trait including plant height, spike length, awn length, yield, grain shape and crease size. Results of the QTL analysis indicated that it may be difficult to separate the favourable characters of T. sphaerococcum from its unfavourable characters through mutation because the component traits of the complex sphaerococcum trait may be under pleiotropic control of the Sp gene. The hypothesis that T. sphaerococcum originated through a mutation in T. aestivum was tested through induced mutation using gamma rays. Mutants from sphaerococcum-type to aestivum-type were isolated and phenotyped. Sphaerococcum-type mutants also were isolated and characterised from mutated aestivum-type wheat suggesting a possible origin of T. sphaerococcum through a mutation in T. aestivum.