During the last years rubber nanocomposites obtained by incorporating anisotropic clay nanoparticles within a rubber matrix to tailor material properties have attracted steadily growing interest. However, one main complication preventing rubber-clay nanocomposites from many potential applications is the difficulty to achieve a high degree of exfoliation particularly in case of melt mixing or compounding (using mixing equipment like internal mixer, two roll mills which can be up-scaled in industry). Albeit commercially available organomodified montmorillonite clays (OMt) are fairly compatible with the polar rubber like Acrylo-nitrile butadiene rubber (NBR), carboxylated nitrile rubber (XNBR), chloroprene rubber (CR) etc., its dispersion in non-polar rubbers like natural rubber (NR), is rather unsatisfactory. Incorporation of only 5 phr of OMt in NR by mechanical mixing leads to very poor dispersions with larger aggregates. Large agglomerates of OMt were observed with bare eyes throughout the matrix. Even in the TEM micrographs, highly agglomerated structures of clay particle were observed. A high degree of exfoliation of such clay is achieved in NR utilizing the so called ‘Propping-open approach’ where stepwise expansion of interlayer spacing of Mt took place. A series of long chain fatty acids (C16-C22) are intercalated into the interlayer space of OMt and a gradual expansion of the interlayer space were observed as the chain length of the fatty acid increased. Wide angle X-ray diffraction (WAXD), Fourier transform infrared spectroscopy (FTIR) and contact angle measurement indicated successful intercalation of the fatty acids into the interlayer space of the clay minerals. Since the fatty acid containing 22 carbon atoms has the largest interlayer distance among the modified samples studied, it has been selected for further study to understand the reinforcing behavior in NR matrix. An unusual mechanical percolation behavior of EOMt nanoparticles was observed in a NR matrix. The value of the mechanical percolation threshold (φp) and the fractal nature of nanoparticle clusters were determined through an analysis of the experimental data based on a theory put forward by Huber and Vilgis. This phenomenon was discussed in terms of fractal dimensions of the nanoparticle cluster. The impact of filler dispersion and rubber-filler interactions on the viscoelastic behavior of NR nanocomposites was systematically investigated. Significant non-linear viscoelastic behavior (Payne effect) was observed at very low EOMt content. Kraus and Maier-Göritz models were utilized to interpret such non-linear viscoelastic behavior. The nanocomposites showed enormous improvement in different physic-mechanical properties in the presence of EOMt. Technical elastomers are generally filled with certain fillers (e.g. carbon black) in order to reinforce the rubber matrix for some typical applications like tires, conveyer belts etc. Such rubber goods are always exposed to cyclic stress and deformations attributed to their dynamic application. Under constant and repeated applied stress, cracks develop at a stress concentration point, which could lead to ultimate failure. Therefore, the crack initiation and propagation behavior in such rubber products is very fundamental and need proper attention. The role of EOMt nanoparticles on the microstructure and fracture mechanical behavior of CB filled NR composites was investigated. Using pure-shear test specimen tear fatigue analysis (TFA) tests under cyclic conditions were carried out to explicate the crack growth behavior of CB filled NR in the presence of EOMt. A significant reduction in crack growth rate was noticed in the presence of only 5 phr of EOMt. Furthermore, instrumented tensile-impact tests (IT-IT) were also performed for the characterization of the crack resistance of the materials under impact-like loading conditions. / Die Einarbeitung von nur 5 phr organisch modifizierten Montmorillonite (OMt) in Naturkautschuk (NR) durch mechanisches Mischen führt zu einer sehr schlechten Verteilung mit größeren Aggregaten. Große Agglomerate von OMt waren mit bloßem Auge in der NR Matrix sichtbar. Sogar in TEM Aufnahmen wurden stark agglomerierte Strukturen beobachtet. Ein hoher Grad der Exfolierung von diesem Clay in NR wird durch die Nutzung des so genannten ‘Propping-open’ Ansatzes erreicht, in dem eine stufenweise Aufweitung des Zwischenschichtabstandes des OMt stattfindet. Eine Reihe langkettiger Fettsäuren (C16 – C22) wurde in die Zwischenschicht des OMt eingefügt. Mit zunehmender Kettenlänge der Fettsäuren wurde eine allmähliche Aufweitung der Zwischenschicht beobachtet. Da OMt, der mit einer Fettsäure mit 22 Kohlenstoffatomen modifiziert wurde, den größten Zwischenschichtabstand aller untersuchten Proben hatte, wurde diese Fettsäure für die weiteren Untersuchungen ausgewählt, um das Verstärkungsverhalten in der NR Matrix zu verstehen. Ein ungewöhliches Perkolationsverhalten der expandierten OMt (EOMt) Nanopartikel wurde in einer NR Matrix beobachtet. Der Wert der mechanischen Perkolationsschwelle (φp) und die fraktale Natur der Nanopartikel Cluster wurden durch eine Analyse der experimentellen Daten bestimmt, wobei eine Theorie, die von Huber und Vilgis vorangetrieben wurde, zur Anwendung kam. Dieses Phänomen wurde in Bezug auf die fraktalen Dimensionen der Nanopartikel Cluster diskutiert. Die Einfluss von EOMt Nanopartikel auf die Mikrostruktur und das mechanische Bruchverhalten von russgefüllten NR Kompositen wurde untersucht. Unter Verwendung reiner Schertestproben wurden Rissermüdungsanalysen unter zyklischer Belastung ausgeführt, um das Risswachstumsverhalten von russgefülltem NR in der Gegenwart von EOMt zu untersuchen und zu erklären. Eine signifikante Reduktion der Rissausbreitungsrate wurde in Gegenwart von nur 5 phr EOMt erreicht. Des Weiteren wurden auch instrumentierte Schlagzugprüfungen zur Charakterisierung des Risswiderstandes von Materialien unter schlagartigen Belastungsbedingungen durchgeführt.

The presented research report deals with the investigation of magnesium aluminum based layered double hydroxide (LDH) as a potential nanofiller and flame-retardant for polymers with special reference to polyethylene. LDH is a mixed hydroxide of di- and trivalent metal ions that crystallizes in the form of mineral brucite. The basic reason for selecting LDH or more specifically magnesium-aluminum based LDH (Mg-Al LDH) is their typical metal hydroxide-like chemistry and conventional clay-like layered crystalline structure. The former is helpful in the direct participation in flame inhibition through endothermic decomposition and stable char formation. On the other hand, the later makes LDH suitable for polymer nanocomposite preparation, which can address the poor dispersibility problem associated with conventional metal hydroxide type fillers in polyolefin matrix. Besides, unlike layered silicate type clays (often reported for their capability to improve flame retardancy of polymers), LDH being reactive during combustion has higher efficiency to reduce the heat released during combustion of the composites. LDH clay with fixed Al:Mg ratio was synthesized using urea hydrolysis method and characterized. The organic modification of Mg-Al LDH using anionic surfactants has been studied in details. The main purpose of such modification is to enlarge the interlayer distance and to render it more organophilic. The surfactants were selected based on their functionality, chain length, etc and the modification was carried out by regeneration method. In the modified LDHs, the surfactants anions are arranged as a monolayer in the interlayer region and expand the interlayer distance according to their tail size. PE/LDH nanocomposites were prepared by melt-compounding method using a co-rotating tightly intermeshed twin-screw extruder and the morphological, mechanical and flammability properties of the nanocomposites were investigated in details. The X-ray diffraction analysis and electron microscopic analysis show a complex LDH particle morphology with hierarchy of particle size and shape starting from exfoliated particles fragments to particle aggregates over few hundred nm size. The exfoliated LDH platelets are distributed both in the vicinity of large particles and also in the bulk matrix. The melt rheological characterization of the nanocomposites also reflects the similar complex particle morphology. The dynamic oscillatory shear experiments showed that with increasing LDH concentration, the rheological behavior of the nanocomposite melts deviates strongly from that of the unfilled polyethylene. Thermogravimetric analysis (TGA) shows that LDH significantly improves the thermal stability of the polymer matrix in comparison to the unfilled polymer. The flammability studies of the PE/LDH nanocomposites have been reported in terms of various standard methods, like limited oxygen index (LOI), cone-calorimetry and UL-94 vertical and horizontal burn tests. The cone-calorimetric investigation shows that the nanocomposites have significantly lower burning rate and heat released during combustion. With increasing concentration of LDH though the LOI value of the nanocomposite increases marginally, the burning behavior, like dripping, rate of burning, etc are significantly improved. The flammability performance of LDH in combination with other commonly used flame-retardant (magnesium hydroxide) was also investigated. It has been observed that in polyethylene, a 50 wt% combination filler (4:1 weight ratio of magnesium hydroxide and LDH) can provide similar flammability ratings (like V0 rating in UL94 test, no dripping, etc) as that observed with 60 wt% magnesium hydroxide alone.

Die inhärenten elastomeren Eigenschaften von Gummiwerkstoffen sind im Vergleich zu Thermoplasten in vielen Spezialanwendungen vorteilhaft. Jedoch sind ihre schlechten Reibungs- und Verschleißeigenschaften ein wesentlicher Nachteil besonders bei tribologischen Anwendungen. In der vorliegenden Arbeit wurden Reibung, Verschleiß und mechanische Eigenschaften von Gummiwerkstoffen, die Polytetrafluorethylen(PFTE)-Pulver enthalten, untersucht. Hauptziel war dabei die Verbesserung der Reibungs- und Verschleißeigenschaften bei weiterer Erhöhung der mechanischen Eigenschaften der Elastomere. Es ist bekannt, dass sich Reibungs- und Verschleißeigenschaften gummiähnlicher Materialien in vielfältiger Weise von den Reibungseigenschaften der meisten anderen Festkörper unterscheiden. Die Gründe dafür sind das viskoelastische Verhalten und der sehr geringe elastische Modul von Gummi. Die Verwendung von mit Elektronen modifizierten PTFE-Pulvern in Ethylen-Propylen-Dien-Monomer (EPDM) Kautschuken führt zu einer signifikanten Reduzierung der Reibung, Erhöhung der Verschleißfestigkeit und gleichzeitig zu verbesserten mechanischen Eigenschaften in Folge einer speziellen chemischen Kopplung zwischen dem modifiziertem PTFE-Pulver und dem EPDM. Gummirezeptur, Vernetzungsmethode und die viskoelastischen Materialeigenschaften beeinflussen wesentlich die tribologischen und mechanischen Eigenschaften. Morphologie, Dispersion und die chemische Kopplung des PTFE-Pulvers haben einen signifikanten Einfluss auf die Reibungs- und Verschleißverhalten. Die viskoelastischen Materialeigenschaften, d.h. Härte, E-Modul und tan delta (Verlustfaktor) der Gummimischungen sind kritische Parameter und erfordern deshalb eine Optimierung. In dieser Arbeit wurden zwei Modellsysteme untersucht, die auf zwei unterschiedlichen Kautschuktypen basieren: a) Ethylen-Propylene-Diene-Monomer (EPDM) Kautschuk und b) Polychloropren Kautschuk (CR). / The inherent elastomeric properties of rubber compounds in comparison to thermoplastics are advantageous in many special purpose applications. However, their characteristic poor friction and wear properties are of prime concern especially in tribological applications. In the present work, friction, wear and mechanical properties of rubber compounds based on PTFE powder have been investigated. The main aim was to improve the friction and wear properties while further enhancing the mechanical properties of rubber compounds. As known, friction and wear behaviour of rubber-like materials differ in many ways from the frictional properties of most other solids. The reason for this is the high viscoelasticity and very low elastic modulus of rubber. The use of electron-modified PTFE powder in EPDM results in significant improvement in reducing friction, enhancing wear resistance and simultaneously improving mechanical properties due to specific chemical coupling between modified PTFE powder and EPDM. The rubber formulation, crosslinking mode and bulk viscoelastic properties strongly influences friction, wear and mechanical properties. The morphology, dispersion, and specific chemical coupling of PTFE powder play a significant role on friction and wear behaviour. The bulk viscoelastic properties, i.e. hardness, modulus and tan delta (loss factor) of the compounds are critical parameters and therefore, requires optimization. In this work two model systems based on two different rubber matrixes i.e. Ethylene-Propylene-Diene-Monomer (EPDM) and Chloroprene (CR) rubber have been investigated.

In der Dissertation wurden Nanokomposite mit unterschiedlichen Kautschuken (HNBR, EPDM, MAH-g-EPDM) als Basismaterial sowie diversen modifizierten Schichtsilikaten als Füllstoff hergestellt und charakterisiert. Untersucht wurden die sich ausbildenden Strukturen bzw. die Morphologie (Aggregation, mögliche Orientierungen), die mechanischen Eigenschafte (Verstärkungswirkung) sowie die Füllstoff-Füllstoff-Wechselwirkungen und die Polymer-Füllstoff-Wechselwirkungen.

Block copolymers are commercially significant and fundamentally interesting class of polymeric materials. The ability to undergo interfacial thermodynamics-controlled microphase separation from a completely disordered state in the melt to a specifically defined ordered structure through self-organization makes the block copolymers based materials unique. Block copolymer are strongly replacing many of the commercially available polymers due to their unique microstructure and properties. The most practical interests of block copolymers lie in the area of thermoplastic elastomers (TPEs). The objective of the present thesis work is to developing novel roots for enhancing the physical and mechanical properties in block copolymer and multigraft copolymers. Initially the properties are tailored by controlling chemical architecture at synthesis level and by selective blending at production level. This gives an easy access for improvement of the material properties and this is one of my major tasks in the present research modules. Further the block copolymer based TPEs are cross-linked in presence of electron beam (EB) radiation for developing materials with superior properties. The electron beam radiation has the ability to alter material parameters at molecular level for enhancing the macroscopic properties. The desirable physical and chemical properties can be easily attained by varying the radiation beam parameters. In addition to that, controlling the material at nanometer scale is one of the greatest challenges for current nanocomposite research. In elastomeric materials it is very prominent to fill the rubber matrix with nano particles from carbon or silica by melt mixing technique for enhancing the material properties. Other than conventional melt mixing technique, sol–gel processing is also a versatile technique, which making it possible to produce a wide variety of materials and to provide existing materials with novel properties. A combination of in situ sol-gel reaction with electron beam cross-linking in TPEs from triblock copolymer has been demonstrated for the first time as one of the novel nanocomposite system in this work. The main advantage of this system lies in controlling the material behaviour by finely tuning the size of silica nano particle generated inside TPE during in situ sol-gel reaction. Finally, the various roots employed for enhancing the material behaviour in block copolymers in the above research module were secussfully employed on super elastic multigraft copolymers for improving their strength withour sacrificing the super elastic nature.

Thermoplastic Vulcanizates (TPVs) are itself a commercially high valued group of polymer blend. They render technological properties of conventional vulcanized elastomers with the ease of thermoplastic melt (re)processability. With ever growing market, TPVs have got plenty of applications among various fields. Here, the technological properties of these TPVs were tailored according to the purpose by interplaying physical parameters of polymers and advanced high energy electron technology. Electron irradiation, though a well-known technique for cross-linking in polymer industry, is only restricted to final product treatment. We take it to the next level by coupling a conventional internal mixer and a high energy electron accelerator. Polypropylene (PP) and natural rubber (NR) based TPVs have been prepared using this new reactive processing technology, named Electron Induced Reactive Processing (EIReP). Various electron treatment parameters were explored to maximize technological properties of TPVs. Effects of various polyfunctional monomers (PFM) were also studied. In an endeavor to develop a potential method for customization, deep insights of macroscopic and microscopic structure of these TPVs were presented with the help of various advanced scientific characterization techniques. Commonly faced difficulties like viscosity mismatch, cure rate mismatch, and incompatibility due to different molecular structures were furnished along with plausible solutions. Investigation of phase inversion from co-continuous matrix to thermoplastic matrix was dealt with special care as it helps to understand structure property correlation for all TPVs. To make the whole effort relevant, at the end of this thesis a summary of various technological properties has been given for the newly processed and commercially available TPVs.

Polyurethane and the analogous ‘polyurethane-urea’ are high performance polymeric materials having remarkable properties such as high stiffness, abrasion and tear strengths. In many studies, the low strength rubbers have been blended with various types of polyurethanes for new and improved materials. However, until now, the reported heterogeneous blends offer only a narrow temperature range of application due to the high temperature softening of their polyurethane (-urea) phase. In addition, the conventional solution-or melt-blending methods are time and energy intensive, which tend to forfeit the economical realization of the reported blends. In contrast to earlier studies, a simplified reactive blending process is suggested to synthesize polyurethane-urea via a prepolymer route during blending with rubbers to obtain novel elastomeric materials having extended performance characteristics. The reactive blending process is opted to prepare blends based on nitrile butadiene rubber (NBR) and in-situ synthesized polyurethane-urea (PUU). The blending is carried out in an internal mixer at a preset temperature of 100°C. The critical temperatures of the reactive blending process are determined from the chemo-rheological analysis of a premix, composed of a 4,4′-diphenylmethane diisocyanate (MDI)/polyether (PTMEG) based prepolymer admixed with 1,3-phenylene diamine (mPD). The prepared NBR/PUU blends exhibit highly improved mechanical properties. Contrary to previous reports, the reinforced dynamic-mechanical responses of the novel blends remain stable till very high temperatures (≥180°C). The influence of diamine type on the in-situ synthesized polyurethane-urea and the performance of prepared blends are investigated. Four different diamines, namely 1,3-Phenylene diamine, 1,4-Bis(aminomethyl)benzene, 4,4′-Methylene-bis(2-chloroaniline) and 4,4ʹ-(1,3-Phenylenediisopropylidene)bisaniline, are selected to chain extend the prepolymer to PUU during blending with NBR. The chemical and domain structure of the PUUs are found to greatly influence the reinforced tensile and dynamic-mechanical responses of the NBR/PUU 70/30 blends. The PUU (based on MDI/PTMEG prepolymer and mPD) is blended with polar (CR, XNBR) and nonpolar (NR, EPDM, sSBR) rubbers. PUU compatibilizes with all the rubbers irrespective of their polarity and reinforces their tensile and dynamic-mechanical characteristics. The use of blends in industrial applications, for example, in a truck tire tread compound and as a roller covering material, is examined. In a simplified tire tread formulation, the carbon black for NR-CB composite is partially replaced with an equivalent quantity of PUU for NR/PUU-CB composite of similar hardness. The dynamic mechanical investigations reveal that the energy dissipation and strain dependent softening is high in NR-CB as compared to the NR/PUU-CB composite. In another application, NBR/PUU blend is successfully tested as a rubber roller covering material. The tested blend-covered roller retains its structural integrity and develops less heat build-up as compared to the silica filled NBR-covered roller. This shows a substantial suitability of the blend-covered rollers for film, printing and textile processing machinery. These novel blends are considered to be the promising new materials for many commercial applications including wheels, rubber rollers, belts or pump impellers.

Isotactic polypropylene (iPP), as one of the most versatile commodity thermoplastic polymers, is a polymorphic material having several crystal modifications, among which the β-form exhibits higher performance including excellent impact strength and improved elongation at break.Up to now, the effective and convenient way to prepare the iPP with high content of β-phase has been successfully achieved by addition of certain β-nucleating agent. Since the coexistence of β-nucleating agent and flow (shear flow, extensional flow or mixed), which usually exists in common industrial processing, makes the crystallization process more complex, their combined effect on the structure evolution of polymers, especially in the early stage of crystallization is still not well understood. The mechanical properties of iPP depend strongly on its crystallinity, crystal orientation and morphology determined by the conditions during preparation. On the other hand, the mechanical properties of polymers can also be modulated by deformation processing, which is directly related to the deformation-induced structure transition. However, the transition mechanism of different crystal forms and structure-property correlation still remain unclear. In this thesis, time-resolved synchrotron X-ray scattering was firstly used for the in-situ study of the structural and morphological developments of β-nucleated iPP during shear-induced crystallization. It was found that the crystallization process was strongly influenced by the concentration of β-nucleating agent, shear rate and shear temperature. Then extension-induced crystallization was investigated by a novel melt draw experiment, where a different crystallization mechanism compared to the shear-induced crystallization was found. Subsequently, β-nucleated iPP samples with different thermomechanical histories were scanned by synchrotron X-ray microbeam to construct their overall morphological distributions, including distributions of crystallinity, lamellar thickness, orientation, etc. Finally, these morphology-identified samples were investigated by in-situ synchrotron X-ray measurements coupled with mechanical testing to follow the structure evolution during deformation at elevated temperature. It was found that the deformation behaviour of β-nucleated iPP was closely associated with its initial morphology, its subsequent variation during stretching as well as the stretching conditions including the stretching rate and stretching temperature. The current study would not only contribute to the development of crystallization and deformation theory but also be beneficial for the material design.