Nowadays, Sigma-Delta analog-to-digital converters have been widely used in the technology of analog-to-digital conversion. It depends on the merits that the approach of Sigma-Delta has. The signal converted by oversampling is precise and well-suited in signal processing systems.This thesis mainly focuses on the principles and simulations of fundamental first-order Sigma-Delta converter, and some brief introductions about other Sigma-Delta converters.The main researches of this thesis are as follows: (1)This thesis shows not only the path about development of technology of different ADCs, but also the features and principles of these ADCs and their structures. (2)The thesis discusses how the technologies of oversampling and noise shaping are used in Sigma-Delta analog-to-digital conversion. (3)Illustrate different orders Sigma-Delta converters in different bits and their advantages and disadvantages, respectively. (4)The simulation is given in Matlab(Simulink). Typical first-order SigmaDelta converter is simulated with additional noise which will impact the input signal when implement. / Sigma-Delta Converter

The mixed-signal and analog design on a pre-diffused array is a challenging task, given that the digital array is a linear matrix arrangement of minimum-length transistors. To surmount this drawback a specific discipline for designing analog circuits over such array is required. An important novel technique proposed is the use of TAT (Trapezoidal Associations of Transistors) composite transistors on the semi-custom Sea-Of-Transistors (SOT) array. The analysis and advantages of TAT arrangement are extensively analyzed and demonstrated, with simulation and measurement comparisons to equivalent single transistors. Basic analog cells were also designed as well in full-custom and TAT versions in 1.0mm and 0.5mm digital CMOS technologies. Most of the circuits were prototyped in full-custom and TAT-based on pre-diffused SOT arrays. An innovative demonstration of the TAT technique is shown with the design and implementation of a mixed-signal analog system, i. e., a fully differential 2nd order Sigma-Delta Analog-to-Digital (A/D) modulator, fabricated in both full-custom and SOT array methodologies in 0.5mm CMOS technology from MOSIS foundry. Three test-chips were designed and fabricated in 0.5mm. Two of them are IC chips containing the full-custom and SOT array versions of a 2nd-Order Sigma-Delta A/D modulator. The third IC contains a transistors-structure (TAT and single) and analog cells placed side-by-side, block components (Comparator and Folded-cascode OTA) of the Sigma-Delta modulator.

The mixed-signal and analog design on a pre-diffused array is a challenging task, given that the digital array is a linear matrix arrangement of minimum-length transistors. To surmount this drawback a specific discipline for designing analog circuits over such array is required. An important novel technique proposed is the use of TAT (Trapezoidal Associations of Transistors) composite transistors on the semi-custom Sea-Of-Transistors (SOT) array. The analysis and advantages of TAT arrangement are extensively analyzed and demonstrated, with simulation and measurement comparisons to equivalent single transistors. Basic analog cells were also designed as well in full-custom and TAT versions in 1.0mm and 0.5mm digital CMOS technologies. Most of the circuits were prototyped in full-custom and TAT-based on pre-diffused SOT arrays. An innovative demonstration of the TAT technique is shown with the design and implementation of a mixed-signal analog system, i. e., a fully differential 2nd order Sigma-Delta Analog-to-Digital (A/D) modulator, fabricated in both full-custom and SOT array methodologies in 0.5mm CMOS technology from MOSIS foundry. Three test-chips were designed and fabricated in 0.5mm. Two of them are IC chips containing the full-custom and SOT array versions of a 2nd-Order Sigma-Delta A/D modulator. The third IC contains a transistors-structure (TAT and single) and analog cells placed side-by-side, block components (Comparator and Folded-cascode OTA) of the Sigma-Delta modulator.

The mixed-signal and analog design on a pre-diffused array is a challenging task, given that the digital array is a linear matrix arrangement of minimum-length transistors. To surmount this drawback a specific discipline for designing analog circuits over such array is required. An important novel technique proposed is the use of TAT (Trapezoidal Associations of Transistors) composite transistors on the semi-custom Sea-Of-Transistors (SOT) array. The analysis and advantages of TAT arrangement are extensively analyzed and demonstrated, with simulation and measurement comparisons to equivalent single transistors. Basic analog cells were also designed as well in full-custom and TAT versions in 1.0mm and 0.5mm digital CMOS technologies. Most of the circuits were prototyped in full-custom and TAT-based on pre-diffused SOT arrays. An innovative demonstration of the TAT technique is shown with the design and implementation of a mixed-signal analog system, i. e., a fully differential 2nd order Sigma-Delta Analog-to-Digital (A/D) modulator, fabricated in both full-custom and SOT array methodologies in 0.5mm CMOS technology from MOSIS foundry. Three test-chips were designed and fabricated in 0.5mm. Two of them are IC chips containing the full-custom and SOT array versions of a 2nd-Order Sigma-Delta A/D modulator. The third IC contains a transistors-structure (TAT and single) and analog cells placed side-by-side, block components (Comparator and Folded-cascode OTA) of the Sigma-Delta modulator.

Research Doctorate - Doctor of Philosophy (PhD) / This thesis presents results on optimal coding and decoding of discrete-time stochastic signals, in the sense of minimizing a distortion metric subject to a constraint on the bit-rate and on the signal transfer function from source to reconstruction. The first (preliminary) contribution of this thesis is the introduction of new distortion metric that extends the mean squared error (MSE) criterion. We give this extension the name Weighted-Correlation MSE (WCMSE), and use it as the distortion metric throughout the thesis. The WCMSE is a weighted sum of two components of the MSE: the variance of the error component uncorrelated to the source, on the one hand, and the remainder of the MSE, on the other. The WCMSE can take account of signal transfer function constraints by assigning a larger weight to deviations from a target signal transfer function than to source-uncorrelated distortion. Within this framework, the second contribution is the solution of a family of feedback quantizer design problems for wide sense stationary sources using an additive noise model for quantization errors. These associated problems consist of finding the frequency response of the filters deployed around a scalar quantizer that minimize the WCMSE for a fixed quantizer signal-to-(granular)-noise ratio (SNR). This general structure, which incorporates pre-, post-, and feedback filters, includes as special cases well known source coding schemes such as pulse coded modulation (PCM), Differential Pulse-Coded Modulation (DPCM), Sigma Delta converters, and noise-shaping coders. The optimal frequency response of each of the filters in this architecture is found for each possible subset of the remaining filters being given and fixed. These results are then applied to oversampled feedback quantization. In particular, it is shown that, within the linear model used, and for a fixed quantizer SNR, the MSE decays exponentially with oversampling ratio, provided optimal filters are used at each oversampling ratio. If a subtractively dithered quantizer is utilized, then the noise model is exact, and the SNR constraint can be directly related to the bit-rate if entropy coding is used, regardless of the number of quantization levels. On the other hand, in the case of fixed-rate quantization, the SNR is related to the number of quantization levels, and hence to the bit-rate, when overload errors are negligible. It is shown that, for sources with unbounded support, the latter condition is violated for sufficiently large oversampling ratios. By deriving an upper bound on the contribution of overload errors to the total WCMSE, a lower bound for the decay rate of the WCMSE as a function of the oversampling ratio is found for fixed-rate quantization of sources with finite or infinite support. The third main contribution of the thesis is the introduction of the rate-distortion function (RDF) when WCMSE is the distortion metric, denoted by WCMSE-RDF. We provide a complete characterization for Gaussian sources. The resulting WCMSE-RDF yields, as special cases, Shannon's RDF, as well as the recently introduced RDF for source-uncorrelated distortions (RDF-SUD). For cases where only source-uncorrelated distortion is allowed, the RDF-SUD is extended to include the possibility of linear-time invariant feedback between reconstructed signal and coder input. It is also shown that feedback quantization schemes can achieve a bit-rate only 0.254 bits/sample above this RDF by using the same filters that minimize the reconstruction MSE for a quantizer-SNR constraint. The fourth main contribution of this thesis is to provide a set of conditions under which knowledge of a realization of the RDF can be used directly to solve encoder-decoder design optimization problems. This result has direct implications in the design of subband coders with feedback, as well as in the design of encoder-decoder pairs for applications such as networked control. As the fifth main contribution of this thesis, the RDF-SUD is utilized to show that, for Gaussian sta-tionary sources with memory and MSE distortion criterion, an upper bound on the information-theoretic causal RDF can be obtained by means of an iterative numerical procedure, at all rates. This bound is tighter than 0:5 bits/sample. Moreover, if there exists a realization of the causal RDF in which the re-construction error is jointly stationary with the source, then the bound obtained coincides with the causal RDF. The iterative procedure proposed here to obtain Ritc(D) also yields a characterization of the filters in a scalar feedback quantizer having an operational rate that exceeds the bound by less than 0:254 bits/sample. This constitutes an upper bound on the optimal performance theoretically attainable by any causal source coder for stationary Gaussian sources under the MSE distortion criterion.

Research Doctorate - Doctor of Philosophy (PhD) / This thesis presents results on optimal coding and decoding of discrete-time stochastic signals, in the sense of minimizing a distortion metric subject to a constraint on the bit-rate and on the signal transfer function from source to reconstruction. The first (preliminary) contribution of this thesis is the introduction of new distortion metric that extends the mean squared error (MSE) criterion. We give this extension the name Weighted-Correlation MSE (WCMSE), and use it as the distortion metric throughout the thesis. The WCMSE is a weighted sum of two components of the MSE: the variance of the error component uncorrelated to the source, on the one hand, and the remainder of the MSE, on the other. The WCMSE can take account of signal transfer function constraints by assigning a larger weight to deviations from a target signal transfer function than to source-uncorrelated distortion. Within this framework, the second contribution is the solution of a family of feedback quantizer design problems for wide sense stationary sources using an additive noise model for quantization errors. These associated problems consist of finding the frequency response of the filters deployed around a scalar quantizer that minimize the WCMSE for a fixed quantizer signal-to-(granular)-noise ratio (SNR). This general structure, which incorporates pre-, post-, and feedback filters, includes as special cases well known source coding schemes such as pulse coded modulation (PCM), Differential Pulse-Coded Modulation (DPCM), Sigma Delta converters, and noise-shaping coders. The optimal frequency response of each of the filters in this architecture is found for each possible subset of the remaining filters being given and fixed. These results are then applied to oversampled feedback quantization. In particular, it is shown that, within the linear model used, and for a fixed quantizer SNR, the MSE decays exponentially with oversampling ratio, provided optimal filters are used at each oversampling ratio. If a subtractively dithered quantizer is utilized, then the noise model is exact, and the SNR constraint can be directly related to the bit-rate if entropy coding is used, regardless of the number of quantization levels. On the other hand, in the case of fixed-rate quantization, the SNR is related to the number of quantization levels, and hence to the bit-rate, when overload errors are negligible. It is shown that, for sources with unbounded support, the latter condition is violated for sufficiently large oversampling ratios. By deriving an upper bound on the contribution of overload errors to the total WCMSE, a lower bound for the decay rate of the WCMSE as a function of the oversampling ratio is found for fixed-rate quantization of sources with finite or infinite support. The third main contribution of the thesis is the introduction of the rate-distortion function (RDF) when WCMSE is the distortion metric, denoted by WCMSE-RDF. We provide a complete characterization for Gaussian sources. The resulting WCMSE-RDF yields, as special cases, Shannon's RDF, as well as the recently introduced RDF for source-uncorrelated distortions (RDF-SUD). For cases where only source-uncorrelated distortion is allowed, the RDF-SUD is extended to include the possibility of linear-time invariant feedback between reconstructed signal and coder input. It is also shown that feedback quantization schemes can achieve a bit-rate only 0.254 bits/sample above this RDF by using the same filters that minimize the reconstruction MSE for a quantizer-SNR constraint. The fourth main contribution of this thesis is to provide a set of conditions under which knowledge of a realization of the RDF can be used directly to solve encoder-decoder design optimization problems. This result has direct implications in the design of subband coders with feedback, as well as in the design of encoder-decoder pairs for applications such as networked control. As the fifth main contribution of this thesis, the RDF-SUD is utilized to show that, for Gaussian sta-tionary sources with memory and MSE distortion criterion, an upper bound on the information-theoretic causal RDF can be obtained by means of an iterative numerical procedure, at all rates. This bound is tighter than 0:5 bits/sample. Moreover, if there exists a realization of the causal RDF in which the re-construction error is jointly stationary with the source, then the bound obtained coincides with the causal RDF. The iterative procedure proposed here to obtain Ritc(D) also yields a characterization of the filters in a scalar feedback quantizer having an operational rate that exceeds the bound by less than 0:254 bits/sample. This constitutes an upper bound on the optimal performance theoretically attainable by any causal source coder for stationary Gaussian sources under the MSE distortion criterion.