M.Ing. / In this study a comparison is made between the punching shear capacities of square slabs reinforced with 3CR 12 corrosion resisting stainless steel and high tensile strength carbon steel. A square column 11 0 mm x 11 0 mm is used to simulate the point load on the slab. Three different slab depths were chosen for the experimental procedure. The South African concrete design specification SABS 0 I 00, the Eurocode concrete design specification and Menetrey's design model are used to determine the theoretical punching shear capacities of the slabs. It is concluded in this study that the procedures described in the concrete design codes and by Menetrey to determine the punching shear stress of concrete slabs reinforced with high strength carbon steel reinforcing bar compare well with the experimental results when 3CR I 2 corrosion resisting steel is used as reinforcing bar in concrete. The experimental results do not compare well with the theoretical results when the new Eurocode is used.

The mitigation of blast hazards on critical reinforced concrete structures has become a major concern in regards to the safety of people and the integrity of buildings. Recent terrorist incidents and accidental explosions have demonstrated the need to study the effects of such threats on structures in order to develop effective methods of reducing the overall impact of blast loads. With the arrival of innovative materials such as steel fibre reinforced concrete (SFRC), ultra-high performance fibre reinforced concrete (UHPFRC) and high strength steel reinforcement, research is required in order to successfully adapt these new materials in blast-resistant structures. Hence, the objective of this thesis to conduct an experimental parametric study with the purpose of investigating the implementation of these innovative materials in reinforced concrete slabs and panels. As part of the study, a total of fourteen one-way slab specimens with different combinations of concrete, steel fibres and steel reinforcement are tested under simulated blast loads using the University of Ottawa Shock-Tube Facility. The test program includes three slabs constructed with normal-strength concrete, five slabs constructed with SFRC and six slabs constructed with UHPFRC. Among these specimens, four are reinforced with high-performance steel reinforcement. The specimens are subjected to repeated blast loading with gradually increasing reflected pressure and reflected impulse until failure. The performance of the slabs is studied using various criteria such as failure load and mode, maximum and residual deflections, as well as tensile cracking, spalling and secondary fragmentation control. The behaviour of all specimens is compared in different categories to determine the effects of concrete type, steel reinforcement type, steel fibre content and steel fibre type on blast performance. As part of the analytical study the response of the slab specimens is predicted using dynamic inelastic single-degree-of-freedom (SDOF) analysis. The dynamic analysis is conducted by generating load-deformation resistance functions for the slabs incorporating dynamic material properties.

Steel Fibre Reinforced Concrete (SFRC) is defined as concrete containing randomly oriented discrete steel fibres. The main incentive of adding steel fibres to concrete is to control crack propagation and crack widening after the concrete matrix has cracked. Control of cracking automatically improves the mechanical properties of the composite material (SFRC). The most significant property of SFRC is its post-cracking strength that can impart the ability to absorb large amounts of energy before collapse. Ground slabs are structural applications that could benefit from these advantageous features of the SFRC. Many tests on SFRC ground slabs show that the material can offer distinct advantages compared to plain concrete. In concrete road pavements, SFRC is particularly suitable for increasing load-carrying capacity and fatigue resistance. Not surprisingly, recent years have witnessed acceleration in full-scale tests of SFRC and eventually acceptance of its use in concrete pavements. The use of SFRC in pavements has been slowed down by the absence of a reliable theoretical model to analyse and design these pavements. The analysis of ground slabs has traditionally been based on an elastic analysis assuming un-cracked concrete. Using such a method for SFRC would ignore the post-cracking contribution the SFRC can make to the flexural behaviour of the slab. Despite the growing trend of using methods of analysis based on yield-line theory, which can consider the post-cracking strength of SFRC, these methods were also found to underestimate the load-carrying capacity of SFRC ground slabs. To effectively account for the post-cracking strength of SFRC in the analysis of such slabs requires a method such as the finite element method. In the present work, non-linear methods are used to model the behaviour of SFRC ground slabs subjected to mechanical load. An analytical method is used to determine a tensile stress-strain response for SFRC. In this method, the post-cracking strength of SFRC is taken into account and hence the material model is sensitive to the element size used. The calculated stress-strain response is utilised in finite element analysis of SFRC beams and ground slabs. A smeared crack approach is used to simulate the behaviour of concrete cracking. The analytical method used to determine the tensile stress-strain response, as well as the finite element model, are evaluated using results from experiments on SFRC beams and ground slabs. The analytical results are found to compare well with the observations. The non-linear methods are further used to study the effect of the material model parameters as well as the support stiffness on load-displacement behaviour of SFRC ground slabs. The developed finite element model is shown to be more efficient compared to methods based on the yield-line theory. This is because it produces the load-displacement behaviour of the SFRC ground slab up to a reasonable limit and it provides the tensile stresses as well as the extent of cracking of the slab at every point on the load-displacement response. Using the developed finite element model will allow for considerable material saving since smaller slab thickness can be calculated compared to analytical models currently in use. / Thesis (PhD(Transportation Engineering))--University of Pretoria, 2008. / Civil Engineering / PhD / unrestricted

The continuous population increase in recent years requires a greater number of households to be built quickly, with good materials and produced under quality standards that guarantee their manufacturing process. The prefabricated concrete, produced and supplied by concrete plants, is poured into the different structural elements, the mezzanine slabs being the most careful surfaces in the appearance of fissures; because being horizontal and having larger dimensions, the dimensional changes in the concrete appear more frequently due to the rapid loss of water from the surface of the concrete before setting; which generates superior stresses to the resistant capacity of the concrete at early ages, which affect the durability and reduce the resistance of the structures, causing greater economic expenses in maintenance and repairs. In the present investigation, 5%, 10% and 15% of rice husk ash was used as a replacement for cement and 900g/m3 of polypropylene fiber; The results indicate that as the percentage of rice husk ash increases, there is a reduction in the slump and the crack fissures, and that the resistance to compression and flexion decreases, with respect to the concrete pattern.

Bibliography: pages 128-132. / A micro-computer based package for the analysis and design of prestressed flat slabs is presented. The constant strain triangle and the discreet Kirchhoff plate bending triangle are combined to provide an efficient "shell" element. These triangles are used for the finite element analysis of prestressed flat slabs. An efficient out-of-core solver for sets of linear simultaneous equations is presented. This solver was developed especially for micro-computers. Subroutines for the design of prestressed flat slabs include the principal stresses in the top and bottom fibres of the plate, Wood/Armer moments and untensioned steel areas calculated according to Clark's recommendations. Extensive pre- and post-processing facilities are presented. Several plotting routines were developed to aid the user in his understanding of the behaviour of the structure under load and prestressing.

No description available.

No description available.

No description available.

No / In composite steel beams with precast hollow core slabs, the amount of transverse reinforcement can have a significant effect on the shear and slip capacity of the mechanical shear connectors. The issue of connector ductility becomes especially important when partial shear connection is adopted, as premature failure of the shear connectors would lead to sudden failure of the composite beam. This chapter presents its findings on the effect of transverse reinforcement on connector ductility and proposes design equations. Transverse reinforcement is used to provide ties for the slabs and confined concrete from splitting. The ductility of the shear connector, that is, slip capacity is directly affected by the amount of transverse reinforcement. Design equations presented in this chapter for estimating the shear capacity of the headed shear stud show a good correlation with the push-off test results. For full shear connection design, pre-splitting shear capacity of the headed stud can be used for the composite design, while for partial shear connection design, post-splitting shear capacity of the headed stud should be used. In general, a minimum transverse reinforcement of T16 bars should be used if partial shear connection design is used to ensure a minimum ductility of 6mm slip.

No