Fresh properties of mortars are important factors in altering the performance of self compacting concrete (SCC). Measurement of the rheological properties of the fine mortar part of concrete is generally used in the mix design of SCC. It can be stated that SCC rheology can be optimized if the fine mortar part of concrete is designed properly. However, measurement of the rheological properties is often impractical due to the need for complex equipment. Therefore, more practical methods of assessing mortar workability are often preferred. In this study, four mineral admixtures, three superplasticizers (SP) and two viscosity modifying admixtures (VMA) were used to prepare self compacting mortar (SCM). The mineral admixtures included fly-ash, brick powder, limestone powder, and kaolinite. Two of the SPs were polycarboxylate based and another one was melamine formaldehyde based. One of the viscosity modifying admixtures was based on an aqueous dispersion of microscopic silica and the other one was based on high molecular weight hydroxylated polymer. Within the scope of the experimental program, 43 mixes of SCM were prepared from different materials with keeping the amount of mixing water constant. Workability of the fresh mortar were determined using V - funnel and slump flow tests. The setting time of the mortars, were also determined. The hardened properties that were determined included the ultrasonic pulse velocity (UPV) and the strength which was determined at 7, 28, and 56 days. It was concluded that among the mineral admixtures used, only fly-ash and limestone powder increased the workability of the mixes. The two polycarboxylate based SPs yield approximately the same workability and the melamine formaldehyde based SP was not as effective as the other two.

Att gjuta med betong under vatten är utmanande, och det ställs höga krav på både betongen och utförandet för att resultatet ska bli bra. Peab Anläggning har uppmärksammat en del problem med denna typ av gjutningar och ville därför tydliggöra problematiken för att öka chansen för bra resultat vid framtida undervattensgjutningar. Problemen bestod dels av gjutskador på den färdiga betongkonstruktionen, och dels av problem med betongen under gjutningens gång i form av skum och separation. Examensarbetet sammanställer svårigheterna med undervattensgjutning med självkompakterande betong (SKB) och undersöker vilka faktorer som påverkar det färdiga gjutresultatet. Detta har gjorts genom en litteraturstudie, intervjuer med kunniga personer inom ämnet samt besök på arbetsplatser där undervattensgjutningar utförts. De svårigheter som identifierats delas in under fyra huvudrubriker; planering inför gjutning, betong, form samt utförande. Planeringen inför gjutningen är mycket viktig men svår då många faktorer måste tas hänsyn till, såsom väder och trafik. För att minimera risken för oönskade gjutuppehåll krävs det även en förberedande plan med lösningar på problem som kan uppstå under gjutdagen. Svårigheten med färsk betong är att det är ett levande och därmed oförutsägbart material. Det är nödvändigt att betongen har god sammanhållning så att betongens cementpasta inte vaskas ut i vattnet. Det är även viktigt att betongen har rätt konsistens för att kunna omsluta all armering och fylla ut hela formen. Betongen testas när den kommer till arbetsplatsen. Bland annat kontrolleras betongens lufthalt samt homogenitet och flytbarhet, det senare med hjälp av flytsättmått. Det är viktigt att ta hänsyn till dessa kontroller och att ta beslutet att inte gjuta med dålig betong. Det ställs även höga krav på formen vid undervattensgjutningar. Den måste vara helt tät och byggas på rätt sätt så att skum och bottenslam kan rinna ut ur formen. En svårighet är att dykarna behöver utföra en del av formbyggandet under vattenytan. Utförandet är en stor utmaning, då arbetsmomentet är komplicerat och man gjuter i blindo. Metoden går ut på att betong pumpas ner under vattenytan genom ett betongrör med en undervattensventil. Under gjutningens gång är det viktigt att rörets mynning hela tiden är under betongytan och att gjutröret hålls vertikalt. Slutligen är det värt att nämna att litteraturen som finns idag om undervattensgjutningar är bristfällig, något som gör det svårt att lära sig om ämnet. De förslag på lösningar som grundas på slutsatsen är att all betong som kommer till arbetsplatsen bör testas, trots att det inte alltid är ett krav. Detta så att ett beslut kan tas kring varje enskilt betonglass om betongen är godkänd att gjuta med. För att öka chansen att betongen har önskade egenskaper är det viktigt att betongbilen som levererar betongen till arbetsplatsen är ren och inte innehåller rester av annan betong. Det krävs under hela arbetet en god kommunikation mellan både pumpmaskinist, dykare och arbetsledning för att de gemensamt ska kunna lösa eventuella problem som uppstår. Slutligen rekommenderas att ta hjälp av varandra och dra nytta av den kompetens och erfarenhet som finns inom företaget. / Casting with concrete under water is challenging, and requires high standards on both the concrete and the work practice to achieve good results. Peab noticed problems with this type of casting, and wanted to clarify the difficulties to increase the chance of good results with future underwater castings. The problems were injuries on the finished concrete structure and troubles with the concrete during casting such as foam and separation in the concrete. This paper compiles the difficulties with underwater casting with self-consolidating concrete (SCC) and investigates the factors that affect the final result. This has been done through interviews with experienced people, a literature review and visits to construction site that performed underwater casting. This paper identifies four main issues; pre-casting planning, concrete quality, form and work procedure. The planning is very important but difficult, as many factors need to be considered, such as weather, land traffic and boat traffic. In order to minimize the risk of unwanted breaks during casting, it is good to have a preparatory plan with solutions to problems that may occur. The difficulty with concrete is that it's a living, and thus unpredictable, material. It is very important that the concrete has good cohesion so that the concrete's cement paste is not washed out in the water. It is also necessary that the concrete has good consistency to ensure it will enclose all reinforcement and fill in the entire form. The concrete is tested when it arrives to the construction site. Among other things, the air content as well as homogeneity and flowability are controlled, the latter controlled by a slump flow test. It is important to take these controls into consideration, and to make the decision not to cast with bad concrete. The requirements on the form used during underwater casting are high. It must be completely dense and properly constructed so that foam and sludge can flow out of the form. One difficulty is that the divers sometimes need to build parts of the form under the water. The work practice is challenging as it's complicated and done blindly. The used method is to pump concrete under the water surface through a concrete pipe with an underwater valve. During the casting process, the mouth of the pipe must always be below the concrete surface and the casting tube should be kept vertically. Finally, it is worth mentioning that the literature available today about underwater casting is inadequate, which makes it difficult to learn about the subject. The suggested solutions presented in the report are that all concrete coming to the construction site should be tested, even though it is not always a requirement. Thus, the decision of whether the concrete had a high enough quality for casting would be made for each delivery. In order to increase the chances of the concrete having desired properties, it is important that the truck delivering concrete to the construction site is clean and does not contain residues of a different concrete. Throughout the work, a good communication between pump operator, diver and management is needed to jointly solve problems. At last, it is recommended to help each other and take advantage of the expertise and experience within the company.

When subjected to a combination of moment and shear force, a reinforced concrete (RC) beam with either little or no transverse reinforcement can fail in shear before reaching its full flexural strength. This type of failure is sudden in nature and usually disastrous because it does not give sufficient warning prior to collapse. To prevent this type of shear failure, reinforced concrete beams are traditionally reinforced with stirrups. However, the use of stirrups is not always cost effective since it increases labor costs, and can make casting concrete difficult in situations where closely-spaced stirrups are required. The use of steel fiber reinforced concrete (SFRC) could be considered as a potential alternative to the use of traditional shear reinforcement. Concrete is very weak and brittle in tension, SFRC transforms this behaviour and improves the diagonal tension capacity of concrete and thus can result in significant enhancements in shear capacity. However, one of the drawbacks associated with SFRC is that the addition of fibers to a regular concrete mix can cause problems in workability. The use of self-consolidating concrete (SCC) is an innovative solution to this problem and can result in improved workability when fibers are added to the mix. The thesis presents the experimental results from tests on twelve slender self-consolidating fiber reinforced concrete (SCFRC) beams tested under four-point loading. The results demonstrate the combined use of SCC and steel fibers can improve the shear resistance of reinforced concrete beams, enhance crack control and can promote flexural ductility. Despite extensive research, there is a lack of accurate and reliable design guidelines for the use of SFRC in beams. This study presents a rational model which can accurately predict the shear resistance of steel fiber reinforced concrete beams. The thesis also proposes a safe and reliable equation which can be used for the shear design of SFRC beams.

When subjected to a combination of moment and shear force, a reinforced concrete (RC) beam with either little or no transverse reinforcement can fail in shear before reaching its full flexural strength. This type of failure is sudden in nature and usually disastrous because it does not give sufficient warning prior to collapse. To prevent this type of shear failure, reinforced concrete beams are traditionally reinforced with stirrups. However, the use of stirrups is not always cost effective since it increases labor costs, and can make casting concrete difficult in situations where closely-spaced stirrups are required. The use of steel fiber reinforced concrete (SFRC) could be considered as a potential alternative to the use of traditional shear reinforcement. Concrete is very weak and brittle in tension, SFRC transforms this behaviour and improves the diagonal tension capacity of concrete and thus can result in significant enhancements in shear capacity. However, one of the drawbacks associated with SFRC is that the addition of fibers to a regular concrete mix can cause problems in workability. The use of self-consolidating concrete (SCC) is an innovative solution to this problem and can result in improved workability when fibers are added to the mix. The thesis presents the experimental results from tests on twelve slender self-consolidating fiber reinforced concrete (SCFRC) beams tested under four-point loading. The results demonstrate the combined use of SCC and steel fibers can improve the shear resistance of reinforced concrete beams, enhance crack control and can promote flexural ductility. Despite extensive research, there is a lack of accurate and reliable design guidelines for the use of SFRC in beams. This study presents a rational model which can accurately predict the shear resistance of steel fiber reinforced concrete beams. The thesis also proposes a safe and reliable equation which can be used for the shear design of SFRC beams.

When subjected to a combination of moment and shear force, a reinforced concrete (RC) beam with either little or no transverse reinforcement can fail in shear before reaching its full flexural strength. This type of failure is sudden in nature and usually disastrous because it does not give sufficient warning prior to collapse. To prevent this type of shear failure, reinforced concrete beams are traditionally reinforced with stirrups. However, the use of stirrups is not always cost effective since it increases labor costs, and can make casting concrete difficult in situations where closely-spaced stirrups are required. The use of steel fiber reinforced concrete (SFRC) could be considered as a potential alternative to the use of traditional shear reinforcement. Concrete is very weak and brittle in tension, SFRC transforms this behaviour and improves the diagonal tension capacity of concrete and thus can result in significant enhancements in shear capacity. However, one of the drawbacks associated with SFRC is that the addition of fibers to a regular concrete mix can cause problems in workability. The use of self-consolidating concrete (SCC) is an innovative solution to this problem and can result in improved workability when fibers are added to the mix. The thesis presents the experimental results from tests on twelve slender self-consolidating fiber reinforced concrete (SCFRC) beams tested under four-point loading. The results demonstrate the combined use of SCC and steel fibers can improve the shear resistance of reinforced concrete beams, enhance crack control and can promote flexural ductility. Despite extensive research, there is a lack of accurate and reliable design guidelines for the use of SFRC in beams. This study presents a rational model which can accurately predict the shear resistance of steel fiber reinforced concrete beams. The thesis also proposes a safe and reliable equation which can be used for the shear design of SFRC beams.