Spelling suggestions: "subject:"static anda dynamic."" "subject:"static ando dynamic.""
11 |
Improved estimation of pore connectivity and permeability in deepwater carbonates with the construction of multi-layer static and dynamic petrophysical modelsFerreira, Elton Luiz Diniz 09 October 2014 (has links)
A new method is presented here for petrophysical interpretation of heterogeneous carbonates using well logs and core data. Developing this new method was necessary because conventional evaluation methods tend to yield inaccurate predictions of pore connectivity and permeability in the studied field. Difficulties in the petrophysical evaluation of this field are related to shoulder-bed effects, presence of non-connected porosity, rock layers that are thinner than the vertical resolution of well-logging tools, and the effect of oil-base mud (OBM) invasion in the measurements. These problems give rise to uncommon measurements and rock properties, such as: (a) reservoir units contained within thinly bedded and laminated sequences, (b) very high apparent resistivity readings in the oil-bearing zone, (c) separation of apparent resistivity logs with different depths of investigation, (d) complex unimodal and bimodal transverse relaxation distributions of nuclear magnetic resonance (NMR) measurements, (e) reservoir units having total porosity of 0.02 to 0.26 and permeability between 0.001mD to 4.2D, (f) significant differences between total and sonic porosity, and (g) low and constant gamma-ray values. The interpretation method introduced in this thesis is based on the detection of layer boundaries and rock types from high-resolution well logs and on the estimation of layer-by-layer properties using numerical simulation of resistivity, nuclear, and NMR logs. Layer properties were iteratively adjusted until the available well logs were reproduced by numerical simulations. This method honors the reservoir geology and physics of the measurements while adjusting the layer properties; it reduces shoulder-bed effects on well logs, especially across thinly bedded and laminated sequences, thereby yielding improved estimates of interconnected porosity and permeability in rocks that have null mobile water saturation and that were invaded with OBM. Additionally, dynamic simulations of OBM invasion in free-water depth intervals were necessary to estimate permeability. It is found that NMR transverse relaxation measurements are effective for determining rock and fluid properties but are unreliable in the accurate calculation of porosity and permeability in thinly bedded and highly laminated depth sections. In addition, this thesis shows that low resistivity values are associated with the presence of microporosity, and high resistivity values are associated with the presence of interconnected and vuggy porosity. In some layers, a fraction of the vuggy porosity is associated with isolated pores, which does not contribute to fluid flow. An integrated evaluation using multiple measurements, including sonic logs, is therefore necessary to detect isolated porosity. After the correction and simulation, results show, on average, a 34% improvement between estimated and core-measured permeability. Closer agreement was not possible because of limitations in tool resolution and difficulty in obtaining a precise depth match between core and well-log measurements. / text
|
12 |
The effect of applied and magnetic fields on the crystallisation of hydrocarbonsRodericks, Michele Melanie January 2003 (has links)
This thesis provides a background on the effects of applied and magnetic fields on crystallisation, and summarises the analytical techniques employed for characterisation and analysis. The study of applied fields was carried out on the crystallisation of one main system-solid nonadecane. This was then studied further to establish the effects of a solvent and a mixed solid system on the crystallisation of nonadecane. The systems studied were the crystallisations of: static and dynamic nonadecane, static and dynamic nonadecane in heptane, static and dynamic nonadecane and heneicosane, static and dynamic nonadecane and heneicosane in heptane and static and dynamic nonadecane and crude oil. The results of these studies showed that the magnetic and applied fields can affect electrostatic forces in molecular solids. It also showed that even the weakest of these forces, Van der Waals forces are affected by applied and magnetic fields.
|
13 |
Akutní vliv statického a dynamického strečinku na výskok / Acute effect of static and dynamic stretching on vertical jumpDostálová, Anna January 2017 (has links)
Title Acute effect of static and dynamic stretching on vertical jump. Objectives The aim of this thesis is to assess whether it is better to warm up by static or dynamic stretching in order to improve performance in the vertical jump. Methods The first part of this thesis is theoretical and is the basis for measurement, which is described in the second part. The tested set consists of ten women volleyball players. Each player underwent three vertical jump measurements on power plates Kistler, which recorded flight time of the player over the plates. All measurements were evaluated afterwards. Five attempts were recorded in each measurement. Measurements were carried out without stretching, after dynamic stretching and after static stretching. The thesis includes a survey that monitors the perception of the players` performance. Results Results of the total tested set measurement show that inclusion of dynamic stretching during the warm up leads to a slight decline in the physical performance. This decrease presents about 0.92%. Another conclusion of this research is that the inclusion of static stretching to the warm up also results in a slight decrease in the athletic performance. In this case the decrease is about 1.72%. In a direct comparison of these two types of stretching, the inclusion of...
|
14 |
Static or Dynamic Efficiency: Horizontal Merger Effects in the Wireless Telecommunications IndustryGrajek, M., Gugler, Klaus, Kretschmer, T., Miscisin, I. January 2019 (has links) (PDF)
This paper studies five mergers in the European wireless telecommunication industry and analyzes their impact on prices and capital expenditures of both merging carriers and their rivals. We find substantial heterogeneity in the relationship between increases in concentration and carriers' prices. The specifics of each merger case clearly matter. Moreover, we find a positive correlation between the price and the investment effect; when the prices after a merger increase (decrease), the investments increase (decrease) too. Thus, we document a trade-off between static and dynamic efficiency of mergers.
|
15 |
Contribution to the local approach of fracture in solid dynamics.Zhu, Yongyi 18 December 1992 (has links)
This study aims at the description, modelling and numerical prediction of ductile fracture in inelastic solids undergoing thermomechanical static or dynamic loading. Several research areas of contemporary interest in computer analysis of solids and structures are covered. The theoretical methodologies, computer implementations and practical applications will be treated.
This thesis summarizes my recent research works since 1989 at the MSM Department of the University of Liège. However, it should also be useful to those who are interested in the most recent developments in finite element methods and in applying these techniques to the analysis of real industrial problems. Numerous references to original sources are included.
For the convenience of the reader, each chapter of the thesis is designed to be self-contained, starts with a summary of the topic addressed, and finishes with an outline of the main results presented. Numerical examples are organized at the end of chapter 2 to 8 to assess the performance and applicability of the proposed mechanical and finite element models developed in each of them.
Hereafter, a brief overview of the thesis is given. After a brief introduction in chapter 1, the numerical tools that are necessary to perform large strain thermomechanical static or dynamic analysis of solids are presented.
In chapter 2, a general strategy for nonlinear dynamic finite element formulation is presented, including explicit and implicit time integration schemes. A special emphasis is placed on the application of high-speed metalforming and frictional contact-impact problems.
Chapter 3 describes a strategy for solving problems involving transient thermal and thermomechanical analysis.
A class of unified and mixed solid, thermal and coupled thermomechanical finite elements by assumed strain method is developed in chapter 4. Special care is taken to hourglass ans locking control. Once these developments are validated and their efficiency tested, it is then possible to tackle the problem of ductile fracture prediction and propagation.
In chapter 5, a bibliographic research on the "local approach of ductile fracture" is presented. The implementation of six fracture criteria into various constitutive laws for predicting fracture initiation sites is also shown.
A fully coupled elasto(-visco)-plastic damage model for isotropic material is developed in chapter 6. This model is based on irreversible thermodynamics theory and on the energy equivalence hypothesis.
Chapter 7 presents the theoretical and experimental comparison for isotropic ductile material at fracture.
Finally in chapter 8, the isotropic damage model of chapter 6 is extended to the case of anisotropic solids in which the damage growth itself is also anisotropic.
The above developments have been implemented to an existing finite element code LAGAMINE developed since 1982 at the MSM Department of the University of Liège and are applied to many real engineering problems such as high speed rolling, magnetoforming, impact upsetting, dynamic forging, deep drawing of axisymmetric ans square cups, hot upsetting, warm folding of 3D sheet, non-isothermal hemispherical punch stretching, and other contact-impact examples.
|
16 |
Comparison Of The 2d And 3d Analyses Methods For CfrdsOzel, Halil Firat 01 September 2012 (has links) (PDF)
The purpose is to compare the 2D and 3D analysis methodologies in investigating the performance of a Concrete Faced Rockfill Dam (CFRD) under static and dynamic loading conditions. Ç / okal Dam is the case study which is a CFRD
located in northwest Turkey at the Thracian Peninsula. Rockfill interface and faceplate were simulated as nonlinear modulus of elasticity, detailed nonlinear tractive behavior and total strain rotating crack model, respectively. These
behaviors were calibrated to define the exact behavior by detailed material tests. The analyses that cannot be done by 2D analyses, such as stress, crack width distribution along the face slab are conducted by 3D analyses to determine the necessity of these outcomes. Since effect of valley ends cannot be produced by 2D analyses, it is necessary to check 3D analyses to ensure liability of the results. Another comparison between detailed analysis of 2D models and linear elastic 2D models were covered to get practical and industrial solutions for the guiding methods of CFRDs for preliminary designs in this study.
|
17 |
Measurements Versus Predictions for the Static and Dynamic Characteristics of a Four-pad Rocker-pivot, Tilting-pad Journal BearingTschoepe, David 1987- 14 March 2013 (has links)
Measured and predicted static and dynamic characteristics are provided for a four-pad, rocker-pivot, tilting-pad journal bearing in the load-on-pad and load-between-pad orientations. The bearing has the following characteristics: 4 pads, .57 pad pivot offset, 0.6 L/D ratio, 60.33 mm (2.375in) pad axial length, 0.08255 mm (0.00325 in) radial clearance in the load-on-pad orientation, and 0.1189 mm (0.00468 in) radial clearance in the load-between-pad orientation. Tests were conducted on a floating test bearing design with unit loads ranging from 0 to 2903 kPa (421.1 psi) and speeds from 6.8 to 13.2 krpm.
For all rotor speeds, hot-clearance measurements were taken to show the reduction in bearing clearance due to thermal expansion of the shaft and pads during testing. As the testing conditions get hotter, the rotor, pads, and bearing expand, decreasing radial bearing clearance. Hot-clearance measurements showed a 16-25% decrease in clearance compared to a clearance measurement at room temperature.
For all test conditions, dynamic tests were performed over a range of excitation frequencies to obtain complex dynamic stiffness coefficients as a function of frequency. The direct real dynamic stiffness coefficients were then fitted with a quadratic function with respect to frequency. From the curve fit, the frequency dependence was captured by including a virtual-mass matrix [M] to produce a frequency independent [K][C][M] model.
The direct dynamic stiffness coefficients for the load-on-pad orientation showed significant orthotropy, while the load-between-pad did not. The load-between-pad showed slight orthotropy as load increased. Experimental cross-coupled stiffness coefficients were measured in both load orientations, but were of the same sign and significantly less than direct stiffness coefficients.
In both orientations the imaginary part of the measured dynamic stiffness increased linearly with increasing frequency, allowing for frequency independent direct damping coefficients.
Rotordynamic coefficients presented were compared to predictions from two different Reynolds-based models. Both models showed the importance of taking into account pivot flexibility and different pad geometries (due to the reduction in bearing clearance during testing) in predicting rotordynamic coefficients. If either of these two inputs were incorrect, then predictions for the bearings impedance coefficients were very inaccurate. The main difference between prediction codes is that one of the codes incorporates pad flexibility in predicting the impedance coefficients for a tilting-pad journal bearing.
To look at the effects that pad flexibility has on predicting the impedance coefficients, a series of predictions were created by changing the magnitude of the pad's bending stiffness. Increasing the bending stiffness used in predictions by a factor of 10 typically caused a 3-11% increase in predicted Kxx and Kyy, and a 10-24% increase in predicted Cxx and Cyy. In all cases, increasing the calculated bending stiffness from ten to a hundred times the calculated value caused slight if any change in Kxx, Kyy, Cxx, and Cyy. For a flexible pad an increase in bending stiffness can have a large effect on predictions; however, for a more rigid pad an increase in pad bending stiffness will have a much lesser effect.
Results showed that the pad's structural bending stiffness can be an important factor in predicting impedance coefficients. Even though the pads tested in this thesis are extremely stiff, changes are still seen in predictions when the magnitude of the pad?s bending stiffness is increased, especially in Cxx, and Cyy. The code without pad flexibility predicted Kxx and Kyy much more accurately than the code with pad flexibility. The code with pad flexibility predicts Cxx more accurately, while the code without pad flexibility predicted Cyy more accurately. Regardless of prediction Code used, the Kxx and Kyy were over-predicted at low loads, but predicted more accurately as load increased. Cxx, and Cyy were modeled very well in the load-on-pad orientation, while slightly overpredicted in the load-between-pad orientation. For solid pads, like the ones tested here, both codes do a decent job at predicting impedance coefficients
|
18 |
Traffic Assignment In Transforming Networks Case Study: AnkaraZorlu, Fikret 01 February 2006 (has links) (PDF)
This study investigates the relevance of dynamic traffic assignment models under uncertainty. In the last years researchers have dealt with advanced traffic control systems since road provision is not regarded as a proper solution to relieve congestion. Dynamic assignment which is an essential component of investment planning is regarded as a new research area in the field of urban transportation. In this study the performance of dynamic traffic assignment method, which incorporates time dependent flow, is compared with that of static model. Research outcomes showed that dynamic assignment method provides more reliable outcomes in predicting traffic flow / therefore its solution algorithm is integrated to conventional four staged model. Literature survey showed that researches have hot provided an appropriate framework for transforming networks. This study investigates travel demand variations in a dynamic city and discuses possible strategies to respond dynamic and uncertain properties of individuals&rsquo / travel behavior. Research findings showed that both external and internal uncertainties have significant influences on reliability of the model. Recommended procedure aims reducing uncertainty in order to improve reliability of model. Finally, the relevancy of the problem and the applicability of recently developed methods are discussed in Ankara case.
|
19 |
Contact damage of ceramics and ceramic nanocompositesWade, James January 2017 (has links)
Herein, we study the contact damage performance of two armour ceramics, alumina and silicon carbide, with varying microstructures and one particle-reinforced ceramic nanocomposite, alumina/silicon carbide, in an attempt to understand the microstructural mechanisms that affect plasticity and cracking under quasi-static and dynamic conditions. Quasi-static contact damage was imitated using Vickers indentation over a varying load regime. Numerical analysis of the indentation size effect, performed using the proportional specimen resistance model, allowed the contributions of plastic deformation and cracking to be separated into two individual values. In all three samples, higher levels of surface energy were found to correlate with increased amounts of cracking per unit area of indentation impression. Analytical modelling of crack initiation during Vickers indentation together with quantitative measurements of surface flaw populations revealed that such an increase in cracking damage was the result of higher densities of larger flaws. The hardness of the monolithic ceramics was found vary based on grain size and porosity levels, a smaller average grain size and lower porosity levels resulting in higher hardness values. In the nanocomposite materials, hardening was found to occur with further additions of silicon carbide nanoparticles. Such an effect has been attributed to the increased dislocation densities, as measured using Cr3+/Al2O3 fluorescence spectroscopy, and the impedance of dislocation movement within the lattice due to the presence of silicon carbide nanoparticles. In order to simulate dynamic contact damage, a low velocity, scaled-down drop-weight test was designed and developed. The dynamic contact damage resistance was determined based on the depth of penetration of a blunt indenter. In the monolithic ceramics, the indenter penetration was found to be shallower in materials of higher hardness. However, the nanocomposite materials displayed an opposing trend, the indenter penetration becoming deeper in the samples of higher hardness. The macro-scale fracture patterns produced during drop-weight impacts were seen to vary based on flaw populations and indenter penetration. In certain microstructures, extensive micro-cracking was also observed.
|
20 |
Strong-DISM: A First Attempt to a Dynamically Typed Assembly Language (D-TAL)Hernandez, Ivory 03 November 2017 (has links)
Dynamically Typed Assembly Language (D-TAL) is not only a lightweight and effective solution to the gap generated by the drop in security produced by the translation of high-level language instructions to low-level language instructions, but it considerably eases up the burden generated by the level of complexity required to implement typed assembly languages statically. Although there are tradeoffs between the static and dynamic approaches, focusing on a dynamic approach leads to simpler, easier to reason about, and more feasible ways to understand deployment of types over monomorphically-typed or untyped intermediate languages. On this occasion, DISM, a simple but powerful and mature untyped assembly language, is extended by the addition of type annotations (on memory and registers) to produce an instance of D-TAL. Strong-DISM, the resulting language, statically, lends itself to simpler analysis about type access and security as the correlation between datatypes and instructions with their respective memory and registers becomes simpler to observe; while dynamically, it disallows operations and further eliminates conditions that from high level languages could be used to violate/circumvent security.
|
Page generated in 0.0634 seconds