Caribbean-style hybrid concrete-masonry structures consist of a reinforced concrete frame with partially grouted and reinforced infill masonry walls. The infill walls are typically connected to the RC frame with cast-in-place dowel reinforcement along one or more edges of the wall. There is limited guidance in masonry codes to design these types of structures, and their seismic performance has not been characterized with experimental tests. In this work, an experimental program characterized the seismic behavior of hybrid concrete-masonry frames and showed they do not exhibit the typical strut mechanism observed in unreinforced masonry infill structures. In addition, a detailed finite element modeling scheme and calibration methodology was developed for modeling partially grouted masonry. This model includes a novel calibration method to account for the difference in the shear and tensile behavior of bed joints with grouted and ungrouted cells, and a method to account for the contribution of vertical reinforcement to the shear capacity of the bed joints with grouted cells. Finally, simplified models were proposed for use in engineering design. A modification of the TMS 402 strut model for hybrid concrete-masonry was suggested to incorporate the effects of the masonry infill and connections in large models.

Devido à sua alta taxa de mortalidade as doenças cardiovasculares vem sendo foco de pesquisas nos últimos anos. Estima-se que neste grupo, 42% das mortes foram consequência de doença coronariana (CHD) em 2012. Para auxiliar o acompanhamento de pacientes com CHD, este estudo teve como objetivo investigar um método simples e robusto que segmenta de maneira semi-automática a área da neoíntima em Tomografias Intravasculares por Coerência Óptica no Domínio da Frequência (FD-IOCT), a mais recente técnica de imagear vasos internamente. O método foi dividido em duas etapas. A primeira segmenta a área contida pelo lúmen através de operações morfológicas com valores de intensidade e aplicação da limiarização Otsu. Na segunda, o foco foi segmentar a área contida por partes de stent onde duas estratégias foram desenvolvidas e comparadas. Ambas as etapas (segmentação de área de lúmen e de stent) obtiveram resultados acurados com aproximadamente 98% de Verdadeiro Positivo, enquanto o Falso Positivo foi próximo de 3% para o lúmen e 5% para stent, onde uma das estratégias (para delimitar a área contida por stent) apresentou um tempo de execução 50 vezes maior que a outra. O método foi utilizado em 443 imagens com diferentes características e os resultados são encorajadores. / Due to its high mortality rate cardiovascular diseases have been the focus of research in recent years. It is estimated that among these, 42% of deaths were due to coronary heart disease (CHD) in 2012. To monitor patients with CHD, the goal of this study was to investigate a simple and robust method that segments semi-automatically the neointimal area on Frequency Domain Intravascular Optical Coherence Tomography (FD-IOCT), the latest technology to view vessels internally. The method was divided into two steps. The first one segments the area contained by the lumen through morphological operations on intensity values and the Otsu threshold. In the second one, the focus was to segment the area contained by stent struts where two strategies were developed and compared. Both steps (lumen and stent strut area segmentation) obtained accurate results with true positives approximately 98%, while the false positives were close to 3% for the lumen and 5% for the stent, where one strategy (to delimit the area contained by stent struts) showed run time of 50 times the other. The method was executed on 443 images with different characteristics and the results are encouraging.

O modelo de bielas e tirantes apresenta como uma de suas vantagens a generalidade, ou seja, é capaz de representar, de modo aproximado, porém realista e sistemático, grande parte dos elementos de concreto estrutural da atualidade. Além disso, permite ao engenheiro fácil visualização físico-intuitiva do comportamento do concreto estrutural. Por outro lado, o modelo ainda tem um enorme potencial não aproveitado. Ainda não se tem um critério exato para determinação dos nós e das seções transversais das bielas de alguns elementos. Apesar de haver certas incertezas no caso de vigas-parede e principalmente de blocos de fundação, nas vigas esses elementos do modelo podem ser determinados sem grandes dificuldades. Possivelmente, a solução seria variar as dimensões das bielas e as posições dos nós, ambas hipotéticas, a fim de confrontar várias situações com resultados experimentais. Daí a grande importância da difusão do modelo de bielas e tirantes: um maior número de análises de modelagens e de resultados de ensaios levará a um maior domínio sobre o modelo. Este trabalho consiste na análise de vigas de concreto armado utilizando modelos de bielas e tirantes. São apresentados os conceitos que levaram à concepção do modelo, desde a Analogia Clássica da Treliça, chegando aos critérios para verificação dos elementos da treliça e às recomendações atuais de normas e pesquisadores. Com o auxílio do programa computacional CAST (2000), foram modeladas quatro vigas, sendo as três primeiras biapoiadas sem descontinuidades e a quarta com balanço e descontinuidade geométrica (abertura na alma). A primeira viga biapoiada teve algumas de suas características iniciais alteradas a fim de gerar o segundo e o terceiro modelos, procurando-se estabelecer limites de carregamentos e análises comparativas. Os resultados das modelagens permitiram comparações com os resultados das verificações realizadas segundo os critérios da NBR 6118:2003 e do MC CEB-FIP (1990) e, permitiram também, identificar os aspectos de maior dificuldade na concepção de um modelo de bielas e tirantes e os pontos críticos dos mesmos, nos quais há maior possibilidade de falha nas verificações / One of the main advantages presented by the strut-and-tie model is generality. This model is able to approximately represent, in a realistic and systematic way, the majority of today’s reinforced concrete elements. Furthermore, it allows the physics-intuitive visualization of the behavior presented by structural concrete. On the other hand, its potentials are not fully explored yet. Up to date, there is no accurate criterion for the determination of nodes and transverse sections of some strut elements. Despite presenting some uncertainties related to the determination of wall-beams (and mainly of foundation blocks), the model can determine beams without major difficulties. Probably, the key is to vary the dimensions of the struts and the positions of the nodes, both hypothetical, in order to confront various situations with experimental data. Hence, it is very important to diffuse the strut-and-tie model: the bigger the number of modeling analysis and experimental data, the better the comprehension of the model. This work aims to analyze reinforced concrete beams employing the strut-and-tie model. Here are presented the concepts that led to the development of the model, ranging from the Truss Classic Analogy to the criteria employed to verify truss elements and the recommendations from researchers and established standards (rules or norms). Four examples of beams were modeled. Three of them were double-based and the fourth presented balance and no geometric discontinuity (with an opening). Some of the characteristics of the first double-based beam were altered in order to generate the second and the third model, thus establishing loading limits and comparative analysis. The modeling allowed comparisons between the verifications performed in accordance with the NBR 6118:2003 and MC CEB-FIP criteria. It also allowed the identification of major difficulties and critical aspects related to the development of struts and ties, the ones that are most prone to failure in the verification process

Este trabalho estuda o comportamento estrutural de blocos sobre estacas em concreto armado situados em divisas de terrenos. Foi feita revisão bibliográfica abordando os assuntos de blocos de coroamento, vigas de equilíbrio, modelo de bielas e tirantes e um breve comentário sobre o programa computacional Diana (2010). O trabalho apresenta um roteiro para análise estrutural e dimensionamento de vigas de equilíbrio sobre estacas com pilar excêntrico ao apoio. É apresentado um exemplo feito por Andrade (1989), comparado com o método proposto por Burke (1979) e com análise numérica. Além deste, foram analisados casos de projetos reais utilizando o método Burke (1979) adaptado neste trabalho. Alguns desses exemplos foram modelados em regime elástico e linear no programa computacional Diana (2010). São apresentadas comparações de resultados obtidos com o método Burke (1979) e análise numérica, comprovando a eficácia desse método. Em todos os exemplos estudados o método proposto por Burke (1979) indicou bons resultados quando comparados com os encontrados em análise computacional. A dissertação apresenta soluções para projetos de bloco sobre estacas, situados em divisas de terrenos e associados a vigas de equilíbrio. / This research investigates the structural behavior of reinforced concrete blocks piles located on the limit of land. Literature review was done about blocks piles, balance beams, strut and tie model and a short comment about the Diana computer program (2010). The dissertation presents a roadmap for structural analysis and sizing of balance beams on stakes with eccentric support pillar. An example, which was studied by Andrade (1989), is compared with the same example done using the method proposed by Burke (1979) and with numerical analysis. In addition to this, are analyzed real cases of projects using the method of Burke (1979). Some of these examples were modeled in linear and elastic characteristics using Diana program computer (2010). Here, it is presented comparisons between the method proposed by Burke (1979) and numerical analysis. It is presented comparisons between the method Burke (1979) and numerical analysis, proving the effectiveness of this method. In all examples studied the method proposed by Burke (1979) provided with good accuracy the results for computer analysis. The conclusion presents suggestions for projects of block piles located in limit of land associated with balance beams.

Este trabalho estuda o comportamento de blocos rígidos de concreto armado sobre uma, duas, três, quatro e cinco estacas, submetidos à ação de força centrada. Com o objetivo de contribuir para critérios de projeto, utilizaram-se resultados obtidos por meio de modelos analíticos e realizou-se análise numérica utilizando-se programa baseado no método dos elementos finitos. Foi desenvolvida, ainda, uma análise comparativa entre os processos de dimensionamento adotados em projeto, na qual se verificou grande variabilidade dos resultados. Para análise numérica adotou-se comportamento do material como elástico linear e os resultados de interesse foram os fluxos de tensões em suas direções principais. Nos modelos adotados variaram-se os diâmetros de estacas e dimensões de pilar, a fim de se verificar as diferenças na formação dos campos e trajetórias de tensões. Concluiu-se que o modelo de treliça utilizado em projetos é simplificado e foram feitas algumas sugestões para a utilização de um modelo de bielas e tirantes mais refinado. Foi possível a verificação da influência da variação da geometria de estacas e de pilares no projeto de blocos sobre e a revisão dos critérios para os arranjos das armaduras principais. Para os modelos de blocos sobre cinco estacas adotados concluiu-se que o comportamento não é exatamente como considerado na prática / This work describes the behavior of rigid reinforced concrete pile-caps with one, two, three, four and five piles subjected to patches of loading on the center top surfaces of the column. Programs based on finite elements method were used to obtain numerical results and results obtained by means of analytic models were used. A comparative analysis was developed among the processes adopted in design, which large variability of the results was verified. An elastic linear behavior of the material was adopted for numerical analysis and interest results were stress paths along main directions. Piles diameters and column dimensions of the models were been varied, in order to verify the differences in the formation of the regions and trajectories of stress. It is ended that used the truss model is simplified. Some suggestions were made for the use of a more refined strut-and-tie model than the one used in design and it was possible the verification of the variation geometry of piles and columns influence. It was still made a revision of the reinforcement layouts. The conclusion for adopted five-pile-caps was that the behavior is not exactly as considered in the practice

O projeto estrutural deve considerar as incertezas provenientes das variáveis envolvidas no dimensionamento dos elementos estruturais, tais como propriedades dos materiais, dimensões dos elementos estruturais e intensidade dos carregamentos atuantes. Existe também a variabilidade inerente aos métodos de análise estrutural, originária de imprecisões na idealização da distribuição das tensões e deformações dos elementos estruturais. Sendo assim, esta dissertação visa analisar a variabilidade dos desvios dos modelos de cálculo propostos por Blevot e Frémy (1967), Fusco (1994) e Santos (2013), todos baseados no método das bielas e tirantes, para blocos sobre duas, três e quatro estacas submetidos a carregamento centrado. Estes elementos estruturais possuem significativa importância, visto que atuam na transmissão dos esforços provenientes dos pilares às fundações profundas. Os modelos de cálculo foram confrontados entre si e com resultados experimentais de Blevot e Frémy (1967), Mautoni (1971), Clarke (1973), Miguel (2000) e Suzuki et al. (1998 / 1999 / 2000 / 2001) para determinação dos parâmetros estatísticos dos desvios desses modelos em relação aos ensaios. Os resultados apontaram desempenho satisfatório para os três modelos de cálculo. Em geral, todos os métodos se mostraram favoráveis à segurança nos casos avaliados para os três tipos de blocos de fundação. / Structural design must consider the uncertainties coming from the variables involved in dimensioning of the structural elements, such as material properties, dimensions of structural elements, and intensity of active loads. There is also inherent variability in structural analysis methods, originated from imprecision in idealization of the distribution of tensions and deformations of structural elements. Thus, this dissertation aims to analyze the variability of calculation models deviations proposed by Blevot and Frémy (1967), Fusco (1994) and Santos (2013), all based on strut and tie method, for two, three and four pile caps submitted to center load. These structural elements are of significant importance, since they act in transmission of loads from columns to deep foundations. Calculation models were compared with each other and with experimental results from Blevot and Frémy (1967), Mautoni (1971), Clarke (1973), Miguel (2000) and Suzuki et al. (1998 / 1999 / 2000 / 2001) to determine the statistical parameters of these model deviations in relation to the tests. Results indicated satisfactory performance for the three calculation models. In general, all methods were favorable to safety in cases evaluated for the three pile caps types.

Corrosion of reinforcing steel is a major problem facing infrastructures owners with billions of dollars spent in repairing our aging infrastructure. One of the first steps in the repair process is to quantify the strength degradation in a reinforced concrete element caused by the corrosion of reinforcing steel. An understanding of the forces involved in the load carrying mechanisms is imperative; the transfer of shear forces in reinforced concrete beams is one of these load carrying mechanisms. The shear transfer mechanism is different near the end of beams, adjacent to point loads, and near changes in cross section. These regions are known as disturbed regions. Structural engineers have a good understanding of the shear transfer mechanism in disturbed regions. However, the effects of corroded shear reinforcement in these regions have not been widely investigated. The current study is comprised of an experimental program and analytical strut and tie modeling aimed at quantifying the strength reduction that occurs in disturbed regions of reinforced concrete beams with corroded shear reinforcement. The feasibility of strengthening a beam with dry lay-up carbon fibre reinforced polymer (CFRP) to repair the damage caused by corrosion of the shear reinforcement was also investigated. In the experimental study, a total of 16 reinforced concrete beams were cast. The specimens were 350 mm deep, 125 mm wide and 1850 mm long. Three shear-span to depth ratios (1.0, 1.5, 2.0) were selected. Each specimen was reinforced in flexure with two 25M bars and the shear reinforcement was 10M spaced at 150 mm on centre. The specimens were corroded for 21 days, 60 days, and 120 days corresponding to low, medium, and high corrosion levels. In addition, three specimens were constructed without shear reinforcement in the shear-span in order to compare the results from the corroded specimens. One specimen was also corroded to a high level and repaired with dry lay-up CFRP. The specimens were corroded using an accelerated corrosion technique. There was evidence of cracking of the cover concrete in all specimens, and in the more severely corroded specimens delamination of the cover concrete was recorded. The stiffness of the corroded specimens was less than their corresponding control specimen, and a strength reduction was evident in most specimens. The maximum recorded strength reduction was 52% compared to the companion uncorroded specimen. It was revealed that a more critical case occurs when the corroded shear reinforcement was shifted during placement or was inclined closer to the direction of the compressive force flow. Also, it was observed that the corroded shear reinforcement still provides limited ductility in comparison to the un-corroded reinforcement. A strut and tie model was developed based on the experiments to explain the behaviour of disturbed regions with corroded shear reinforcement. The model consisted of direct and indirect struts. The effects of corrosion were expressed in terms of a reduction in the stirrup cross-section, a reduction of compressive strength due to corrosion cracking, and a reduction in the concrete cross section width. It was hypothesized that the corrosion crack width influences the concrete compressive strength in the strut; consequently, a mathematical model was developed that related the reduction in concrete compressive strength with corrosion crack width. Also, a relationship between reinforcing steel mass loss and corrosion crack width was utilized from the published literature. An effective cross section width was obtained by reducing the width by the damaged concrete cover. The results from these models were input into a strut and tie model as a reduction in concrete compressive strength. The output from the strut and tie model was the ultimate shear strength of the specimen. The developed models were compared with a model from the literature and compared with the experimental results. The major contribution of this research is to allow designers to analyze disturbed regions with corroded shear reinforcement and determine the strength degradation; subsequently, one can determine what strengthening procedure would be most appropriate.

Corrosion of reinforcing steel is a major problem facing infrastructures owners with billions of dollars spent in repairing our aging infrastructure. One of the first steps in the repair process is to quantify the strength degradation in a reinforced concrete element caused by the corrosion of reinforcing steel. An understanding of the forces involved in the load carrying mechanisms is imperative; the transfer of shear forces in reinforced concrete beams is one of these load carrying mechanisms. The shear transfer mechanism is different near the end of beams, adjacent to point loads, and near changes in cross section. These regions are known as disturbed regions. Structural engineers have a good understanding of the shear transfer mechanism in disturbed regions. However, the effects of corroded shear reinforcement in these regions have not been widely investigated. The current study is comprised of an experimental program and analytical strut and tie modeling aimed at quantifying the strength reduction that occurs in disturbed regions of reinforced concrete beams with corroded shear reinforcement. The feasibility of strengthening a beam with dry lay-up carbon fibre reinforced polymer (CFRP) to repair the damage caused by corrosion of the shear reinforcement was also investigated. In the experimental study, a total of 16 reinforced concrete beams were cast. The specimens were 350 mm deep, 125 mm wide and 1850 mm long. Three shear-span to depth ratios (1.0, 1.5, 2.0) were selected. Each specimen was reinforced in flexure with two 25M bars and the shear reinforcement was 10M spaced at 150 mm on centre. The specimens were corroded for 21 days, 60 days, and 120 days corresponding to low, medium, and high corrosion levels. In addition, three specimens were constructed without shear reinforcement in the shear-span in order to compare the results from the corroded specimens. One specimen was also corroded to a high level and repaired with dry lay-up CFRP. The specimens were corroded using an accelerated corrosion technique. There was evidence of cracking of the cover concrete in all specimens, and in the more severely corroded specimens delamination of the cover concrete was recorded. The stiffness of the corroded specimens was less than their corresponding control specimen, and a strength reduction was evident in most specimens. The maximum recorded strength reduction was 52% compared to the companion uncorroded specimen. It was revealed that a more critical case occurs when the corroded shear reinforcement was shifted during placement or was inclined closer to the direction of the compressive force flow. Also, it was observed that the corroded shear reinforcement still provides limited ductility in comparison to the un-corroded reinforcement. A strut and tie model was developed based on the experiments to explain the behaviour of disturbed regions with corroded shear reinforcement. The model consisted of direct and indirect struts. The effects of corrosion were expressed in terms of a reduction in the stirrup cross-section, a reduction of compressive strength due to corrosion cracking, and a reduction in the concrete cross section width. It was hypothesized that the corrosion crack width influences the concrete compressive strength in the strut; consequently, a mathematical model was developed that related the reduction in concrete compressive strength with corrosion crack width. Also, a relationship between reinforcing steel mass loss and corrosion crack width was utilized from the published literature. An effective cross section width was obtained by reducing the width by the damaged concrete cover. The results from these models were input into a strut and tie model as a reduction in concrete compressive strength. The output from the strut and tie model was the ultimate shear strength of the specimen. The developed models were compared with a model from the literature and compared with the experimental results. The major contribution of this research is to allow designers to analyze disturbed regions with corroded shear reinforcement and determine the strength degradation; subsequently, one can determine what strengthening procedure would be most appropriate.

A compatibility-based strut-and-tie model C-STM is proposed for analyzing deep beams and disturbed regions with particular emphasis on reinforced concrete bridge piers. In addition to the normal strut-and-tie force equilibrium requirements the model accounts for non-linear behavior through displacement compatibility using inelastic constitutive laws of cracked reinforced concrete. The model is implemented into widely used commercial structural analysis software and validated against results from previously conducted large scale experiments. A near full-scale experiment on a reinforced concrete sub-assemblage that represents cantilevered and straddle pier bents is conducted to investigate the shear-flexure performance of deep (disturbed) regions. Insights into the development of nonlinear behavior and the final collapse failure mechanism are then evaluated and accurately modeled using the C-STM. It is concluded that the proposed C-STM serves as an advanced method of analysis that can predict with suitable accuracy the force-deformation response of both D- and B- regions, deep beams, and beam-columns. This provides engineers with a supplementary analysis tool that can be used to assess the nonlinear behavior of bridge piers with stocky members and/or large disturbed regions.

Strut-and-tie modeling (STM) is a versatile, lower-bound (i.e. conservative) design method for reinforced concrete structural components. Uncertainty expressed by engineers related to the implementation of existing STM code specifications as well as a growing inventory of distressed in-service bent caps exhibiting diagonal cracking was the impetus for the Texas Department of Transportation (TxDOT) to fund research project 0-5253, D-Region Strength and Serviceability Design, and the current implementation project (5-5253-01). As part of these projects, simple, accurate STM specifications were developed. This thesis acts as a guidebook for application of the proposed specifications and is intended to clarify any remaining uncertainties associated with strut-and-tie modeling. A series of five detailed design examples feature the application of the STM specifications. A brief overview of each design example is provided below. The examples are prefaced with a review of the theoretical background and fundamental design process of STM (Chapter 2). • Example 1: Five-Column Bent Cap of a Skewed Bridge - This design example serves as an introduction to the application of STM. Challenges are introduced by the bridge’s skew and complicated loading pattern. A clear procedure for defining relatively complex nodal geometries is presented. • Example 2: Cantilever Bent Cap - A strut-and-tie model is developed to represent the flow of forces around a frame corner subjected to closing loads. The design and detailing of a curved-bar node at the outside of the frame corner is described. • Example 3a: Inverted-T Straddle Bent Cap (Moment Frame) - An inverted-T straddle bent cap is modeled as a component within a moment frame. Bottom-chord (ledge) loading of the inverted-T necessitates the use of local STMs to model the flow of forces through the bent cap’s cross section. • Example 3b: Inverted-T Straddle Bent Cap (Simply Supported) - The inverted-T bent cap of Example 3a is designed as a member that is simply supported at the columns. • Example 4: Drilled-Shaft Footing - Three-dimensional STMs are developed to properly model the flow of forces through a deep drilled-shaft footing. Two unique load cases are considered to familiarize the designer with the development of such models. / text