Le renforcement des sols par géosynthétique est appliqué dans de nombreux types d’ouvrage : remblais sur sol compressible, talus sur fondations stables, remblais sur des cavités et ouvrages de soutènement. La stabilité de ces ouvrages dépend entre autres de l’efficacité des ancrages des nappes géosynthétiques. Les ancrages droit et avec retour sont les plus couramment utilisés. Afin d'améliorer les connaissances actuelles sur le comportement des systèmes d'ancrage, des études expérimentales et numériques ont été développées conjointement. Ce travail de thèse concerne dans une première partie, la modélisation physique tridimensionnelle du comportement des géosynthétiques pour deux types ancrages (ancrage droit et ancrage avec retour). Ces essais ont été réalisés dans une chambre d’étalonnage en conditions contrôlées et instrumentées en laboratoire. Dans une deuxième partie de cette thèse, les paramètres d’interaction sol/géosynthétique déduits à partir de l’étude expérimentale ont été implémentés dans le code de calcul numérique bidimensionnel en milieu continu FLAC2D pour une meilleure compréhension du comportement des géosynthétique en ancrage. L’influence de plusieurs paramètres sur le comportement du géosynthétique en ancrage avec et sans retour a été traitée dans cette étude numérique. Parallèlement à cette modélisation, une autre modélisation numérique (discontinue) par la méthode des éléments discrets (PFC2D) a été réalisée. Ces modélisations ont donné des résultats proches de ceux obtenus expérimentalement et confirme l'analyse faite au sujet des mécanismes d'ancrage. / The soil reinforcement by geosynthetic is used in many types of structures: embankments on compressible soil, slope on a stable foundation, embankments on cavities and retaining structures. The stability of these structures specially depends on the efficiency of the anchors holding the geosynthetic sheets. The simple run-out and anchorage with wrap around are most commonly used. In order to improve the available knowledge of the anchorage systems behaviour, experimental and numerical studies were developed jointly. This thesis work concerns in the first part a three-dimensional physical modelling of the behaviour of geosynthetics in two anchors (simple run-out and anchorge with wrap around). The pull-out tests were performed in a test tank under controlled conditions in the laboratory. In the second part, the parameters of the interaction soil/geosynthetic found from the experimental study were used into the numerical code “FLAC2D” (continuous) for a better understanding of the behaviour of geosynthetics in anchorage. The influence of several parameters on the behaviour of geosynthetic was treated in this numerical study. In parallel with this model, another numerical modelling (discontinuous) by the discrete element method (PFC2D) was carried out. The results of these models are closely to experimental results which confirm the analysis about the anchoring mechanisms.

The autogenous shrinkage due to self-desiccation of high- and ultra-high performance concretes with very low water-cement ratio in case of restraint leads to considerable stresses starting from very early age. The resultant risk of cracking presently cannot be adequately investigated. Parameters that are particularly difficult to capture experimentally are the concrete temperature and the viscoelasticity. The primary objective of this work was to assess as precise as possible the autogenous shrinkage cracking propensity of representative concretes at strong restraint and constant room temperature. Test methods needed to be chosen and enhanced in a way that preferably allowed for the efficient and precise investigation of all relevant factors in the future. Ideally, a method suitable for a complete empirical modeling was provided. First the methodological requirements and the advantages and disadvantages of existing test methods were discussed. Based on this, optimized test methods were proposed. Their suitability was verified using the example of ultra-high strength concrete. The choice of concrete compositions considered the essential measures for reducing shrinkage (internal curing, shrinkage-reducing admixtures, reduction of the fraction of Portland cement in the binder). The autogenous shrinkage was measured with the shrinkage cone method. This new test method was validated by investigations of the repeatability and reproducibility and proved efficient and precise. It allows for measurements under non-isothermal conditions; no established test method exists for that purpose to date. The autogenous shrinkage of the ultra-high strength concretes at the age of 24 h, investigated under quasi-isothermal conditions (20 °C), was between 0,25 mm/m and 0,70 mm/m. It was particularly low when a shrinkage-reducing admixture was added and when superabsorbent polymers were used. The stresses due to restraint were determined with the restrained ring test. A large part of the stresses to be expected according to Hooke’s Law were eliminated by creep and relaxation. The relaxation capacity being very pronounced at very early age was the main reason that no visible cracking occurred, not even with the concretes with high autogenous shrinkage. The development of the autogenous shrinkage cracking propensity was described as ratio of restraint stress and splitting tensile strength. By means of modified ring tests, used to determine the maximum tensile stress, it could be shown that the ratio of stress to strength is an appropriate failure criterion. However, the cracking propensity can be calculated correctly only if the strongly age-dependent ratio of uniaxial to splitting tensile strength is accounted for. Besides, it needs to be considered that at very early age a plastic stress redistribution may occur in restrained ring tests. The reference concrete showed a high cracking propensity of up to 0.68. The fact that shrinkage-reducing measures led to significantly lower values reveals their relevance for the safe application of ultra-high strength concrete. However, the investigations carried out here at 20 °C do not allow for a final assessment of the cracking propensity under typical on-site conditions. To empirically model the autogenous shrinkage cracking propensity as a function of temperature and stress level in the future, an analytical stress solution for non-isothermal restrained ring tests and a new approach for investigating the residual stress and relaxation capacity by means of non-passive restrained ring tests was suggested. / Das durch Selbstaustrocknung verursachte autogene Schwinden von besonders leistungsfähigen Betonen mit sehr niedrigem Wasserzementwert führt bei Dehnungsbehinderung bereits in sehr frühem Alter zu erheblichen Zwangsspannungen. Die Gefahr der Rissbildung, die sich daraus ergibt, lässt sich bislang nur unzureichend untersuchen. Experimentell besonders schwer zu erfassende Faktoren sind die Betontemperatur und die Viskoelastizität. Das vorrangige Ziel der Arbeit war die möglichst genaue Ermittlung der autogenen Schwindrissneigung repräsentativer Betone bei starker Dehnungsbehinderung und konstanter Raumtemperatur. Dabei waren die Prüfverfahren möglichst so zu wählen und weiterzuentwickeln, dass sich zukünftig alle relevanten Faktoren effizient und genau untersuchen lassen. Im Idealfall sollte eine Methode entstehen, die eine vollständige empirische Modellierung erlaubt. Zunächst wurden die methodischen Anforderungen und die Vor- und Nachteile existierender Prüfverfahren diskutiert. Darauf aufbauend wurden optimierte Verfahren vorgeschlagen. Ihre Eignung wurde an ultrahochfestem Beton überprüft. Bei der Auswahl der Betone wurden die wesentlichen Maßnahmen zur Schwindreduzierung berücksichtigt (innere Nachbehandlung, schwindreduzierende Zusatzmittel, Verringerung des Portlandzementanteils am Bindemittel). Das autogene Schwinden wurde mit dem Schwindkegelverfahren gemessen. Das neue Verfahren wurde durch Untersuchungen zur Wiederhol- und Vergleichsgenauigkeit validiert und erwies sich als effizient und genau. Es ermöglicht Messungen unter nicht-isothermen Bedingungen; hierfür existiert bisher kein etabliertes Verfahren. Das autogene Schwinden der untersuchten ultrahochfesten Betone unter quasi-isothermen Bedingungen (20 °C) betrug im Alter von 24 h zwischen 0,25 mm/m und 0,70 mm/m. Besonders gering war es bei Zugabe eines schwindreduzierenden Zusatzmittels bzw. Verwendung superabsorbierender Polymere. Mit dem Ring-Test wurden die bei Dehnungsbehinderung entstehenden Spannungen ermittelt. Ein großer Teil der gemäß Hooke’schem Gesetz zu erwartenden Spannungen wurde durch Kriechen und Relaxation abgebaut. Die im sehr frühen Alter stark ausgeprägte Relaxationsfähigkeit war der wesentliche Grund dafür, dass es selbst bei Betonen mit hohem autogenen Schwinden zu keiner erkennbaren Rissbildung kam. Die Entwicklung der autogenen Schwindrissneigung wurde als Verhältnis von Zwangsspannung und Spaltzugfestigkeit beschrieben. Durch modifizierte Ring-Tests, mit deren Hilfe die maximale Zugspannung ermittelt wurde, konnte gezeigt werden, dass das Verhältnis von Spannung und Festigkeit als Versagenskriterium geeignet ist. Die Rissneigung lässt sich aber nur dann korrekt berechnen, wenn das stark altersabhängige Verhältnis von einaxialer Zugfestigkeit und Spaltzugfestigkeit berücksichtigt wird. Außerdem ist zu beachten, dass es im sehr frühen Alter zu einer plastischen Spannungsumlagerung in Ring-Tests kommen kann. Der Referenzbeton wies eine hohe Rissneigung von bis zu 0,68 auf. Dass die schwindreduzierenden Maßnahmen zu deutlich geringeren Werten führten, zeigt deren Bedeutung für den sicheren Einsatz von ultrahochfestem Beton. Die hier bei 20 °C durchgeführten Untersuchungen erlauben allerdings keine abschließende Bewertung der Rissneigung unter baustellentypischen Bedingungen. Um die autogene Schwindrissneigung zukünftig als Funktion der Temperatur und des Lastniveaus empirisch modellieren zu können, wurden eine analytische Spannungslösung für nicht-isotherme Ring-Tests und ein neuer Ansatz zur Untersuchung der Resttrag- und Relaxationsfähigkeit mit Hilfe nicht-passiver Ring-Tests vorgeschlagen.

Este projeto tem o objetivo de apresentar o estudo dos arames da armadura de tração que são empregados no transporte de óleo, gás e umbilicais hidráulicos na indústria petrolífera. Este estudo foi desenvolvido sob a necessidade de melhor ancoragem dos arames da armadura de tração de modo a garantir que, mesmo após a ruptura do arame dentro do conector não haverá o escorregamento do mesmo provocando a queda do duto flexível. Assim sendo, foi estabelecido o estudo de aderência da interface dos arames da armadura de tração dos dutos flexíveis. Com os ensaios concluídos se estudou um novo procedimento para o melhoramento de aderência mecânica dos arames com a resina epóxi. Após os ensaios de aderência e adesão concluídos foi realizado ensaio de tração em cada arame da armadura de tração sob sua montagem no conector de extremidade para verificação de carregamento que chegam nos ganchos dos arames da armadura de tração. Os estudos realizados no conector de extremidade de 2,5 demonstram que os ganchos dos arames da armadura de tração são de grande importância para a integridade estrutural do duto flexível, visto que o cone de resina formado dentro do conector não está em contato com toda a área dos arames das armaduras de tração. / This project aims to present the study of tensile armor wires usually employed in the transport of oil, gas and hydraulic umbilicals in the petroleum industry. This study was developed as a need for better anchoring of the tensile armor wires in order to guarantee that even after the rupture of the wire within the connector it will not slip causing the fall of the flexible riser. Thus was established the adhesion study of the interface of the tensile armor wires of the flexible risers. After the end of the tests a new procedure for improving mechanical adhesion between the wires and the epoxy resin was studied. After the end of the adhesion tests tensile test was performed on each wire of the tensile armor under its mounting on the end fitting for checking the loading that reaches the hook of the armor wires. The trials performed in the 2.5end fitting show that the tensile armor wire hooks are of great importance for the structural integrity of the flexible riser, as there is no contact between the resin cone formed within the end fitting and the tensile armor wires area.

Este projeto tem o objetivo de apresentar o estudo dos arames da armadura de tração que são empregados no transporte de óleo, gás e umbilicais hidráulicos na indústria petrolífera. Este estudo foi desenvolvido sob a necessidade de melhor ancoragem dos arames da armadura de tração de modo a garantir que, mesmo após a ruptura do arame dentro do conector não haverá o escorregamento do mesmo provocando a queda do duto flexível. Assim sendo, foi estabelecido o estudo de aderência da interface dos arames da armadura de tração dos dutos flexíveis. Com os ensaios concluídos se estudou um novo procedimento para o melhoramento de aderência mecânica dos arames com a resina epóxi. Após os ensaios de aderência e adesão concluídos foi realizado ensaio de tração em cada arame da armadura de tração sob sua montagem no conector de extremidade para verificação de carregamento que chegam nos ganchos dos arames da armadura de tração. Os estudos realizados no conector de extremidade de 2,5 demonstram que os ganchos dos arames da armadura de tração são de grande importância para a integridade estrutural do duto flexível, visto que o cone de resina formado dentro do conector não está em contato com toda a área dos arames das armaduras de tração. / This project aims to present the study of tensile armor wires usually employed in the transport of oil, gas and hydraulic umbilicals in the petroleum industry. This study was developed as a need for better anchoring of the tensile armor wires in order to guarantee that even after the rupture of the wire within the connector it will not slip causing the fall of the flexible riser. Thus was established the adhesion study of the interface of the tensile armor wires of the flexible risers. After the end of the tests a new procedure for improving mechanical adhesion between the wires and the epoxy resin was studied. After the end of the adhesion tests tensile test was performed on each wire of the tensile armor under its mounting on the end fitting for checking the loading that reaches the hook of the armor wires. The trials performed in the 2.5end fitting show that the tensile armor wire hooks are of great importance for the structural integrity of the flexible riser, as there is no contact between the resin cone formed within the end fitting and the tensile armor wires area.

Neste trabalho foi feito o estudo sobre o efeito de elementos microligantes na composição química, microestrutura e propriedades mecânicas de metais como soldado produzidos por arco submerso com adição de pó de ferro em aço de alta resistência e baixa liga (ARBL). Foram feitos dois cordões de solda utilizando os aços BS - 4360 - 50 e USI - SAC - 50, o arame EM - 12K, o pó de ferro ESAB 400 e o fluxo experimental 10.71P. Utilizando-se a corrente de 600 A, tensão de 34 V, velocidade de soldagem de 30 cm/min e vazão de pó de ferro de 6,7 Kg/h foram produzidos os metais como soldado com um único passe e chanfro em \"V\", que mostraram características de boa temperabilidade e estrutura refinada. O microconstituinte em maior porcentagem nos dois cordões de solda foi a ferrita acicular. Os ensaios mecânicos realizados foram a dureza, tração e impacto. O cordão de solda com nióbio e vanádio obteve maiores valores de dureza e resistência à tração em relação ao cordão com cobre, cromo e níquel. Entretanto os altos teores de manganês presentes fizeram com que o endurecimento por solução sólida reduzisse significativamente a resistência ao impacto dos dois cordões de solda. A natureza das inclusões não metálicas foi investigada por microscopia eletrônica e análise por EDAX. / The study of the effect of microalloying elements in the chemical composition, microstructure and mechanical properties of the as-welded metaIs obtained by submerged are welding with iron powder addition in High Strength Low Alloy (HSLA) steel were done. Two weld metaIs were made using, BS - 4360 - 50 and USI - SAC - 50 steels, EM - 12K wire, ESAB 400 iron powder and 10.71P experimental flux. Using welding current of 600 A, arc voltage of 34 V, travel speed of 30 cm/min and iron powder flow of 6,7 Kg/h were obtained as-welded metals by single pass into V - groove, that showed good hardenability and refined microstructure. The higher percentage microstructure in the two weld metals was the acicular ferrite. The mechanical tests done were hardness, tensile strength and impact. The weld metal with niobium and vanadium achieve better values of hardness and yield strength than with copper, chromium and nickel weld metal. However, the hardening by solid solution, induced by the high levels of manganese, decreased the impact strength of the two weld metaIs. The non - metallic inclusions nature was investigated by electronic microscopy and EDAX analysis.

The works deals with the possibilities of using non-standard fraction of fine crushed aggregate in route base layers. Goal of my thesis is research of using material from specific location. Theoretical part summarizes basic knowledge regarding bound mixtures and their normative requirements. Practical part of my thesis describes my various mixture design and following testing and determination of design properties by official and experimental tests. The conclusion summarizes the researched outputs and findings, which confirm the future possibilities of using this material in base layers.

This diploma thesis is divided into two parts, theoretical and practical. The is a review om the topic of recycled asphalt pavement and recycled concrete and their possible use in road construction in the theoretical part. The individual chapters deal with describing these materials, their production, and their use in construction layers of pavements. In the next chapters the attention is also paid to their problematic features and foreign experience using these materials in pavements. In the practical part, laboratory samples of recycled asphalt pavement and recycled concrete and their mixtures with cement are tested. The main purpose is to verify the applications of these mixtures of recycled asphalt pavement and recycled concrete in the bonded base layers of the pavement. Another purpose is to compare how these mixtures individual properties with different proportions of both components and different amounts of cement will be different. In the end, the two mixtures with the best properties was selected and the modulus of elasticity was experimentally determined for the possibility of replacing the currently used base layers and the economic evaluation of this design was made.

The master thesis dealing with problematic about durability of concrete, with use of recycled concrete and addition of silica additions. Predominant for resistance of concrete constructions is surface layer, through which aggressive gasses and liquids penetrate from surrounding environment. The most important indicator of concrete durability is ability of surface layer transmissions of aggressive substants. In experimental part will be defined the actual state of surface layer by normal testing methods. The transmissions of surface layer will be tested on concrete cubes. Tests for transmissions of air (method TORRENT), of water (method ISAT), of acid gases (dept of carbonation by quick test in 98% CO2) will be carried out and also strength tests. Assessment of positive or negative influence of additions and amount of cement on durability and mechanical properties of concrete will be discussed in conclusion.

The topic of this master's thesis is the development of composite materials based on inorganic binders for use in extreme conditions. It means especially geopolymeric or alkali activated materials (AAM) based composites. The theoretical part of this thesis summarizes knowledges about the development and use of alkali-activated materials, their structure and mechanisms of their formation. It also deals with the applicable raw materials for AAM and their exciters, which are in particular water glass and sodium hydroxide. There also have been a summary of the effects of high temperatures and chemicals on the mechanical properties of AAM and the requirements of standard EN 1504-3 for repairing materials. The task of the practical part was to develop a repair mortar for concrete structures based on AAM so that its production was as simple as possible, ie one-component materials. Gradually six recipes have been develeoped. Test specimens made from these recipes have been putted to selected tests according to the requirements of ČSN EN 1504-3.

In the theoretical part of the thesis are generally characterized hydraulically bound mixtures, their types, classification systems, manufacturing technology and the laying. There are also described experiences from abroad with the use secondary and recycled materials in hydraulically bound mixtures. The practical part deals with the experimental verification of the possibility of the use of secondary materials in hydraulically bound mixtures in construction of road infrastructure. In road laboratory Institute of road structures Brno university of technology was the five proposed mixtures, an assessment of their parameters with regard to the possibility of using these mixtures in the road sub-base layers. The work is also aimed at comparison of results elasticity modules reached laboratory testing and experimental measurements on road polygon.