This diploma thesis deals with the ideological design and realization of digital room thermostat and a temperature sensor selection. The device is designed as three units communicating wirelessly. Outdoor unit and control units sensor provide data for the control circuit of microcontroller ATmega16. Microcontroller choose the boiler operation based on senzor data. Thermostat can be remotely controled

This work deals with the regulation of the water temperature in a small garden pool. The practical part consists of practical design control unit garden pool which is based on knowledge of the ambient air temperature and the temperature of the solar panel, evaluates and controls the filtration pump bypass valve and solar panel. Temperature sensing is done using digital sensors DS18B20 more 1-Wire bus. The control unit is formed by 2x4 matrix keyboard keys. All data are displayed on the alphanumeric display 2x16 characters. Control element is a microcontroller Atmel ATmega 3250PA. Furthermore, discussed in this thesis is data transfer using Bluetooth module.

Bc. David Morávek Tyre temperature measurement on moving vehicle with of infrared pyrometer OS100 MT, IAE, 2008, page 70, picture 41 Problemacy of recording the temperature and tyre pressure on driven car is processed in this diploma work. Suitable measuring chain was set up. Censor holders for this type of measurement were designed and produced. Driving exams and tests are depicted in this work, too. We came to the conclusion that tyre temperature depends on lengthways and transverse acceleration of the car and also on it’s load.

This diploma work deals with relationship between composition and mechanical properties of polymeric composite with polypropylene matrix and magnesia hydroxide as a filler. The influence of content of filler (20,40,60 w.%) and temperature (-30°C +60°C) on dynamic fracture toughness is observed. The regresion function describing the dependence of studied mechanical properti on temperature for all experimental materials where found. Experimental data were confront with data gained on the same materials then 10 years ago and influence of time on mechanical properties of follow - up composites is evaluate.

The thesis deals with the design of the multivariable automatic control system of aftercooling process in the brick industry tunnel kiln. Theoretical part submits the facilities of controlled systems identification and the design methods of uni and multi variable systems. In the practical section is cleared up the principal of the aftercooling process and its identification based on the measured data. The output of the thesis is the design and the analysis of multivariable system with the conservation of the control circuit autonomy.

The thesis deals with the measurement system for determining the thermal efficiency of the newly developed types of solar absorbers. Measuring equipment allows simultaneous indoor or outdoor thermal efficiency detection of up to four samples absorbers. Emphasis is placed on the flow and heat transfer medium temperature changes. For this purpose is used Biotech FCH-m-POM-LC and LM35DZ sensors. Sensor signal is transferred to a PC using the measuring module NI USB-6221. Here it is further processed by proposed evaluation program. The software is implemented in LabVIEW integrated development environment. In a final part are performed a verification measurements to assess system performance and evaluate the thermal efficiency of various types of solar absorbers. This path is also demonstrated high efficiency applications absorbent layer coating color RABSORB 5.

Diploma thesis deals with the design of a vibration isolated platform for low temperature scanning tunneling microscope working under ultra high vacuum (UHV STM). Cooling of the microscope is done by liquid helium using a flow cryostat designed in Institute of Scientific Instruments of the AS CR. In the thesis, general requirements of designing of an ultra high vacuum compatible devices are discussed, as well as the ways of vibrational isolation and damping. Also some ways how to restrict the transfer of vibration between vacuum devices and surroundings are mentioned. This knowledge is then applied to the design of the antivibrational microscope platform compatible with low temperature usage. For better understanding of vibrational transfer and damping, a real model of the designed platform is made and vibrational transfer characteristics are measured and compared with the theory.

Ground granulated blast furnace slag is a by-product of the steel industry and is often used in combination with ordinary Portland cement as a binder in concrete. When concrete is exposed to high temperatures, physical and chemical transformations lead to significant loss of mechanical properties. This study aims to investigate the effect of high temperatures and rehydration on the mechanical properties, microstructure and phase composition of alkali activated slag. The results of the research could make an important contribution to decisions made concerning the reconstruction of structures affected by fire. In suitable cases it would be possible to regenerate parts of a structure instead of totally rebuilding it.

This thesis deals with the design of overall concept of distributed system which is used for temperature, pressure and humidity measurement. The system is adapted to be used in instrument transformers and sensors production hall of ABB s.r.o. Brno. Firstly, the requirements for the measuring system are defined. After that market research focused on sensors and measurement modules is performed. The selected sensor is afterwards built into own measurement module for which hardware and software part is designed. The work continues with design of local and remote database of measured values. Besides, the PC software used for local and remote data storage is designed afterwards. The components of the measurement system are tested in the final part of the thesis.

The diploma thesis deals with the topic of rapid day-to-day drops of air temperature. The research part of the thesis is focused on physical-geographical factors that affect the air temperature. Furthermore, the most common methods used to detect interdiurnal changes in air temperature are presented. Abrupt drops in air temperature were detected on the basis of the maximum and minimum daily air temperature at a total of 33 meteorological stations for the period from 1st January 1970 to 31st December 2019. The aim was to describe the regularities of the distribution of extreme drops in air temperature in both temperature characteristics, and to describe the influence of different physical-geographical conditions on the magnitude and seasonality of decline events. The thesis also describes the influence of the prevailing weather situation (according to HMÚ typing) on extreme decreases in both temperature characteristics. It was proved that the shape of the relief has a significant effect on the seasonality of decreases, especially the minimum air temperatures. Stations on convex relief are characterized by a more balanced distribution of these events during the year, while at stations on concave relief there are the largest decreases in the minimum air temperature, especially in winter. The influence...