CPAP is the most common treatment for moderate to severe sleep apnea in adults. Despite its efficacy, patients’ safety, comfort and compliance are issues to be considered and improved in CPAP design. The issues include condensation, carbon dioxide in inhaled air, humidity and temperature of inhaled air. When a CPAP user breaths deeply, there will be some air not fully expelled and may be driven back into the heated air delivery tube (HADT). An interest has existed in what impacts this so called reverse flow may bring about to the CPAP use. The main objectives of this research are to quantify the reverse flow and its influence on carbon dioxide re-breathing, delivered humidity to the patient and condensation in the HADT. Within this thesis, two computer models of the CPAP system have been constructed on Simulink™ in the Matlab™ environment. One is about the CPAP fluid dynamic performance and carbon dioxide re-breathing and the other is on thermodynamic performance. The models can predict the dynamic behaviour of the CPAP machine. They are able to mimic the breath induced airflow fluctuation, and flow direction changes over wide real working ranges of ambient conditions, settings and coefficients. These models can be used for future analysis, development, improvement and design of the machine. The fluid dynamic and thermodynamic models were experimentally validated and they have proved to be valuable tool in the work. The main conclusions drawn from this study are: • Reverse flow increases when breaths load increases and pressure setting decreases. • Reverse flow does not definitely add exhaled air to the next inhalation unless the reverse flow is relatively too much. • Mask capacity does not influence the reverse flow. • The exhaled air re-breathed is mainly due to that stays in the mask, therefore larger mask capacity increases the exhaled air re-breath and the percentage of exhaled air in next inhalation drops when the breath load increases. • Deep breathing does not significantly change the total evaporation in chamber. • When deep breathing induced reverse flow occurs, condensation occurs or worsens in the HADT near the mask. This happens only when the humidity of the airflow from the CPAP is much lower than that of the exhaled air and the tube wall temperature is low enough for condensation to occur. • The deep breathing and reverse flow do not significantly influence the average inhaled air temperature. • The overall specific humidity in inhaled air is lower under deep breathing. • Mask capacity does not influence the thermal conditions in the HADT and the inhaled air specific humidity. Also the mask capacity does not significantly influences the inhaled air temperature.

The extent and dynamics of permafrost are tightly linked to the distribution and movement of water in arctic landscapes. As the Arctic warms more rapidly than the global average, profound changes are expected in both permafrost and hydrology; however, much is still not known about the interactions between these two systems. The aim of this thesis is to provide new knowledge on the links between permafrost and hydrology under varying environmental conditions and across different scales. The objectives are to (i) determine how permafrost distributions and patterns in morphology are linked to hydrology, (ii) determine how groundwater flow influences ground temperature dynamics in permafrost landscapes, and (iii) explore the mechanisms that link permafrost to groundwater and streamflow dynamics. A range of methods have been applied within the four studies (papers I-IV) comprising the thesis: geophysical (ground penetrating radar and electrical resistivity tomography) and GIS techniques for mapping and analyzing permafrost distributions and related morphology; numerical modeling of coupled heat and water fluxes for mechanistic understanding permafrost-hydrological links; and statistical analyses for detecting trends in streamflow associated with permafrost thaw. Combining these various methods here allows for, and may be considered a prerequisite for, novel insights to processes. The thesis also presents statistical analyses of field observations of ground temperatures, ground- and surface water levels, as well as lake and shore morphological variables. Discontinuous permafrost peatlands are heterogeneous environments regarding permafrost distributions and thickness which is manifested in surface systems such as lake geometries. In these environments, lateral groundwater fluxes, which are not considered in most permafrost models, can significantly influence ground temperature dynamics, especially during high groundwater gradient conditions. River discharge data provide a potential for monitoring catchment-scale changes in permafrost, as the magnitude and seasonality of groundwater fluxes feeding into streams are affected by the distribution of permafrost. This thesis highlights the need to understand water and permafrost as an integrated system with potential internal feedback processes. For example, permafrost thaw can lead to increases in groundwater discharge which in turn can lead to increased heat transfer through the ground, resulting in further acceleration of permafrost thaw rates. / <p>At the time of the doctoral defense, the following paper was unpublished and had a status as follows: Paper 3: Manuscript.</p>

No description available.

CPAP is the most common treatment for moderate to severe sleep apnea in adults. Despite its efficacy, patients’ safety, comfort and compliance are issues to be considered and improved in CPAP design. The issues include condensation, carbon dioxide in inhaled air, humidity and temperature of inhaled air. When a CPAP user breaths deeply, there will be some air not fully expelled and may be driven back into the heated air delivery tube (HADT). An interest has existed in what impacts this so called reverse flow may bring about to the CPAP use. The main objectives of this research are to quantify the reverse flow and its influence on carbon dioxide re-breathing, delivered humidity to the patient and condensation in the HADT. Within this thesis, two computer models of the CPAP system have been constructed on Simulink™ in the Matlab™ environment. One is about the CPAP fluid dynamic performance and carbon dioxide re-breathing and the other is on thermodynamic performance. The models can predict the dynamic behaviour of the CPAP machine. They are able to mimic the breath induced airflow fluctuation, and flow direction changes over wide real working ranges of ambient conditions, settings and coefficients. These models can be used for future analysis, development, improvement and design of the machine. The fluid dynamic and thermodynamic models were experimentally validated and they have proved to be valuable tool in the work. The main conclusions drawn from this study are: • Reverse flow increases when breaths load increases and pressure setting decreases. • Reverse flow does not definitely add exhaled air to the next inhalation unless the reverse flow is relatively too much. • Mask capacity does not influence the reverse flow. • The exhaled air re-breathed is mainly due to that stays in the mask, therefore larger mask capacity increases the exhaled air re-breath and the percentage of exhaled air in next inhalation drops when the breath load increases. • Deep breathing does not significantly change the total evaporation in chamber. • When deep breathing induced reverse flow occurs, condensation occurs or worsens in the HADT near the mask. This happens only when the humidity of the airflow from the CPAP is much lower than that of the exhaled air and the tube wall temperature is low enough for condensation to occur. • The deep breathing and reverse flow do not significantly influence the average inhaled air temperature. • The overall specific humidity in inhaled air is lower under deep breathing. • Mask capacity does not influence the thermal conditions in the HADT and the inhaled air specific humidity. Also the mask capacity does not significantly influences the inhaled air temperature.

Dans cette thèse, nous avons étudié la dynamique d'aimantation selon deux échelles de temps en utilisant la technique pompe-sonde magnéto-optique résolue en temps. A l'échelle de la picoseconde, la précession de l'aimantation est induite par des impulsions acoustiques dans des structures multicouches composées de deux couches ferromagnétique séparées par une couche métallique (Ni/Au/Py) avec différentes épaisseurs. La synchronisation de la précession des couches ferromagnétiques couplées a été observée. La modification de la précession de l'aimantation d'une couche de Ni est due l'interaction d'échange intercouche avec la couche Py. A l'échelle de 50fs, nous avons étudié la dynamique magnéto-optique cohérente, athermale, thermale et la relaxation des charges et des spins dans (Ni, Co et Fe) par impulsions de 11 fs dans un régime de faible perturbation. L'interaction spin-orbite et l'interaction d'échange jouent un rôle significatif dans la désaimantation ultrarapide. / In this thesis, we have investigated the magnetization dynamics at picosecond and femtosecond time scale using time resolved magneto-optical pump probe technique. At picosecond time scale, the magnetization precession is induced by ultrafast acoustic pulses in a three layered structure with two ferromagnetic layers separated by varying thickness of metallic spacer layer (Ni/Au/Py). The magnetization precession dynamics of the Ni layer is modified due to the interlayer exchange interaction with the Py layer and the synchronized precession of the coupied ferromagnetic layers has been observed. At the timescale of 50fs, coherent magneto-optical, non-thermal, thermal and relaxation dynamics of charges and spins in ferromagnetic transition metals (Ni, Co and Fe) is studied by using 11fs optical pulses in a very low perturbation regime. The spin orbit interaction and exchange interaction play a significant role in the demagnetization of the ferromagnetic metals induced by femtosecond pulses.

The different topics covered in this thesis include photosensitivity in germanosilicate fibers/glasses and application of fiber Bragg grating sensors in simultaneous strain and temperature discrimination. Fiber Bragg Gratings are wavelength dispersive refractive index structures manufactured through ultra-violet (UV) exposure of optical fibers. Their applications range from wavelength division multiplexing filters, dispersion compensators and fiber laser resonators for telecommunication applications to different types of point or distributive sensors for a variety of applications. One aim of this thesis has been to understand the mechanism of photosensitivity in germanosilicate fibers/preforms. Studies undertaken in this part of the thesis include thermal dynamics of Fiber Bragg Gratings and nano-indentation on ultra-violet irradiated germanosilicate glass preforms. An interesting, periodic appearance of a new peak has been observed in the reflected spectrum of Bragg grating inscribed in a germanosilicate fiber during thermal treatment. The new peak occurs on the longer wavelength side of the spectrum during heating and on the shorter wavelength side during cooling, following an identical reverse dynamics. A commercial grating with 99.9% reflectivity also shows a similar decay dynamics. The observed temperature induced distortion in refractive index modulation profile has been understood in the light of compaction-densification model. It is proposed that during the fabrication process of a grating, the modulation in the thermal expansion coefficient brought about by the interference fringes results in a non-uniform expansion throughout the grating length which in turn results in the distortion of the refractive index profile with increase/decrease in temperature. Since the reflection spectrum of a grating can be approximated as the Fourier transform of the refractive index profile, any distortion in the index profile results in the observed anomalous behaviour in the reflection spectrum. Nano-indentation studies have been performed to measure the changes in mechanical properties of a glass preform subjected to different levels of ultra-violet exposure. The results reveal that short term exposure leads to an appreciable increase in the Young’s modulus suggesting the densification of the glass, confirming the compaction-densification model. However, on prolonged exposure, the Young’s modulus decreases, which provides the first direct evidence of dilation in the glass leading into the Type IIA regime. The present results rule out the hypothesis that continued exposure leads to an irreversible compaction and prove that index modulation regimes are intrinsic to the glass matrix. In the second part of the thesis, three different schemes have been proposed for the use of Fiber Bragg Gratings as strain-temperature discriminating sensors: (a) The first method is based on the measurement of the different characteristic wavelength shifts of two types of gratings. Strain and temperature sensitivities of a Type I Bragg grating (G1) in germania doped silica fiber, fabricated under normal conditions, and zero strain, are compared with that of a Bragg grating inscribed under pre-strained condition (G2). Experimental results show that both, strain and temperature sensitivities of G1 and that of G2 are different. Based on this study, we have proposed an approach which enables simultaneous discrimination of axial strain and temperature. (b) In the second method, a single sensing element has been used to encode strain and temperature into an additional parameter other than the wavelength shift. The thermal out-diffusion of germanium from the core of a photosensitive fiber under elevated temperature is exploited to form a Fabry-Perot filter with a single Fiber Bragg Grating. The filter is fabricated using the standard phase-mask technique and one-time exposure. Energy Dispersive X-Ray analysis is used to measure the out-diffusion. The filter is used as a sensor for simultaneous measurement and discrimination of strain and temperature. The proposed technique, where a single grating is used to discriminate the parameters, provides a large advantage over other existing methods. (c) In the third method, a compact design based on cross-wire arrangement of Fiber Bragg Gratings having identical Bragg resonance and different reflectivity is proposed for simultaneously sensing strain (uniaxial) and temperature. Two gratings are assembled orthogonal to each other on an aluminium base. The cross-wire design allows the two sensors to experience the same temperature but different strain. The gratings are identified by their respective reflectivity and, strain and temperature are resolved from the shift in Bragg wavelength. The proposed design exploits the fact that strain is a vector and temperature is a scalar parameter. This sensor has wide industrial application in discriminating strain from temperature effects.

The world is constantly striving towards a more sustainable living, where every part of contribution is greatly appreciated. When it comes to heating of buildings, district heating is often the main source of heat. During specific times, peak demands are created by the tenants who are demanding a lot of heat at the same time. This demand peak puts a high load on the piping system as well as the need for certain peak boilers that run on non-environmental friendly peak fuel. One solution that is presented in this degree project that solves the time difference between production and demand is by utilizing thermal storage solutions. A dynamic district heated building model is developed with proper heat propagation in the pipelines, thermal inertia in the building and heat losses through the walls of the building. This is all done utilizing 4th generation district heating temperatures. Modelica is the tool that was used to simulate different scenarios, where the preheating of indoor temperature is done to mitigate the possibility for demand peaks. Using an already existing model, implementation and adjustments are done to simulate thermal storage and investigate its effectiveness in a 4th generation district heating system. The results show that short-term energy storage is a viable solution in concrete buildings due to high building mass. However, combining both 4th generation district heating with storage in thermal mass is shown not to be suitable due to low temperatures of supply water, which is not able to increase the temperature of the building’s mass enough.