The purpose of this study is to investigate forced convection of air through open cell foams. It can be numerically investigated either by implementing the time efficient macroscopic models or computationally expensive microscopic models. However, during the course of this study, it was observed that the macroscopic models are not sufficient for determining the desired key parameters. Nevertheless, it is still possible that these macroscopic models can be used to design an application accurately with minimum time efforts if the concerned key parameters are already known through other means. Accordingly, in this work, a methodology is developed to determine the desired key parameters by implementing the microscopic models, which are further used into the macroscopic models for designing different applications. To validate the proposed methodology, a set of steady state and transient forced convection experiments were performed for a set of ceramic foams having different pore diameter (10−30 PPI) and porosity (0.79−0.87) for a superficial velocity in the range of 0.5−10 m/s.

The purpose of this study is to investigate forced convection of air through open cell foams. It can be numerically investigated either by implementing the time efficient macroscopic models or computationally expensive microscopic models. However, during the course of this study, it was observed that the macroscopic models are not sufficient for determining the desired key parameters. Nevertheless, it is still possible that these macroscopic models can be used to design an application accurately with minimum time efforts if the concerned key parameters are already known through other means. Accordingly, in this work, a methodology is developed to determine the desired key parameters by implementing the microscopic models, which are further used into the macroscopic models for designing different applications. To validate the proposed methodology, a set of steady state and transient forced convection experiments were performed for a set of ceramic foams having different pore diameter (10−30 PPI) and porosity (0.79−0.87) for a superficial velocity in the range of 0.5−10 m/s.

In automotive body-in-white production, presshardened 22MnB5 steel is the most widely used ultra-high-strength steel grade. Welding is the most important faying technique for this steel type, as other faying technologies often cannot deliver the same strength-to-cost ratio. In order to conduct precise numerical simulations of the welding process, flow stress curves and thermophysical properties from room temperature up to the melting point are required. Sheet metal parts made out of 22MnB5 are welded in a presshardened, that is, martensitic state. On the contrary, only flow stress curves for soft annealed or austenitized 22MnB5 are available in the literature. Available physical material data does not cover the required temperature range or is not available at all. This work provides experimentally determined hot-flow stress curves for rapid heating of 22MnB5 from the martensitic state. The data is complemented by a comprehensive set of thermophysical data of 22MnB5 between room temperature and melting. Materials simulation methods as well as a critical literature review were employed to obtain sound thermophysical data. A comparison of the numerically computed nugget growth curve in spot welding with experimental welding results ensures the validity of the hot-flow stress curves and thermophysical data presented.

The horizontal twin-roll casting (TRC) process is an energy saving and cost-efficient method for producing near-net-shape sheets of castable metals for light-weight production. In order to investigate the TRC process numerically, a code is generated in OpenFOAM and the commercial software STAR-CCM+ is used. Both are validated with the Stefan problem, the gallium melting test case, and a continuous casting experiment for magnesium AZ31. Different solidification models are tested that are similar to solution domain definitions and solid-fraction temperature relations. The comparison with temperature measurements of the MgF GmbH Freiberg pilot plant and the final microstructure exhibits good correlation. Sensitivity studies are carried out for thermophysical properties of AZ31 as well as pilot plant parameters. Furthermore, the rolls are incorporated into the simulation to determine the effect of a location-dependent heat-transfer coefficient. Finally, the results are compared to a second pilot plant situated at the Helmholtz-Centre Geesthacht in order to explore differences and similarities. / Das horizontales Gießwalzen ist eine energiesparende und kostengünstige Methode zur Erzeugung von Flachprodukten, die im Leichtbau verwendet werden. Um dieses Verfahren numerisch zu untersuchen wurde ein Programmcode in OpenFOAM entwickelt und die kommerzielle Software STAR-CCM+ verwendet, wobei beide mit dem Stefan Problem, dem Schmelzen von Gallium und Messdaten des Stranggusses von Magnesium AZ31 validiert wurden. Verschiedene Erstarrungsmodelle werden ebenso getestet wie Variationen des Simulationsbereiches und Feststoff-Temperatur-Verläufe. Vergleiche mit Temperaturmessdaten der Pilotanlage MgF GmbH Freiberg und der finalen Mikrostruktur zeigen gute Übereinstimmungen. Sensitivitätsanalysen werden durchgeführt, um die Einflüsse von thermophysikalischen Eigenschaften und Anlagenparametern abzuschätzen. Des Weiteren werden die Walzen in die Simulation mit einbezogen, um den Effekt eines lokal veränderlichen Wärmeübergangskoeffizienten zu beurteilen. Schließlich werden die Ergebnisse mit denen einer zweiten Pilotanlage am Helmholtz-Zentrum Geesthacht verglichen. / Le laminage de coulée continue horizontal possède une faible consommation d’énergie et est bon marché pour la production des feuilles de métaux coulables utilisés dans la construction légère. Afin d’examiner ce processus numériquement, un code est généré dans OpenFOAM et le logiciel commercial STAR-CCM+ est utilisé, tous les deux sont validés en utilisant le problème de Stefan, la fusion du gallium et la coulée continue verticale de magnésium AZ31. Plusieurs modèles de solidification sont testés, ainsi que la variation du domaine de simulation, et des rélations entre la teneur en matière solide et la température. Des comparaisons avec des résultats de mesures de la température à l’installation pilote de MgF GmbH Freiberg ainsi que la microstructure donnent des bons résultats. Des analyses de sensibilité sont effectuées afin d’évaluer l’influence des propriétés thermophysiques et des paramètres de l’installation. De plus, les cylindres sont intégrés dans la simulation pour estimer l’impact du coefficient de transfert de chaleur dépendant du lieu. Finalement, les résultats sont comparés avec ceux du Helmholtz-Centre Geesthacht.

The horizontal twin-roll casting (TRC) process is an energy saving and cost-efficient method for producing near-net-shape sheets of castable metals for light-weight production. In order to investigate the TRC process numerically, a code is generated in OpenFOAM and the commercial software STAR-CCM+ is used. Both are validated with the Stefan problem, the gallium melting test case, and a continuous casting experiment for magnesium AZ31. Different solidification models are tested that are similar to solution domain definitions and solid-fraction temperature relations. The comparison with temperature measurements of the MgF GmbH Freiberg pilot plant and the final microstructure exhibits good correlation. Sensitivity studies are carried out for thermophysical properties of AZ31 as well as pilot plant parameters. Furthermore, the rolls are incorporated into the simulation to determine the effect of a location-dependent heat-transfer coefficient. Finally, the results are compared to a second pilot plant situated at the Helmholtz-Centre Geesthacht in order to explore differences and similarities. / Das horizontales Gießwalzen ist eine energiesparende und kostengünstige Methode zur Erzeugung von Flachprodukten, die im Leichtbau verwendet werden. Um dieses Verfahren numerisch zu untersuchen wurde ein Programmcode in OpenFOAM entwickelt und die kommerzielle Software STAR-CCM+ verwendet, wobei beide mit dem Stefan Problem, dem Schmelzen von Gallium und Messdaten des Stranggusses von Magnesium AZ31 validiert wurden. Verschiedene Erstarrungsmodelle werden ebenso getestet wie Variationen des Simulationsbereiches und Feststoff-Temperatur-Verläufe. Vergleiche mit Temperaturmessdaten der Pilotanlage MgF GmbH Freiberg und der finalen Mikrostruktur zeigen gute Übereinstimmungen. Sensitivitätsanalysen werden durchgeführt, um die Einflüsse von thermophysikalischen Eigenschaften und Anlagenparametern abzuschätzen. Des Weiteren werden die Walzen in die Simulation mit einbezogen, um den Effekt eines lokal veränderlichen Wärmeübergangskoeffizienten zu beurteilen. Schließlich werden die Ergebnisse mit denen einer zweiten Pilotanlage am Helmholtz-Zentrum Geesthacht verglichen. / Le laminage de coulée continue horizontal possède une faible consommation d’énergie et est bon marché pour la production des feuilles de métaux coulables utilisés dans la construction légère. Afin d’examiner ce processus numériquement, un code est généré dans OpenFOAM et le logiciel commercial STAR-CCM+ est utilisé, tous les deux sont validés en utilisant le problème de Stefan, la fusion du gallium et la coulée continue verticale de magnésium AZ31. Plusieurs modèles de solidification sont testés, ainsi que la variation du domaine de simulation, et des rélations entre la teneur en matière solide et la température. Des comparaisons avec des résultats de mesures de la température à l’installation pilote de MgF GmbH Freiberg ainsi que la microstructure donnent des bons résultats. Des analyses de sensibilité sont effectuées afin d’évaluer l’influence des propriétés thermophysiques et des paramètres de l’installation. De plus, les cylindres sont intégrés dans la simulation pour estimer l’impact du coefficient de transfert de chaleur dépendant du lieu. Finalement, les résultats sont comparés avec ceux du Helmholtz-Centre Geesthacht.