Cardiovascular diseases (CVD) remain one of the leading causes of deaths worldwide. The formation and presence of aneurysm is a very important question in the study of this CVDs. An aneurysm is a balloon-like bulge on a blood vessel which forms over time. An aneurysm is usually considered to be a result of weakening of the blood vessel walls, this definition has stood over many years without being conclusively proven. Eventually, the aneurysm could clot or burst due to degradation of the aneurysm wall and accumulation of blood. The latter would lead to internal bleeding and result in a stroke. Local hemodynamics have been found to be very important in the study of the evolution of an aneurysm. In this study, a steady flow experimental investigation was conducted using planar Particle Image Velocimetery (PIV) on a rigid flow phantom of an idealised geometry consisting of a curve parent artery and a spherical aneurysm located on the outer convex side of the curvature. The flow phantom was fabricated directly using a commercially available desktop Stereolithography (STL) 3D printer instead of the more conventional investment casting method using a core. Although 3D printing technologies have been around for many years, the fabrication of flow phantoms by direct printing is still largely under-explored. This thesis details the results of investigation into the optimal printing and post-printing procedures required to produce a flow phantom of suitable clarity and transparency. Other important areas of concern such as the geometric accuracy, surface topography and refractive index of the final model are also investigated. A planar PIV is conducted to study the impact of flow rates on the local flow field in and around the aneurysm and their impact on the wall shear stress. It was found that direct 3D printing is appropriate for the fabrication of flow phantoms suitable for PIV or other flow visualisation techniques. It reduces the complexities and time needed compared to the conventional investment casting methods. It was observed that the optical properties of the printed material such as the high refractive index (RI) and the transmittivity of light could cause a problem in large models. From the PIV measurements it was found that flow rates affect the flow field in both the parent artery and the aneurysm. First, high velocities were observed on the outer curvature of the parent artery. Secondly the centre of rotation in the aneurysm is not at the geometric centre but is displaced slightly in the direction of the flow. Finally, the flow rate affects the angle in which flow enters the aneurysm from the parent vessel. This change in the flow angle affects the flow within the aneurysm. A higher flow rate in the parent artery increases the incident angle which brings the centre of rotation closer to the geometric centre of the aneurysm, this changes the location and magnitude of high velocities and hence the local wall shear stress (WSS) on the wall of the aneurysm. This may have implications in the evolution of aneurysms. / Mechanical and Industrial Engineering

Biological markers (i.e., biomarkers) are essential in clinical and epidemiological studies as they may provide mechanistic insights into the developmental origins of disease, as well as improve diagnostic testing and risk assessment for disease prevention. However, major challenges remain due to the lack of rapid yet selective analytical methods for high throughput screening that are also amenable to volume-restricted specimens. This thesis includes two major research themes that take advantage of capillary electrophoresis (CE) separations, including (1) the targeted analysis of urinary iodide and thiocyanate for assessment of nutritional adequacy and tobacco smoke exposures in the population, and (2) the discovery of new biomarkers in sweat specimens that may improve universal newborn screening programs for cystic fibrosis (CF) infants beyond impaired chloride transport. Chapter II examines the prevalence and risk factors associated with iodine deficiency in 24 h urine samples collected from 800 participants across four clinical sites in Canada as part of the Prospective Urban and Rural Epidemiological (PURE) study when using CE with UV detection in conjunction with sample self-stacking. Importantly, regional variations in iodine status were revealed with participants from Quebec City and Vancouver at greater risk for iodine deficiency than Hamilton and Ottawa. Overall, iodine supplement use, thyroxine prescription, urinary sodium excretion, and self-reported dairy intake were found to be protective factors against iodine deficiency. Chapter III applied a validated CE assay to measure urinary thiocyanate as a biomarker of tobacco smoke and dietary exposures in an international cohort of 1000 participants from the PURE study spanning 14 countries with varied income status, smoking habits, and diet quality. Current smokers residing in high-income countries had the highest extent of cyanide exposure indicative of greater harms from tobacco smoke compared to middle- and low-income countries after adjusting for smoking intensity and other covariates. Chapter IV introduces a rapid CE method with indirect UV detection to simultaneously measure sweat chloride and bicarbonate from presumptive CF infants’ residual sweat samples. Although bicarbonate did not provide clinical value in neonatal CF diagnosis, sweat chloride testing by CE may reduce test failure rates due to insufficient volumes from infants in a clinical setting. Lastly, Chapter V applied an untargeted strategy to characterize the sweat metabolome from presumptive CF infants when using multisegment injection-capillary electrophoresis-mass spectrometry (MSI-CE-MS). A panel of sweat metabolites were found to discriminate CF from non-CF (i.e., unaffected carriers) infants, including aspartic acid, glutamine, oxoproline, and pilocarpic acid, which also correlated with sweat chloride. The clinical utility of these sweat metabolites to prognosticate late-onset CF infants from indeterminate sweat chloride test results was also explored. In summary, this thesis contributes innovative separation methods for biomarker screening and discovery in clinical and epidemiological studies for the prevention and early treatment of human diseases that benefit from optimal nutrition. / Dissertation / Doctor of Philosophy (PhD)

Gas-phase thermolysis is a long-known and well established method for the preparation of reactive species. It is, however, limited to relatively volatile substances, which are easily vaporised. In the present work, the solution-spray technique for preparative scale was developed. With this technique, it is possible to subject low-volatile substances, which hardly vaporise even under high-vacuum conditions, to gas-phase thermolysis. By utilising oil nozzles used in heating and burner systems, it was possible to integrate a stable solution-spray into the existing flash-vacuum-pyrolysis system. The influence of several variables, such as flow-rate, pressure, temperature and solvent was determined. The solution-spray technique was applied in [3,3]-sigmatropic rearrangements of certain propargyl thiocyanates to the corresponding allenyl isothiocyanates. Furthermore, the parent compound propa-1,2-dienyl isothiocyanate was reacted with various sterically demanding primary and secondary amines to form 2-amino-1,3-thiazoles in moderate to excellent yields. Based on this, a catalyst-free four-center three-component reaction was developed. 2-Amino-1,3-thiazoles with complex substituents in 5-position at the heterocyclic ring are formed. Reaction mechanisms are discussed to explain the occurance of a highly substituted 1,3-thiazine structure. The influence of reaction temperature, concentrations and solvent were determined and are also discussed. It was shown that 2-amino-5-methyl-1,3-thiazoles are the apparently first aromatic substance class, that readily undergoes Prins-type 1,3-dioxane ring-formation. / Die Gasphasenthermolyse ist eine lang bekannte und etablierte Methodik zur Synthese reaktiver Spezies. Sie ist allerdings auf flüchtige Substanzen mit einer guten Verdampfbarkeit beschränkt. Für schwerflüchtige Verbindungen, welche sich selbst im Hochvakuum nur mäßig oder gar nicht in die Gasphase bringen lassen, wurde in der vorliegenden Arbeit die Solution-Spray-Technik für die Anwendung im präparativen Maßstab entwickelt. Unter Verwendung von Ölzerstäuberdüsen, wie sie in der Heizungs- und Brennertechnik Anwendung finden, wurde die Erzeugung eines stabilen Lösungs-Sprays in die vorhandene Blitzvakuumpyrolyse-Technik integriert. Der Einfluss verschiedener Variablen, wie Flussrate, Druck, Temperatur und Lösungsmittel wurde untersucht. Die Solution-Spray-Technik wurde für die [3,3]-sigmatrope Umlagerung bestimmter Propargylthiocyanate zu Allenyl-isothiocyanaten angewendet. Des Weiteren wurde Propa-1,2-dienylisothiocyanat – das einfachste Allenylisothiocyanat – mit diversen sterisch anspruchsvollen primären und sekundären Aminen in mäßigen bis exzellenten Ausbeuten zu 2-Amino-1,3-thiazolen umgesetzt. Darauf aufbauend konnte eine Vier-Zentren-drei-Komponenten-Reaktion entwickelt werden. Es entstehen in hohen Ausbeuten 2-Amino-1,3-thiazole mit komplexen Substituenten an der 5-Position des Heterocyclus. Reaktionsmechanismen werden diskutiert um die alternative Bildung einer hochsubstituierten 1,3-Thiazinstruktur zu erklären. Der Einfluss von Reaktionstemperatur, Konzentration und Lösungsmittel auf das Produktverhältnis wurde ebenfalls untersucht und wird diskutiert. Es konnte gezeigt werden, dass 2-Amino-5-methyl-1,3-thiazole als offenbar erste aromatische Substanzklasse sehr gute Substrate für die Bildung von 1,3-Dioxanen nach Prins darstellen.

Gas-phase thermolysis is a long-known and well established method for the preparation of reactive species. It is, however, limited to relatively volatile substances, which are easily vaporised. In the present work, the solution-spray technique for preparative scale was developed. With this technique, it is possible to subject low-volatile substances, which hardly vaporise even under high-vacuum conditions, to gas-phase thermolysis. By utilising oil nozzles used in heating and burner systems, it was possible to integrate a stable solution-spray into the existing flash-vacuum-pyrolysis system. The influence of several variables, such as flow-rate, pressure, temperature and solvent was determined. The solution-spray technique was applied in [3,3]-sigmatropic rearrangements of certain propargyl thiocyanates to the corresponding allenyl isothiocyanates. Furthermore, the parent compound propa-1,2-dienyl isothiocyanate was reacted with various sterically demanding primary and secondary amines to form 2-amino-1,3-thiazoles in moderate to excellent yields. Based on this, a catalyst-free four-center three-component reaction was developed. 2-Amino-1,3-thiazoles with complex substituents in 5-position at the heterocyclic ring are formed. Reaction mechanisms are discussed to explain the occurance of a highly substituted 1,3-thiazine structure. The influence of reaction temperature, concentrations and solvent were determined and are also discussed. It was shown that 2-amino-5-methyl-1,3-thiazoles are the apparently first aromatic substance class, that readily undergoes Prins-type 1,3-dioxane ring-formation. / Die Gasphasenthermolyse ist eine lang bekannte und etablierte Methodik zur Synthese reaktiver Spezies. Sie ist allerdings auf flüchtige Substanzen mit einer guten Verdampfbarkeit beschränkt. Für schwerflüchtige Verbindungen, welche sich selbst im Hochvakuum nur mäßig oder gar nicht in die Gasphase bringen lassen, wurde in der vorliegenden Arbeit die Solution-Spray-Technik für die Anwendung im präparativen Maßstab entwickelt. Unter Verwendung von Ölzerstäuberdüsen, wie sie in der Heizungs- und Brennertechnik Anwendung finden, wurde die Erzeugung eines stabilen Lösungs-Sprays in die vorhandene Blitzvakuumpyrolyse-Technik integriert. Der Einfluss verschiedener Variablen, wie Flussrate, Druck, Temperatur und Lösungsmittel wurde untersucht. Die Solution-Spray-Technik wurde für die [3,3]-sigmatrope Umlagerung bestimmter Propargylthiocyanate zu Allenyl-isothiocyanaten angewendet. Des Weiteren wurde Propa-1,2-dienylisothiocyanat – das einfachste Allenylisothiocyanat – mit diversen sterisch anspruchsvollen primären und sekundären Aminen in mäßigen bis exzellenten Ausbeuten zu 2-Amino-1,3-thiazolen umgesetzt. Darauf aufbauend konnte eine Vier-Zentren-drei-Komponenten-Reaktion entwickelt werden. Es entstehen in hohen Ausbeuten 2-Amino-1,3-thiazole mit komplexen Substituenten an der 5-Position des Heterocyclus. Reaktionsmechanismen werden diskutiert um die alternative Bildung einer hochsubstituierten 1,3-Thiazinstruktur zu erklären. Der Einfluss von Reaktionstemperatur, Konzentration und Lösungsmittel auf das Produktverhältnis wurde ebenfalls untersucht und wird diskutiert. Es konnte gezeigt werden, dass 2-Amino-5-methyl-1,3-thiazole als offenbar erste aromatische Substanzklasse sehr gute Substrate für die Bildung von 1,3-Dioxanen nach Prins darstellen.