A repetitive control method for output voltage control of a three phase uninterruptible power supply (UPS) with isolation transformer is investigated. In the method voltage control loop is employed in the stationary dq frame. The controller eliminates the periodic errors on the output voltages due to inverter voltage nonlinearity and load disturbances. The controller design and implementation details are given. The controller is implemented on a 5-kVA UPS prototype which is constructed in laboratory. Linear and nonlinear loads for balanced and unbalanced load operating conditions are considered. The steady-state and dynamic performance of the control method are investigated in detail. The theory of the control strategy is verified by means of simulations and experiments.

A method for high performance output voltage control of a four-leg inverter based three-phase transformerless UPS is proposed. Voltage control loop is employed and the method employs stationary frame resonant filter controllers for the fundamental and harmonic frequency components. A capacitor current feedback loop provides active damping and enhances the output voltage dynamic performance. The controller design and implementation details are given. Linear and nonlinear loads for balanced and unbalanced load operating conditions are considered. The steadystate and dynamic performance of the UPS are investigated in detail. A scalar PWM method with implementation simplicity and high performance is proposed and implemented. The control and PWM methods are proven by means of theory, simulations, and experiments.

The study designs and constructs a three-phase to three-phase direct AC&ndash / AC matrix converter based surface mounted permanent magnet synchronous motor (PMSM) drive system. First, the matrix converter topologies are analyzed and the state-space equations describing the system have been derived in terms of the input and output variables. After that, matrix converter commutation and modulation methods are investigated. A four-step commutation technique based on output current direction provides safe commutation between the matrix converter switches. Then, the matrix converter is simulated for both the open-loop and the closed-loop control. For the closed-loop control, a current regulator (PI controller) controls the output currents and their phase angles. Advanced pulse width modulation and control techniques, such as space vector pulse width modulation and field oriented control, have been used for the closed-loop control of the system. Next, a model of diode-rectified two-level voltage source inverter is developed for simulations. A comparative study of indirect space vector modulated direct matrix converter and space vector modulated diode-rectified two-level voltage source inverter is given in terms of input/output waveforms to verify that the matrix converter fulfills the two-level voltage source inverter operation. Following the verification of matrix converter operation comparing with the diode-rectified two-level voltage source inverter, the simulation model of permanent magnet motor drive system is implemented. Also, a direct matrix converter prototype is constructed for experimental verifications of the results. As a first step in experimental works, filter types are investigated and a three-phase input filter is constructed to reduce the harmonic pollution. Then, direct matrix converter power circuitry and gate-driver circuitry are designed and constructed. To control the matrix switches, the control algorithm is implemented using a DSP and a FPGA. This digital control system measures the output currents and the input voltages with the aid of sensors and controls the matrix converter switches to produce the required PWM pattern to synthesize the reference input current and output voltage vectors, as well. Finally, the simulation results are tested and supported by laboratory experiments involving both an R-L load and a permanent magnet synchronous motor load. During the tests, the line-to-line supply voltage is set to 26 V peak value and a 400 V/3.5 kW surface mounted permanent magnet motor is used.

State estimation plays an important role in modern power systems. The errors in the telemetered measurements and the connectivity information of the network will greatly contaminate the estimated system state. This dissertation provides solutions to suppress the influences of these errors. A two-stage state estimation algorithm has been utilized in topology error identification in the past decade. Chapter II discusses the implementation of this algorithm. A concise substation model is defined for this purpose. A friendly user interface that incorporates the two-stage algorithm into the conventional state estimator is developed. The performances of the two-stage state estimation algorithms rely on accurate determination of suspect substations. A comprehensive identification procedure is described in chapter III. In order to evaluate the proposed procedure, a topology error library is created. Several identification methods are comparatively tested using this library. A remote measurement calibration method is presented in chapter IV. The un-calibrated quantities can be related to the true values by the characteristic functions. The conventional state estimation algorithm is modified to include the parameters of these functions. Hence they can be estimated along with the system state variables and used to calibrate the measurements. The measurements taken at different time instants are utilized to minimize the influence of the random errors. A method for auto tuning of measurement weights in state estimation is described in chapter V. Two alternative ways to estimate the measurement random error variances are discussed. They are both tested on simulation data generated based on IEEE systems. Their performances are compared. A comprehensive solution, which contains an initialization process and a recursively updating process, is presented. Chapter VI investigates the errors introduced in the positive sequence state estimation due to the usual assumptions of having fully balanced bus loads/generations and continuously transposed transmission lines. Several tests are conducted using different assumptions regarding the availability of single and multi-phase measurements. It is demonstrated that incomplete metering of three-phase system quantities may lead to significant errors in the positive sequence state estimates for certain cases. A novel sequence domain three-phase state estimation algorithm is proposed to solve this problem.

Pulse width modulation (PWM) rectifiers are extensively used in battery charger, regulated dc voltage source, UPS systems, ac line conditioner and motor drives. The conventional control schemes for these rectifiers require PLL, transformations, and input voltage sensing, which increase the cost and complexity of the controller. Simple control schemes based on resistance emulation control are developed in this thesis work for different PWM boost rectifiers. Modeling, analysis and design methods for these rectifier systems are presented. The effect of computational delay involved in digital implementation on the performance of the above rectifier systems is studied. A single-switch boost rectifier system is presented, which operates in DCM and in CCM for an output power less than and greater than 50% rated load, respectively, exploiting the best features of both the operating modes. A generalized feedforward control is presented to improve the dynamic response of output voltage of single-phase boost rectifiers against input voltage, load current and reference voltage disturbances. Feedforward control requires additional voltage and/or current measurements. A state observer is presented for estimating the inductor current of a buck rectifier, and two disturbance observers are presented to estimate the input voltage and the load current of a boost rectifier. These observers eliminate the need of additional sensors for implementing the feedforward control. The resistance emulation control is extended to four-wire PWM rectifier. Two control methods are presented. The first method makes the input currents of the rectifier proportional to their respective input voltages, while the second one balances its input currents even under unbalanced input voltage condition. A detailed analysis of line and neutral current distortions of four-wire converter is presented. A three-carrier based PWM scheme is presented, which significantly reduces the neutral current of the rectifier compared to conventional PWM scheme, when three single-phase inductors are used, and considerably reduces both line and neutral current distortions, when a three-limb inductor is used. A regenerative test setup containing two back-to-back connected three-phase PWM converters is presented for testing high-power converters in the active and reactive power circulation mode. The proposed scheme considerably reduces the cost of testing, and hence, the overall production cost of the converters compared to load-bank testing. A mathematical model is presented for the above system. A suitable control method is presented to control the two converters of the back-to-back system. A new PWM scheme is presented, which considerably reduces the requirement of the dc bus voltage of the back-to-back system compared to conventional PWM schemes. All theoretical predictions are experimentally validated. The experimental results are presented.

Με τη διατριβή έγινε ανασκόπηση των πιο γνωστών θεωριών που διέπουν τις πολυφασικές ροές. Ακολούθησε συλλογή και κριτική αξιολόγηση των θεωρητικών μοντέλων. Εκπονήθηκαν δύο προγράμματα σε Η/Υ, τόσο για την ομογενή ροή όσο και τη χωριστή ροή. Έγινε σύγκριση των θεωρητικών με υπάρχοντα πειραματικά αποτελέσματα. Σχεδιάστηκε και κατασκευάστηκε πειραματική διάταξη. Λήφθηκαν πειραματικές μετρήσεις και έγινε αξιολόγησή τους και σύγκριση με θεωρητικά αποτελέσματα. Προτάθηκε μέθοδος διόρθωσης της πρόβλεψης λειτουργίας μιας υδροπνευματικής αντλίας με τη βοήθεια του μοντέλου ‘drift-flux’ (μέθοδος CoSM). Προτάθηκαν νέοι ροϊκοί χάρτες κατάλληλοι για την παρουσίαση της λειτουργίας των υδροπνευματικών αντλιών, τον υπολογισμό του κλάσματος κενού και την μετάβαση των ροϊκών καταστάσεων. Προτάθηκε τρόπος προσδιορισμού της μετάβασης ‘slug-churn’ με απλή φωτογραφική μέθοδο (camera) και χρήση του μοντέλου ‘drift-flux’. Τα αποτελέσματα της διατριβής (πειράματα, μέθοδος CoSM, ροϊκοί χάρτες και μετάβαση slug-churn) παρουσιάστηκαν σε συνέδρια και επιστημονικά περιοδικά. / This PhD thesis deals with multiphase flows and air-lift pumps. All well-known theories concerning these two scientific fields are presented and analyzed in detail. Two computational codes were developed for homogeneous two-phase and separated three-phase flow. A comparison between theoretical results and experimental data followed. An experimental investigation was performed in a lab scale air-lift pump installation at Fluid Mechanics Laboratory, University of Patras. A new method for the precise prediction of the performance of a two-phase air-lift pump with the aid of drift-flux model was presented (CoSM method). New regime maps were introduced suitable for air-lift pump presentations. That means the direct view of the flow behaviour inside the air-lift pump, void fraction calculation and the regime transitions. An experimental method was presented for the prediction of slug-churn transition in two-phase flow, using a camera and ‘drift-flux’ model. The results of this work were presented in International Conferences and Journals.

Η παρούσα διπλωματική εργασία πραγματεύεται τη μελέτη και κατασκευή ενός μετατροπέα για την οδήγηση ενός μονοφασικού επαγωγικού κινητήρα. Η εργασία αυτή εκπονήθηκε στο Εργαστήριο Ηλεκτρομηχανικής Μετατροπής Ενέργειας του Τμήματος Ηλεκτρολόγων Μηχανικών και Τεχνολογίας Υπολογιστών της Πολυτεχνικής Σχολής του Πανεπιστημίου Πατρών. Σκοπός είναι η μελέτη και κατασκευή ενός τριφασικού αντιστροφέα τάσης για τη λειτουργία και τον έλεγχο των στροφών ενός μονοφασικού επαγωγικού κινητήρα. Αρχικά μελετάται η βασική αρχή λειτουργίας του μονοφασικού επαγωγικού κινητήρα και αναλύονται οι τεχνικές εκκίνησης που χρησιμοποιούνται για σύνδεση του κινητήρα απευθείας στο δίκτυο. Ακόμα παρουσιάζονται τα ισοδύναμα κυκλώματα λειτουργίας του μονοφασικού επαγωγικού κινητήρα, η εξίσωση της ηλεκτρομαγνητικής ροπής του και προσομοιώνεται η λειτουργία του για τη μελέτη της στατικής συμπεριφοράς του. Στη συνέχεια γίνεται μια θεωρητική ανάλυση του κυκλώματος του τριφασικού αντιστροφέα τάσης που κατασκευάστηκε, καθώς και όλων των υπόλοιπων κυκλωμάτων που είναι αναγκαία για τη λειτουργία του. Επιπροσθέτως αναλύεται η μέθοδος παλμοδότησης των διακοπτικών στοιχείων του αντιστροφέα τάσης, που είναι η "Ημιτονοειδής Διαμόρφωση του Εύρους των Παλμών" (SPWM). Στο επόμενο βήμα αναλύονται τα τεχνικά χαρακτηριστικά όλων των κυκλωμάτων που κατασκευάστηκαν, και περιγράφεται ο κώδικας του προγράμματος του μικροελεγκτή, που χρησιμοποιήθηκε για την παραγωγή των παλμών. Τέλος, παραθέτουμε παλμογραφήματα και μετρήσεις που προέκυψαν από τα πειράματα που διενεργήθηκαν μετά την ολοκλήρωση της κατασκευής. / This diploma thesis discourse the analysis and construction of a converter topology for single phase induction motor drives. The project was based in the Laboratory of Electromechanical Energy Conversion of the department of Electrical and Computer Engineering of School Engineering of University of Patras. The objective of this project is the analysis and construction of a three phase voltage inverter to control the speed of a single phase induction motor. The first stage of this work is the study of the basic principle of operation of the single phase induction motor and the analysis of the starting techniques, used for the direct connection to the power grid. The equivalent circuits of the running single phase induction motor and the equation of the electromagnetic torque are also presented in this project. Following, there is a theoretical analysis of the three phase voltage inverter circuit, as well of all the remaining circuit, necessary for its function. Moreover the method of pulse generation for the switching elements of the voltage inverter is analyzed, which is the “Sinusoidal Pulse Width Modulation”. The next step is the analysis of the technical characteristics all of the circuits developed, as well the description of the program code for the microcontroller, used to produce the pulses. Finally oscillograph figures and measurements, occurred from the experiments transacted after the finalization of the construction, are adduced.

Η παρούσα διπλωματική εργασία έχει ως αντικείμενο την μελέτη και τη μοντελοποίηση ενός υβριδικού συστήματος, που αποτελείται από φωτοβολταϊκά και κυψέλες καυσίμου τα οποία τροφοδοτούν ένα μικροδίκτυο. Το φορτίο το οποίο καλείται το σύστημα να καλύψει είναι 30kW και 15kVar. Για τη μοντελοποίηση του συστήματος χρησιμοποιείται το πρόγραμμα σχεδίασης και προσομοίωσης ηλεκτρικών συστημάτων PSCAD. Στην εργασία αυτή το ενδιαφέρον επικεντρώνεται στη συμπεριφορά του συστήματος στη μόνιμη κατάσταση λειτουργίας και στη συμπεριφορά σε κάποια μεταβατατικά φαινόμενα. Τα μεταβατικά φαινόμενα που εξετάζονται είναι τα εξής: - Συμπεριφορά συστήματος σε μεταβολές της ηλιοφάνειας. - Απόκριση συστήματος σε μεταβολές του φορτίου. - Τριφασικό και μονοφασικό βραχυκύκλωμα με τη γη στη γραμμή. Στο κεφάλαιο 1 γίνεται αναφορά στις ανανεώσιμες πηγές, στην εξέλιξή και στην προοπτική τους στο μέλλον. Στη συνέχεια περιγράφονται τα διάφορα είδη των υβριδικών συστημάτων και γίνεται αναφορά για τη διεσπαρμένη παραγωγή και τα μικροδίκτυα. Στο κεφάλαιο 2 περιγράφεται η λειτουργία των φωτοβολταϊκών κυττάρων, παρουσιάζονται οι I-V και P-V χαρακτηριστικές και στη συνέχεια ακολουθεί αναλυτική περιγραφή του μοντέλου της φωτοβολταϊκής συστοιχίας που θα χρησιμοποιήσουμε στην προσομοίωση στο PScad. Στο κεφάλαιο 3 περιγράφεται η λειτουργία των κυψελών καυσίμων και παρουσιάζονται τα διάφορα είδη κυψελών που υπάρχουν στις μέρες μας. Εν συνεχεία ακολουθεί αναλυτική περιγραφή της λειτουργίας της κυψέλης καυσίμου πολυμερούς ηλεκτρολυτικής μεμβράνης PEM FC καθώς αυτό το είδος των κυψελών καυσίμου χρησιμοποιούμε στο σύστημά μας. Τέλος, κατασκευάζεται το μοντέλο της PEM FC και ακολουθεί η αναλυτική περιγραφή του μοντέλου. Στο κεφάλαιο 4 γίνεται αναφορά στους dc/dc μετατροπείς ανύψωσης τάσης και στις περιοχές λειτουργίας τους. Εν συνεχεία γίνεται διαστασολόγηση του ανυψωτή τάσης και παρουσιάζεται το σύστημα ελέγχου του. Επίσης μελετάται η λειτουργία του ανυψωτή ως ανιχνευτή του σημείου μέγιστης ισχύος της φωτοβολταϊκής συστοιχίας και γίνεται προσομοίωση των κυψελών και της φωτοβολταϊκής συστοιχίας με τους dc/dc μετατροπείς που χρησιμοποιούνται. Στο κεφάλαιο 5 ακολουθεί η περιγραφή της λειτουργίας των μονοφασικών και τριφασικών αντιστροφέων DC/AC και παρουσιάζεται αναλυτικά η στρατηγική της διαμόρφωσης εύρους παλμών (PWM). Τέλος, γίνεται υπολογισμός των τιμών του φίλτρου που τοποθετείται στην έξοδο του αντιστροφέα και στη συνέχεια προσομοιώνεται και μελετάται το μοντέλο του αντιστροφέα που χρησιμοποιούμε στο σύστημά μας. Στο κεφάλαιο 6 γίνεται η πλήρη προσομοίωση του συστήματος. Περιγράφονται επίσης και τα μοντέλα του φορτίου, του Μ/Σ, του δικτύου και της μηχανής παραγωγής σφαλμάτων. Τέλος, παρουσιάζονται και περιγράφονται τα αποτελέσματα των μελετών που πραγματοποιούνται στο σύστημα (απόκριση συστήματος σε κανονικές συνθήκες, απόκριση συστήματος για μεταβολή της ηλιοφάνειας, μελέτη συστήματος στη μεταβολή του φορτίου, προσομοίωση συστήματος για σφάλματα στη γραμμή). / The current diploma thesis presents the study and simulation of a hybrid system, which consists of a Photovoltaic Array (PV) and a Fuel Cell stack (FC), which supports a microgrid. The critical load that the system supports is 30kW and 15kVar. For the system modelling the program of designing and simulation of electric systems PSCAD is used. At this project the interest is focused in the behavior of system in the permanent situation of operation and in the behavior in certain transient phenomena. The transient phenomena that are examined are the following: - Behavior of the system in variations in solar insolation. - System’s response to variations of the load. - Fault analysis (single line to ground and three-phase line to ground short circuit). In Chapter 1 there is a description of renewable energy sources, their development and prospects in the future. Afterwards, the different kinds of hybrid systems are mentioned and there is a reference in distributed generation and microgrids. In Chapter 2 the function of photovoltaic cells and different kinds of photovoltaic technologies are described. Furthermore, I-V and P-V characteristic are presented and then follows an analytical description of the photovoltaic model that we use in our simulation in PScad. In Chapter 3 , the function of the Fuel Cells is described and the different kinds of fuel cells are presented. Afterwards, there is an analytical description of the proton exchange membrane fuel cells (PEM FC) as we use this kind of FC in our system. Finally, the PEM FC model is constructed and an analytical description of the model is made. The Chapter 4 entails information for the dc/dc boost converters and their operating modes. Subsequently the control system of the dc/dc boost converter is presented. Finally, the utilization of the boost converter as a maximum power point tracker is examined and the simulation of the FV and PV with the boost converter is presented. In Chapter 5 there is a description of the function of the single-phase and three-phase dc/ac inverters and the technique of the pulse-width modulation (PWM) is presented. Finally, the value of the output filter of the inverter is calculated and then the model of the dc/ac inverter, which we use in our system, is simulated. In Chapter 6 there is a simulation of the whole system. Furthermore, the models of the load, the transformer and the fault generator are described. Finally, the results of the simulations for which the system was tested is presented (system response to normal conditions, system response to changes in the insolation, System’s response to variations of the load, system response to grid faults).

Orientador: Falcondes José Mendes de Seixas / Resumo: Este trabalho tem como objetivo a proposição de um retificador trifásico boost semi-controlado, com correção ativa do fator de potência, que faça uso de técnicas de controle de razão cíclica variável, visando reduzir o conteúdo harmônico de corrente em baixa frequência. O conversor proposto opera em modo de condução descontínua, desta forma, a corrente de entrada segue uma envoltória senoidal. Além disso, devido ao modo de condução, o conversor apresenta a entrada em condução da chave com corrente nula, diminuindo assim, as perdas por chaveamento. Inicialmente, são apresentados, estudos teóricos da topologia em questão e, por meio de gráficos e equações, verifica-se a distorção harmônica imposta devida à operação com razão cíclica constante. Funções que permitam a variação permanente da razão cíclica, durante um ciclo da rede, serão apresentadas. Tais funções possuem o intuito de minimizar a distorção harmônica da corrente de entrada, com foco principal na 5ª componente harmônica. Resultados de simulação demonstram eficácia das técnicas de controle por razão cíclica variável e apontam redução no conteúdo harmônico de corrente. Resultados experimentais demonstram conteúdo harmônico de corrente em torno de 18% para operação do conversor com razão cíclica constante. A utilização de razão cíclica variável proporciona uma redução no conteúdo harmônico de corrente para 13%, resultando em um aumento do fator de potência. / Abstract: This work aims propose a three-phase rectifier boost half-controlled, with power factor correction, that makes use variable duty cycle control techniques, in order to reduce the harmonic content of current in low frequency. The proposed converter operates in a discontinuous current conduction mode, this way, the input current is naturally corrected. Moreover, due to the conduction mode, the converter presents entry in conduction of switch with null current, thus decreasing, the losses by switching. Initially, are presented theoretical studies of the topology in question and, through of graphs and equations, the harmonic distortion imposed by operation due constant duty cycle is verified. Functions that allow permanently the variation of duty cycle, during a network cycle, are presented. These functions have as main objective minimize the harmonic distortion in the input current, with focus in the 5th harmonic component. Simulation results demonstrate efficacy of techniques by variable duty cycle control and indicate a reducing of harmonic content of current. Experimental results demonstrate a reducing around 18% for operation with constant duty cycle. The use of variable duty cycle provides a reducing around 13%, resulting in an increase of the power factor. / Mestre

Submitted by ALESSANDRO LUCINDO DA LUZ null (aledaluz@hotmail.com) on 2018-01-10T01:24:32Z No. of bitstreams: 1 Operacao flexivel conversores_ALuz.pdf: 10997918 bytes, checksum: 18fe1f6d3eba73d11bf63fab8cf0a0be (MD5) / Approved for entry into archive by Maria Marlene Zaniboni null (zaniboni@bauru.unesp.br) on 2018-01-10T11:41:48Z (GMT) No. of bitstreams: 1 luz_al_me_bauru.pdf: 10997918 bytes, checksum: 18fe1f6d3eba73d11bf63fab8cf0a0be (MD5) / Made available in DSpace on 2018-01-10T11:41:48Z (GMT). No. of bitstreams: 1 luz_al_me_bauru.pdf: 10997918 bytes, checksum: 18fe1f6d3eba73d11bf63fab8cf0a0be (MD5) Previous issue date: 2017-11-13 / Este trabalho de mestrado descreve uma estratégia de operação multifuncional e flexível aplicado a conversores trifásicos CC-CA (inversores) conectados à rede de distribuição de energia elétrica. A estratégia proposta é capaz de injetar potência ativa na rede e compensar correntes de distúrbios (reativos, desbalanço e harmônicos) simultaneamente. O maior objetivo desta operação flexível é de melhorar a Qualidade de Energia Elétrica em um ponto de acoplamento comum (PAC) permitindo a compensação total ou parcial destes distúrbios ou fatores que degradam a Qualidade de Energia Elétrica. O fator de potência é o principal fator de qualidade a ser observado e ele é calculado através da Teoria da Potência Conservativa – CPT. Entretanto, com base no fator de potência medido pelo lado da rede de distribuição e o fator de potência desejado, um coeficiente de compensação – k é calculado para o ajuste das correntes de compensação dos distúrbios que geram a potência não ativa. / This paper depicts a multifunctional and flexible control strategy applied in three-phase inverters, which are connected to the distribution network. The proposed strategy is able to inject active power into the electrical grid and compensate current disturbances (reactive, harmonics and unbalance) simultaneously. The main goal of this flexible strategy is to improve the Power Quality at the point of common coupling (PCC) allowing full or partial compensation of disturbances. Power factor is the main quality index observed and it is calculated according to Conservative Power Theory - CPT. Therefore, based on the power factor measured in the grid side and the desired value for the power factor, a compensation coefficient - k is calculated continuously adjusting the amplitude of the compensation current.