1 |
Algorithm and Model Development for Innovative High Power AC TransmissionJanuary 2015 (has links)
abstract: This thesis presents research on innovative AC transmission design concepts and focused mathematics for electric power transmission design. The focus relates to compact designs, high temperature low sag conductors, and high phase order design. The motivation of the research is to increase transmission capacity with limited right of way.
Regarding compact phase spacing, insight into the possibility of increasing the security rating of transmission lines is the primary focus through increased mutual coupling and decreased positive sequence reactance. Compact design can reduce the required corridor width to as little as 31% of traditional designs, especially with the use of inter-phase spacers. Typically transmission lines are built with conservative clearances, with difficulty obtaining right of way, more compact phase spacing may be needed. With design consideration significant compaction can produce an increase by 5-25% in the transmission line security (steady state stability) rating. In addition, other advantages and disadvantages of compact phase design are analyzed. Also, the next two topics: high temperature low sag conductors and high phase order designs include the use of compact designs.
High temperature low sag (HTLS) conductors are used to increase the thermal capacity of a transmission line up to two times the capacity compared to traditional conductors. HTLS conductors can operate continuously at 150-210oC and in emergency at 180-250oC (depending on the HTLS conductor). ACSR conductors operate continuously at 50-110oC and in emergency conditions at 110-150oC depending on the utility, line, and location. HTLS conductors have decreased sag characteristics of up to 33% compared to traditional ACSR conductors at 100oC and up to 22% at 180oC. In addition to what HTLS has to offer in terms of the thermal rating improvement, the possibility of using HTLS conductors to indirectly reduce tower height and compact the phases to increase the security limit is investigated. In addition, utilizing HTLS conductors to increase span length and decrease the number of transmission towers is investigated. The phase compaction or increased span length is accomplished by utilization of the improved physical sag characteristics of HTLS conductors.
High phase order (HPO) focuses on the ability to increase the power capacity for a given right of way. For example, a six phase line would have a thermal rating of approximately 173%, a security rating of approximately 289%, and the SIL would be approximately 300% of a double circuit three phase line with equal right of way and equal voltage line to line. In addition, this research focuses on algorithm and model development of HPO systems. A study of the impedance of HPO lines is presented. The line impedance matrices for some high phase order configurations are circulant Toeplitz matrices. Properties of circulant matrices are developed for the generalized sequence impedances of HPO lines. A method to calculate the sequence impedances utilizing unique distance parameter algorithms is presented. A novel method to design the sequence impedances to specifications is presented. Utilizing impedance matrices in circulant form, a generalized form of the sequence components transformation matrix is presented. A generalized voltage unbalance factor in discussed for HPO transmission lines. Algorithms to calculate the number of fault types and number of significant fault types for an n-phase system are presented. A discussion is presented on transposition of HPO transmission lines and a generalized fault analysis of a high phase order circuit is presented along with an HPO analysis program.
The work presented has the objective of increasing the use of rights of way for bulk power transmission through the use of innovative transmission technologies. The purpose of this dissertation is to lay down some of the building blocks and to help make the three technologies discussed practical applications in the future. / Dissertation/Thesis / Doctoral Dissertation Electrical Engineering 2015
|
2 |
Condensation Heat Transfer Of R-134A On Micro-Finned Tubes : An Experimental StudySen, Biswanath 06 1900 (has links)
Eco-friendly non-CFC refrigerants were introduced in the Air Conditioning and Refrigeration industry during the last few years to reduce damage to the stratospheric ozone layer. The HFC refrigerant R-134a, which has zero Ozone Depletion Potential (ODP), is being used extensively as a replacement for R-12 and also in some centrifugal chillers as a replacement for R-11. However, the disadvantage of R-134a is its comparatively high global warming potential (GWP). Owing to energy crisis and also to reduce the indirect warming impact resulting from electrical energy usage, the new refrigeration systems should be operated at the lowest possible condensing temperatures. In view of this, several active and passive techniques for augmentation of condensation heat transfer and reduction of condensation temperature are gaining increasing attention. Passive augmentation methods are more popular than active ones. To this end, micro-finned tubes of various geometrical shapes are being explored for compact heat exchangers in the refrigeration industry as the best choice.
Towards understanding the enhancement in condensation heat transfer coefficients in micro-finned tubes, a test facility has been fabricated to measure the condensing coefficients for R-134a refrigerant. Condensation experiments have been conducted on single plain and finned tubes of outer diameter 19 mm with a refrigerant saturation temperature of 400C and tube wall temperatures 350C, 320C, 300C and 280C respectively. Water is used as the cooling medium inside the tubes with the flow rate varying from 180 lph to 600 lph. The condensing coefficient typically ranged from 0.9 – 1.4 kW/(m2 K) for plain tubes and from 4.2 to 5.8 kW/(m2 K) for the finned tubes. The results of the plain v tube are found to compare favourably with the Nusselt’s theory, leading to a validation of the experimental procedure. Upon comparing the results of finned and plain tubes, it is found that provision of fins result in an enhancement factor of 3.6 to 4.6 in the condensation heat transfer coefficients. This level of enhancement is larger than that resulting from the enhanced surface area of the finned tube surface, suggesting that, apart from the extended area, the surface tension forces play an important role in the augmentation process by driving the condensate from the fin crests to the valleys in between the fins. The measured augmentation factors have also been cross-checked using the Wilson plot method. Detailed error analysis has been performed to quantify the uncertainty in the condensation heat transfer coefficient.
The performance of a bank of tubes has been determined based on the measurements carried out on practical condensers of two large chillers with refrigerating capacities of 500 TR and 550 TR. On comparing the finned tube bank results and the single finned tube results, it is found that the average condensation heat transfer coefficient in a bank of tubes having N rows varies as N ¯1/6. The deterioration is in agreement with the relation proposed by Kern.
|
3 |
Design and Analysis of an adaptive λ-Tracking Controller for powered Gearshifts in automatic TransmissionsLoepelmann, Peter 30 March 2015 (has links) (PDF)
To meet the continuously increasing goals in vehicle fuel efficiency, a number of measures are taken in automotive powertrain engineering, such as the combination of electric drives and conventional combustion engines in hybrid vehicles or the increase in gear ratios. This development leads to more complex powertrain systems, such as automatic transmissions. At the same time, the need for complex control systems is increased to achieve this desired functionality.
Automatic transmissions are controlled by an electro-hydraulic control unit that governs all operations such as gear shifting and starting. Since most of the control software is designed in the form of open-loop control, most of the operations have to be calibrated manually. Thus, there exists a large number of calibration parameters in the control software that have to be tuned individually for each combination of engine, transmission and vehicle model. This process is therefore time-consuming and costly. Hence, it would be advantageous to reduce the need for calibration and in the end shorten the development process for automatic transmissions by reducing software complexity while maintaining functionality and performance.
The goal of this thesis is to replace parts of the control software responsible for conducting the gearshifts that require extensive tuning by implementing control systems that have no need for calibration: adaptive high-gain λ-tracking controllers. In order to obtain the control parameters, i.e., the feedback gains, without calibration, an adaption law is implemented that continuously computes these parameters during operation of the controller. Thus, calibration is no longer needed. Since the system has to be high-gain-stabilizable, an extensive system analysis is conducted to determine whether an adaptive λ-tracking controller can be implemented. A nonlinear model of the clutch system dynamics is formulated and investigated.
As a result, high-gain stability is proven for the system class and validated in simulation. Following the stability analysis, the devised adaptive controller is implemented into the control software running on the series production transmission control unit. Extensive simulations with a comprehensive vehicle model running the extended transmission software are conducted to design and to test the adaptive controllers and their underlying parameters during transmission operation in order to evaluate the control performance. The control software containing the adaptive controller is then implemented in two distinct vehicles with different automatic transmissions equipped with series production control hardware for the purpose of hardware experiments and validation. The resulting reduction of calibration efforts is discussed.
|
4 |
Design and Analysis of an adaptive λ-Tracking Controller for powered Gearshifts in automatic TransmissionsLoepelmann, Peter 14 November 2014 (has links)
To meet the continuously increasing goals in vehicle fuel efficiency, a number of measures are taken in automotive powertrain engineering, such as the combination of electric drives and conventional combustion engines in hybrid vehicles or the increase in gear ratios. This development leads to more complex powertrain systems, such as automatic transmissions. At the same time, the need for complex control systems is increased to achieve this desired functionality.
Automatic transmissions are controlled by an electro-hydraulic control unit that governs all operations such as gear shifting and starting. Since most of the control software is designed in the form of open-loop control, most of the operations have to be calibrated manually. Thus, there exists a large number of calibration parameters in the control software that have to be tuned individually for each combination of engine, transmission and vehicle model. This process is therefore time-consuming and costly. Hence, it would be advantageous to reduce the need for calibration and in the end shorten the development process for automatic transmissions by reducing software complexity while maintaining functionality and performance.
The goal of this thesis is to replace parts of the control software responsible for conducting the gearshifts that require extensive tuning by implementing control systems that have no need for calibration: adaptive high-gain λ-tracking controllers. In order to obtain the control parameters, i.e., the feedback gains, without calibration, an adaption law is implemented that continuously computes these parameters during operation of the controller. Thus, calibration is no longer needed. Since the system has to be high-gain-stabilizable, an extensive system analysis is conducted to determine whether an adaptive λ-tracking controller can be implemented. A nonlinear model of the clutch system dynamics is formulated and investigated.
As a result, high-gain stability is proven for the system class and validated in simulation. Following the stability analysis, the devised adaptive controller is implemented into the control software running on the series production transmission control unit. Extensive simulations with a comprehensive vehicle model running the extended transmission software are conducted to design and to test the adaptive controllers and their underlying parameters during transmission operation in order to evaluate the control performance. The control software containing the adaptive controller is then implemented in two distinct vehicles with different automatic transmissions equipped with series production control hardware for the purpose of hardware experiments and validation. The resulting reduction of calibration efforts is discussed.
|
Page generated in 0.0167 seconds