Thesis (M.S.)--State University of New York at Binghamton, Biological Sciences Department, 2007. / Includes bibliographical references.

No description available.

No description available.

Small-scale wind turbines were not considered viable in the past due to their poor efficiencies, mainly because of their aerodynamic effects around the irfoil shape. Recently researchers have renewed interest in enhancing the aerodynamic performances of the blades’ designs inspired by the aerodynamic pattern of biological characteristics of insects and marine mammals such as locusts, dragonflies, damselflies, Humpback Whales etc. Bioinspired wing designs have advantages compared to conventional smooth irfoil blades as they can counter the bending forces that the wings experience during flapping. Bio-inspired corrugated airfoil based on dragonfly wing geometries have been reported to perform well compared to conventional airfoil at low Reynolds numbers. Corrugated airfoils reduce flow separation and enhance aerodynamic performance by trapping vortices in the corrugations thus drawing flow towards the airfoil’s surface. This results in the higher lift whilst incurring only marginally higher drag. Such airfoils also have an advantage when it comes to span-wise structural stiffness due to the corrugated cross-sections. Replacing conventional turbine blades by tubercles or corrugated blades could enhance turbine performance by reducing the pressure gradient along the leading edge; however, the aerodynamic effects at the leading edge will depend on the variations of wavelength and amplitude. In this study, two types of computational studies were investigated: Optimising a corrugated airfoil and investigating the aerodynamic effects of a sinusoidal shape at the leading edge of a blade. Previous studies used an idealized geometry based on the dragonfly wing cross-section profile but did not attempt to optimize the geometry. In the present study: a two-dimensional CFD model is constructed using ANSYS Fluent Workbench-Design Explorer to determine the optimal corrugated blade profile for four angles of attack (AOA) from 5° to 20° corresponding to typical AOA of small-scale wind turbine blades. Two modified blades with variations of wavelength and amplitude at the leading edge were studied to investigate the aerodynamic effects. Three-dimensional models were constructed using Qblade software and 3D points were exported to AutoCAD Inventor to generate the CAD model. The governing equations used are continuity and Navier-Stokes equations written in a frame reference rotating with the blade. The CFD package used is ANSYS FLUENT 19.0. The simulation was run under steady-state, using SST-k omega turbulence model. The modifications have improved the aerodynamic performance. The optimised corrugated blade produced a maximum increase of CL and L/D. Both modified blades (1 and 2) had their performances measured separately and compared to that of baseline blade SG6042 (Conventional blade). Modified blade 1 had a lower wavelength and amplitude at the leading edge of 14.3 % and 4 % respectively of the chord. It was noted that the aerodynamic performance decreased by 6%. Modified model 2, on the other hand had a higher wavelength and amplitude at the leading edge. of 40.4 % and 11.9 % respectively of the chord. It was also noted the aerodynamic performance increased by 6%. From the empirical evidence highlighted above, it can be observed that there is a direct correlation between wavelength, amplitude, and aerodynamic performance of the blade. / Electrical and Mining Engineering / M. Tech. (Engineering)

As the understanding of the workings of the biological world expands, biomimetic designs increasingly move into the focus of engineering research studies. For this thesis, two studiesinvolving leading edge vortex generation for lift production as observed in nature were explored intheir respective flow regimes. The first study focused on the steady state analysis of streamwise vortices generated byleading edge tubercles of an adult humpback whale flipper. A realistic scaled model of a humpbackflipper was fabricated based on the 3D reconstruction from a sequence of 18 images taken whilecircumscribing an excised flipper of a beached humpback whale. Two complementary modelswith smooth leading edges were transformed from this original digitized model and fabricatedfor testing to further understand the effect of the leading edge tubercles. Experimentally-obtainedforce and qualitative flow measurements were used to study the influence of the leading edgetubercles. The presence of leading edge tubercles are shown to decrease maximum lift coefficient(Cl ), but increase Cl production in the post-stall region. By evaluating a measure of hydrodynamicefficiency, humpback whale flipper geometry is shown to be more efficient in the pre-stall regionand less efficient in the post-stall region as compared to a comparable model with a smooth leadingedge. With respect to a humpback whale, if the decrease in efficiency during post-stall angles ofattack was only required during short periods of time (turning), then this decrease in efficiencymay not have a significant impact on the lift production and energy needs. For the pursuit ofbiomimetic designs, this decrease in efficiency could have potential significance and should beinvestigated further. Qualitative flow measurements further demonstrate that these force results aredue to a delay of separation resulting from the presence of tubercles.The second study investigated explored the effects of flapping frequency on the passive flowcontrol of a flapping wing with a sinusoidal leading edge profile. At a flapping frequency of f =0.05 Hz, an alternating streamwise vortical formation was observed for the sinusoidal leading edge,while a single pair of vortices were present for the straight leading edge. A sinusoidal leading edgecan be used to minimize spanwise flow by the generation of the observed alternating streamwisevortices. An increase in flapping frequency results in these streamwise vortices becoming stretchedin the path of the wing. The streamwise vortices are shown to minimize spanwise flow even afterbeing stretched. Once instabilities are formed at f ≥ 0:1 Hz due to velocity shearing generatedby the increase in cross-radial velocity, the alternating streamwise vortices begin to break downresulting in a increase of spanwise flow.