No description available.

Yes / Cattle grids are used on roads and tracks to prevent grazing animals from leaving an open space without fencing onto a more controlled area where access to the road from surrounded land is more limited. They are widely used in the UK at the entrances to common and moorland areas where animals are free to roam, but also on private drive entrances. Typically, they consist of a series of metal bars across the road that are spaced so that an animal’s legs would fall through the gaps if it attempted to cross. Below the grid is a shallow pit that is intended to further deter livestock from using that particular crossing point. The sound produced as vehicles cross these devices is a characteristic low frequency “brrrr” where the dominant frequencies relates to the bar passage frequency under the tyres. The sound can be disturbing to riders and their horses and walkers and residents living close by as evidenced by press reports and the need to consider noise aspects in planning for new installations. For this reason and due to the lack of available information on the size and nature of the problem measurements and recordings have been made at a number of sites in Yorkshire in the UK. In addition, questionnaire surveys of residents living close by and façade measurements have also been used to gauge impact. Results show that there is a wide variation in the maximum noise level produced by cattle grids of apparently similar design. This can be related to impact noise produced by the movement of all or part of the grid as the frame comes under impulsive loading as the vehicle crosses. It was further established that some residents living close to the cattle grids were disturbed by the noise, and in some cases vibration, and wanted them removed or suitably modified. Means of reducing the problem are proposed.

Exterior vehicle noise has a very big impact when it comes to environmental noise pollution. Due to the decrease of the other noise sources of a passenger car, like power-train and air turbulence noise in the last decade, the tyre/road noise has become a more important part in the overall noise generation of a vehicle nowadays. It is considered as the main noise source in nearly all driving conditions, especially with increasing vehicle speed. The easiest idea to tackle this pollution is to introduce rules like speed-limits to control the noise at a certain area or time. More interesting, however, is to approach the problem of unwanted noise directly at the source. This Thesis, carried out at Loughborough University, aims to give a better understanding about the basic noise generation mechanisms at the tyre/road interface. Especially, the air related mechanisms of closed cavities are analysed. With the usage of a solid rubber tyre, unique measurements have been carried out and the results are compared to the theories already existing in the literature. These measurements reveal some of the strengths and weaknesses of the current understanding of air related noise generation.

Structures acting as waveguides are quite common withexamples being, construction beams, fluid filled pipes, railsand extruded aluminium profiles. Curved structures like cartyres and pipe-bends may also be considered as waveguides. Wavesolutions in such structures may be found by a method calledthe Waveguide Finite Element Method or WFEM. This method uses afinite element approach on the cross-section of a waveguide tomodel the vibro-acoustic response as a set of linear, coupled,one dimensional, wave-equations. In this thesis six novel waveguide finite elements arederived and validated. These elements are, straight and curvedpre-stressed, orthotropic or anisotropic shell elements,straight and curved fluid elements, and straight and curvedfluid-shell coupling elements. Forced response and input power calculations for infiniteand periodic waveguides are presented. The assembled waveguidemodels can also serve as input for the Super Spectral FiniteElement Method, which enables forced response calculations formore complex boundaries. Furthermore, several properties ofdamped and undamped wave solutions are investigated. Finally, a car tyre model, encompassing for the highlyanisotropic material and the air cavity inside the tyre is setforth. A number of forced response calculations for this modelare presented and compared with measurements with goodagreement. Keywords:wave equation, wave solution, waveguide,finite element, spectral finite element, tyre noise, tyrevibration, input power, shells, pre-stress, fluid-shellcoupling axi-symmetric, two-and-half-dimensional

<p>Structures acting as waveguides are quite common withexamples being, construction beams, fluid filled pipes, railsand extruded aluminium profiles. Curved structures like cartyres and pipe-bends may also be considered as waveguides. Wavesolutions in such structures may be found by a method calledthe Waveguide Finite Element Method or WFEM. This method uses afinite element approach on the cross-section of a waveguide tomodel the vibro-acoustic response as a set of linear, coupled,one dimensional, wave-equations.</p><p>In this thesis six novel waveguide finite elements arederived and validated. These elements are, straight and curvedpre-stressed, orthotropic or anisotropic shell elements,straight and curved fluid elements, and straight and curvedfluid-shell coupling elements.</p><p>Forced response and input power calculations for infiniteand periodic waveguides are presented. The assembled waveguidemodels can also serve as input for the Super Spectral FiniteElement Method, which enables forced response calculations formore complex boundaries. Furthermore, several properties ofdamped and undamped wave solutions are investigated.</p><p>Finally, a car tyre model, encompassing for the highlyanisotropic material and the air cavity inside the tyre is setforth. A number of forced response calculations for this modelare presented and compared with measurements with goodagreement.</p><p><b>Keywords:</b>wave equation, wave solution, waveguide,finite element, spectral finite element, tyre noise, tyrevibration, input power, shells, pre-stress, fluid-shellcoupling axi-symmetric, two-and-half-dimensional</p>