Nowadays, oil resources start to decrease, therefore it is necessary to think about alternative sources of energy. The result of this semester project is a basic overview of the current development of electric and hybrid cars, with potential application in normal operation and the proximity of their main characteristics, such as mileage, price and service when traveling. The energy required to operate the electric stored in batteries are recharged using the power stations, which is also devoted part of the work. The thesis focuses on the design and calculation of power consumption for a defined route of four-wheel electric wheelchair. The conclusion of the thesis deals with the future development of hybrid and electric vehicles, and with the expected trends in the field of power electronics and motors and with the propagation of hybrid vehicles to the customers.

In the flow past bluff bodies for a certain range of velocity a periodical vortex shedding emerges which is known as von Kármán vortex street. This phenomenon causes the periodical alteration of pressure field which affects the body. Should the vortex shedding frequency be similar to the body natural frequency, the amplitude of vibration significantly increases which can lead to fatigue cracking. In the case of water turbines, this phenomenon often affects the stay vanes. Both the vortex shedding frequency and the lift force amplitude can be influenced by the modification of the trailing edge geometry. The aim of this thesis is to use CFD computation in order to find the optimal geometry of the stay vane trailing edge for the specific Francis turbine unit.

The main objective of the presented thesis is to contribute to the development of diagnostic methods for piezoelectric sensor testing. The thesis describes the methods for piezoelectric sensors microcracks identification and diagnostics. The core of the thesis presents the development of a knock sensor prototype, design of suitable methods for the knock sensors diagnosis and evaluation of developed methods with focus on detection of microcracks in the sensor piezoceramic. The last part of the thesis deals with the influence of cracks and splits on the measured data from the piezoelectric transducer. The presented methods are focusing on impedance measurements and sensors frequency response measurements. Known properties of used piezoelectric material as an information source for measurement and diagnosis are provided. The main result of the work is the evaluation of the methods developed for the piezoelectric sensors self-diagnosis.

The aim of the dissertation thesis is the control of the tube bundle on the cyclic fatigue caused by the flow past tube bundle. Fatigue due to flow is caused by flow-induced vibrations. Examined vibrations are caused by the mutual interaction of two phases (solid and liquid). The present work is focused mainly on the interaction of tube bundles with fluid. The current level of knowledge in this field allows to predict mainly static respectively quazi-static loading. These predictions are based on methods of comparing key vibration variables such as frequencies, amplitudes or speeds (see TEMA [1]). In this way, it is possible to determine quickly and relatively precisely the occurrence of a vibrational phenomenon, but it is not possible to quantitatively assess the effect of these vibrations on the damage of to the tube beam and to predict its lifespan, which would require the determination of the temperature field and the distribution of forces from the fluid on the beam. The aim of the work is to evaluate the-state-of-the-art, to perform a numerical simulation of the flow of fluids in the area of shell side under the inlet nozzle. Current methods of numerical analyses very well solve this problem, but at the expense of computing time, devices and expensive licences. The benefit of this work is the use of user-defined function (UDF) as a method for simulating interaction with fluid and structure in ANSYS Fluent software. This work places great emphasis on using the current state of knowledge for verifying and validation. Verifying and validation of results include, for example, experimentally measured Reynolds and Strouhal numbers, the drag coefficients and for example magnitude of pressure coefficient around the tube. At the same time, it uses the finite element method as a tool for the stress-strain calculation of a key part on tube such as a pipe-tube joint. Another benefit of this work is the extension of the graphical design of heat exchanger according to Poddar and Polley by vibration damages control according to the method described in TEMA [1]. In this section, the author points out the enormous influence of flow velocity on both the tube side and the shell side for design of the heat exchanger to ensure faultless operation. As an etalon of damage, the author chose a heat exchanger designated 104 from the Heat Exchanger Tube Vibration Data Bank [3]. With this heat exchanger, vibrational damage has been proven to be due to cutting of the tubes over the baffles. The last part outlines the possibilities and limits of further work.

This thesis is focused on vibration and noise diagnostics of a combustion engine. In the range of the current knowledge there is an analysis of measuring devices, units of measure, possibilities of frequency analysis and a combustion engine from the point of view of vibrations and noise. Part of this work is creating a technical experiment where there were measured both vibrations and noise of two combustion engines. From the data it was done a frequency analysis. Conclusion of the analysis is an evaluation of frequencies which occurred on given engines.

The Diploma thesis deals with the testing of electrically assisted turbochargers. Aim of this work is to apply the established way of the performance testing of conventional turbochargers for electrically assisted turbocharger. Part of this work is to create a program for the calculation of the observed characteristics of the turbocharger. The program is extended to the characteristics of the generator for electrically assisted turbocharger. The program will serve as a basic for control the data for tested motorsport applications.