This thesis deals with the effect of frequency inverter on the lifetime of roller bearings. The measurement has been carried out on the frequency inverter and induction motor by Siemens in the Switchgear laboratory of Fakulty of elektrical engineering and communication. Data has been recorded and processed on Adash VA4 Pro analyzer. Methods of measuring RMS values and frequency analysis of vibration and current were used for the analysis. Based on the mutual similarity of frequency spectrum, the presence of the high frequency capacitive current in the bearings has been proven. To prevent this, possible solutions have been presented. In the second part of the experiment an effect of changing pulse width modulation (PWM) on vibration was examined. The goal was to make a basic analysis and to provide background material for further research.

This diploma thesis deals with the analysis and design optimization of a speaker cabinet (enclosure) produced by the additive technology of 3D sand printing. The introductory part is devoted to the theory, both in the field of noise, vibration and the method of their calculations, as well as the theory of speakers and their systems. Numerical and experimental modal analysis is performed, which were compared to determine the mechanical properties of the new material, including material damping. This is followed by experimental and numerical harmonic analysis, with output in the form of a numerical model describing the behaviour of the structure during its excitation. The data are compared with a modal analysis of the internal acoustic space and the critical shapes and their frequencies are determined. At the end of the work, construction modifications are proposed to increase the rigidity of enclosures, the influence of which is evaluated on the created numerical models.

In one of the first hours of study at the Institute of Mechanics of Bodies, Mechatronics and Biomechanics, the author of this work received three basic recommendations regarding measurement: 1) Do not measure! 2) If you measure, do not repeat the measurement!! 3) If you repeat the measurement, do not compare the measurements!!! However, this thesis boldly violates all three recommendations. In the introductory theoretical part, it briefly introduces the vibration of multi-degree of freedom damped systems and describes experimental ways of determining the modal damping. It also summarizes the Operational Modal Analysis (OMA) approach, explains the principle of the FDD method, and introduces EFDD (Enhanced Frequency Domain Decomposition) method which allows to determine not only natural frequencies and shapes as FDD does, but also modal damping of the shapes. A script in Matlab environment for processing vibrations using EFDD method is one of the thesis outputs. The script is first tested by computational model, where a model system with known damping is tested and damping is determined by the script. Subsequently, the work moves to the actual measurement of the real system - a bonded bar which is analysed by Experimental Modal Analysis and OMA, while the second variant uses commercial EFDD method (Brüel a Kjr company) and programmed script. In the conclusion of the thesis the damping results are compared to each other. The diploma thesis continues in Ing. M. Pop’s thesis – Modal Analysis Experimental Method Verification. From this work a part of measured data is taken. Specific cases of data use are always listed in the appropriate section of the text.

This master's thesis deals with data processing for an electrodynamic test bench. The thesis presents a theoretical overview of signal distribution, determination of fatigue damage from random vibrations and a description of test benches. The next part deals with setting up the test time reduction in GlyphWorks software. The aim of this thesis is to process and create a procedure for an accelerated fatigue test from data measured during an operational test on a polygon. The data are then verified on an electrodynamic test rig using a Skoda Auto dynamic test room. The final part of the thesis contains data evaluation and a guide explaining how to easily create a test in the relevant software.

This master’s thesis is focused on the compilation of a computational modelling of gear mesh engagement dynamics of a spur gear by MBS approach. The user input is the specific geometry of gears, the operating speed, and the load torque. The output are the forces in the gear engagement and the reaction of the forces in the wheel bearings depending on the change in the stiffness of the gear due to the changing number of teeth in the engagement and the change in the axial distance. This model is characterized by a fast and relatively accurate calculation in the time domain. This means that it can react to changes in parameters during simulation such as axial distance, speed, and torque.

This master´s thesis deals with problem of reliability of technical device in general a so there is explained bathtub curve, defects and malfunctions of devices and then there is a brief outline of reliability system. This thesis further briefly describes technical diagnostic and then there is performed the vibrodiagnostic measurements of selected pumps and ventilators in in heating plant Červený mlýn in Brno. Evaluation of their condition is done according to relevant standards. Further there was done a diagnostic of the steam traps through the ultrasound diagnostic. The last part of my thesis deals with the reliability of selected specific pumps in foregoing rating plant. There are showed reliability curves of selected pumps and elaboration of data from their long-term vibrations measurement.

The aim of this master´s thesis is to introduce methods of diagnostics of vibrations in electrical machines. Describe the various vibration sources located inside and outside of the electric machine. Description of the sources of vibration is then preferably dedicated to vibration of electromagnetic origin. There is a description of the construction of an asynchronous motor and the magnetic circuit, the theory of vibrations and their origin. Described are also vibration sensor enables measurement and mathematical tools for their evaluation. In this work also practical vibration measurements on an asynchronous motor, data processing, their subsequent analysis and computer simulation of electromagnetic vibration origin. The conclusion of this work is devoted to the evaluation of the data obtained.

This diploma thesis is focused on operational testing of selected railway lines with different structures of railway superstructure. For the purposes of measuring were chosen suitable measuring sections on the rail corridor and was designed suitable measuring methodology. Dynamic and acoustic parameters of tested structures were determined on the basis of all tests, which were performed. Suitable mathematic method was chosen for evaluation of tests in time and frequency zone. Part of my work is also compare parameters of the tested structures and recommendations for practice.

This thesis "Silicone damper of a six-cylinder in-line diesel engine " is focused on the proposal of alternative using of silicone damper for the a six-cylinder in-line diesel engine, which is made for tractors and other industrial aplications. The aim of this thesis is to count the oscilation of crankshaft by the help of appropriate dynamic model, then to propose such a basic parameters of silicone damper, which absorbes torsion blip crankshaft to acceptable value. The next part of my thesis is proposal of the constructive implementation of fixation the silicone damper on the free part of crankshaft. The last part of my thesis is comparing and evaluating the oscilation of crankshaft without a dumper and with a new propsal of the silicone damper.

This thesis deals with modifications to the construction of vibration-to-electricity energy converter, which is one of possible solutions to problem of sustainable and stable energy source for wireless sensor supply. Upon the exploration of the present state of this problem, new construction of generator is proposed. The aim of this proposal is to enhance the existing generator properties with respect to retention of its dimensions and its weight. Results obtained by simulations of model with proposed parameters are presented and analysed.