Increasing population across the globe paved the way for rapid growth in industrialization. Pharmaceuticals, automotive, textiles, agriculture, electronics, electrical and many other industries discharge different types of heavy metals, dyes and organic contaminants into ground water. These discharges are released into lakes and rivers without prior treatment causing huge environmental impact to the environment. Among different remediation techniques, adsorption was considered the most promising method because of its low-cost and high efficiency. Biomass is considered as the most practical and renewable source for production of bio products and biofuels. Biomass is also used for carbon sequestration and as an essential element to produce hydrochar and biochar which are considered as the 21st century black gold. Hydrochar and biochar can be used as an excellent low-cost adsorbent for the removal of heavy metals, dyes and organic contaminants from water. This dissertation work focuses on, firstly, development of novel oxone treated hydrochar as an adsorbent for the efficient removal of Pb(II) and Methylene Blue (MB) from aqueous solutions. Secondly, preparing novel ozone oxidized hydrochar treated with polyethyleneimine for removal of Remzol Brilliant Blue (RBB) and Remzol Reactive Black (RRB) dyes from aqueous solutions. Thirdly, producing high-performance CO2 activated biochar as an adsorbent for efficient removal of Aniline from aqueous solution. All prepared hydrochar and biochar adsorbents were characterized by SEM, TGA, FTIR, Elemental analysis, conductometric titration, and N2 adsorption-desorption isothermal analyses (BET and BJH). The adsorption capacities were determined by Atomic absorption spectrometry (AAS) and Ultraviolet–visible spectroscopy (UV-VIS) respectively. The adsorption capacity of each prepared biochar or hydrochar was determined and both kinetic and isothermal studies were performed. The optimal preparation conditions and adsorption parameters were determined for each adsorbent.

As a result of the EPA?s Disinfection Byproduct Rule, the Northeast Mississippi Regional Water Supply District requested that the Environmental Technology and Applications Laboratory at Mississippi State University conduct a study to develop techniques to comply with new TOC regulations. This study involved the use of jar testing and Enhanced Coagulation in a laboratory setting over a period of twelve months to optimize the various coagulants evaluated in this study. Iron (III) sulfate, aluminum sulfate, aluminum chloride, aluminum chlorohydrate, and a number of polyaluminum chlorides were evaluated in this study. Coagulants were evaluated on both a treatment effectiveness and economical basis. It was determined that an acidified alum solution performed best at meeting EPA standards for total organic carbon reduction, as well as being economically feasible.

No description available.

No description available.

No description available.

Nitrogen is an essential nutrient for plant and animal life; however, its presence in concentrations exceeding assimilative capacities of receiving water bodies is undesirable. Therefore, the form and concentration of total nitrogen released in wastewater effluents is of great concern. During the course of this study, the nitrogen analysis was performed on the various unit processes of the Florida Technological University wastewater treatment plant. The average percent removal of nitrogen between plant influent and clarifier effluent was 30.5% during the month of August 1975. It is believed that the nitrogen removal is attributed to luxury uptake by the biomass through the plant. The clarifier effluent was highly nitrified containing an average ammonia nitrogen concentration of 0.76 milligrams per liter and a nitrate nitrogen concentration of 16.47 milligrams per liter. The extent to which nitrification took place was 93 - 98% with an average of 96.5% for the month of August.

There are many reports indicating the presence of various emerging contaminants (ECs) in treated wastewater and other water sources. The detection of such contaminants in the environment and the ability of these contaminants to pose potential threats to the environment at very low concentrations have led to a need for more efficient treatment technologies. Cyclodextrins (CDs) have gained significant interest as an alternative adsorbent for water and wastewater treatment because of their unique physico-chemical characteristics and excellent selectivity towards organic compounds. The property of CD to form inclusion complexes with various molecules through host-guest interactions has made it a useful compound for the removal of a number of contaminants from water and wastewater. The overall goal of the study is to identify and develop a novel adsorbent for the removal of ECs of interest. The specific objectives are a) to synthesize various beta-cyclodextrin (BCD) based adsorbents by coating BCD onto different supports such as silica, filter paper, iron oxide, and zeolite, b) to perform batch and column experiments using the developed adsorbents, c) to evaluate the performance of the adsorbents in different water matrices such as MQ water, simulated wastewater in presence of humic acid, and real municipal wastewater, d) to study the regeneration potential of the adsorbents. In this research, various (BCD) based hybrid adsorbents were synthesized and their performances were evaluated based on the removal of selected ECs. At first, chemically bonded BCD onto silica particles as hybrid adsorbents were synthesized by using crosslinking agents and copolymers. Three different methods were used to synthesize 14 different BCD coated silica adsorbents. The adsorbent prepared by reacting BCD with hexamethylene diisocyanate (HMDI) as crosslinking agent and dimethyl sulfoxide (DMSO) as solvent showed best results in removing the ECs studied. The adsorbent showed more than 95% removal of 17β-estradiol (in single component) and more than 90% of most of the estrogens (mixture of 12), more than 99% of perfluorooctanoic acid (PFOA) (in single component) and more than 90% of most of the PFCs (mixture of 10), and a maximum of 90% removal in case of BPA. The adsorption capacity of the developed adsorbent was observed to be higher for the removal of 17β-estradiol and PFOA than that of commercially available activated carbon (F400) in MQ water. In order to represent the real environmental scenario, further batch experiments were conducted for the removal of two PFCs (PFOA and PFOS (perfluorooctane sulfonic acid)), 17β-estradiol, and BPA at environmentally relevant concentrations from wastewater. The adsorbent was effective in removing the ECs that were spiked in the secondary effluent of a municipal wastewater treatment plant. Furthermore, the adsorbent was successfully regenerated with methanol over four cycles without significant loss in its adsorption capacity for the removal of PFOA and estrogens. Ozonation as an alternative method of regeneration was also used and the process was also very effective in regenerating the adsorbent over seven successive cycles for the removal of BPA and 17β-estradiol. The characterization of the adsorbents using FTIR, TGA, and TEM confirmed the coating of BCD onto silica particles. The TGA results showed high thermal stability of the adsorbent (upto 300oC). As an alternative to chemical impregnation, another method of synthesis was developed where various BCD based hybrid adsorbents were synthesized by physically impregnating hydroxypropyl BCD (hpBCD) polymer onto three different supports: iron oxides, zeolite, and filter paper. The hpBCD impregnated filter papers were synthesized by solvent evaporation method and different adsorbents were synthesized by varying the polymer loadings. The polymer loading was optimized based on the performance of the modified (polymer impregnated) filter paper in terms of its filtration capacity as well as adsorption capacity to remove PFOA and BPA. The magnetic adsorbent was prepared by mixing hpBCD polymer with iron oxide (Fe3O4) particles. It was observed that by increasing the mixing time of the support (Fe3O4) with the polymer from 48 to 96 hr, the adsorption capacity of the adsorbent (hpBCD polymer coated Fe3O4) could be significantly enhanced. The same approach was also used to synthesize hpBCD polymer coated zeolite adsorbent and both adsorbents (hpBCD/zeolite and hpBCD/Fe3O4) were effective in removing the selected ECs from MQ water, simulated water, and wastewater. / Civil Engineering

No description available.

No / A new technique using ozone loaded on adsorbents for industrial waste-water treatment has been investigated. This is a three-step process: ozone adsorption on a fixed bed column; water treatment on the bed loaded with ozone; and finally drying/ regeneration of the wet bed. Silica gel of mean particle size of 1.5 mm has been tested for ozone loading capacities followed by water treatment, both at ambient temperature. The mechanisms of the mass transfer process during ozone loading and water treatment have been established. The drying of the adsorbent using vacuum and dry air is feasible, but it is a time-consuming operation. A design procedure is described for the whole system.

Gas bubbles that form within water treatment plants can disrupt drinking water treatment processes. Bubbles may form whenever the total dissolved gas pressure exceeds the local solution pressure, a condition termed dissolved gas "supersaturation." This project investigated how bubble formation affects conventional drinking water treatment and examined factors that can reduce these problems. Gas bubbles attached to coagulated floc particles can reduce settling efficiency and create "floating floc." In laboratory experiments, bubbles formed on the surface of the mixing paddle, since this was the location of minimum pressure within the system. The formation and stability of floating floc was dependent on many different factors including the amount and type of dissolved gas supersaturation and surface chemistry of the mixing paddle. The intensity and duration of rapid mixing also controlled the amount of floating floc. Bubbles forming in filter media can block pore spaces and create headloss, a process popularly termed "air binding." During benchscale filtration experiments, bubbles were released upwards from the media in a burping phenomenon, and bubbles could also be pushed downwards by fluid flow. Burping is beneficial since it partly alleviates the bubble induced headloss, but the media disruptions might also decrease filter efficiency (particle capture). Bubble formation within filters can be reduced by increasing the pressure inside the filter via greater submergence (water head above the media), lower hydraulic flow rate, or use of a more porous media. The mode of filter operation (declining or constant flow rate) will also affect the local filter pressure profile. Dissolved gas supersaturation and bubble formation are detected in on-line turbidity devices and particle counters causing spurious measurements. The use of bubble traps usually reduced these problems, but one device worsened turbidity spikes. Flow disturbances may also release bubbles upstream of the on-line turbidimeter, which can cause spikes in turbidity readings. / Ph. D.