1 |
A wave energy converter for ODAS buoys (WECO)Fiander, David 29 January 2018 (has links)
Ocean Data Acquisition System (ODAS) buoys are deployed in many seas around the world, a subset of these are wave monitoring buoys. Most are powered by solar panels. Many of these buoys are subjected to movement from waves, and could benefit from a wave energy converter specifically designed for ODAS buoys (WECO). A particular buoy that could benefit from this technology is the TriAXYS wave buoy [1]. This thesis discusses the development of a self-contained WECO that would replace one of the buoys four on board batteries, and harvest energy from the buoy motion to charge the remaining three batteries. A major constraint on the WECO is that it can’t affect buoy motion and jeopardize wave data that is derived from the motion.
Rather than follow a traditional approach to simulating the motion of the buoy / WECO system, using hydrodynamic modelling and theoretical wave profiles, existing motion data from a buoy installation was analyzed to find the loads that were applied to the buoy to cause the motion. The complete set of mass properties of the TriAXYS buoy were derived from the 3D model provided by AXYS Technologies. These mass properties were compared to the linear and rotational accelerations to find the loads that were applied at the buoy center of gravity (CG) to cause the recorded motion.
An installation off the coast of Ucluelet, BC was selected for this investigation because it is subjected to open ocean swells, and data from the winter months of November to March of 2014 to 2016 is available. Winter data was used since there is more wave action to power the WECO during the winter months, and there is sufficient solar irradiation to power the buoy in summer months. Accurate buoy motion data at a 4 Hz sampling rate was available from three rotational rate gyros and three linear accelerometers installed in the buoy. Each dataset of samples represented a 20 minute window that was recorded once every hour.
Five conceptual WECO designs were developed, each of which focused on the extraction of power from a different degree of freedom (DOF) of buoy motion (surge, sway, heave, roll, and
iv
pitch). Three designs used a sliding (linear) oscillating mass, and one was aligned with each of the surge, sway, and heave axis of the buoy. Two designs used a rotating oscillating mass, and the axis of rotation of each device was aligned with either the roll or pitch axis of the buoy.
All proposed WECO configurations were modeled as articulated mass, spring, and damper systems in MATLAB using the Lagrange method. Each WECO/buoy assembly formed an articulated body. Mass properties for each configuration were derived from the 3D models. The equations of motion for the original buoy no longer applied, but the environmental forces applied to the hull would still be valid as long as the WECO didn’t alter motion significantly.
The power take off (PTO) was modeled following standard convention as a viscous dashpot. The damping effect of the dashpot was included in the models using Rayleigh’s dissipation function that estimated the energy dissipated by the PTO.
A subset of load datasets was selected for evaluating the maximum power potential of each WECO. Each WECO was tuned to each dataset of loads using the spring rate, and the damping coefficient was optimized to find the maximum power while avoiding end stop collisions. A second subset of data was selected to evaluate the average power that would be generated throughout the winter months for the two most promising designs. This evaluation was performed for static spring and damping coefficients, and the coefficients that resulted in the highest power output were discovered.
The motion of the WECO oscillating mass with respect to the buoy was used in conjunction with the damping ratio to form an estimate of the ideal (i.e. with no mechanical or electrical losses) power generation potential of each WECO configuration during the winter months. The two leading WECO designs both had sliding (linear) oscillating masses, one was aligned with the surge axis and produced theoretical average of just over 0.5 W, the other was aligned with the heave axis and produced theoretical average of just under 0.5 W. / Graduate
|
2 |
Wave Energy Converter Performance Modeling and Cost of Electricity AssessmentJarocki, Dmitri 01 April 2010 (has links)
California is experiencing a rapid increase in interest for the potential of converting ocean waves into clean electricity. Numerous applications have been submitted for the permitting of such renewable energy projects; however the profitability, practicability, and survivability have yet to be proven. Wave energy conversion technology has steadily matured since its naissance in the 1970’s, several wave energy power installations currently exist, and numerous plans for commercial power plant are in the works on the shores of multiple continents. This study aims to assess the economic viability of two proposed commercial wave energy power plant projects on the Central California Coast. A theoretical 25 MW capacity wave energy plant located at a site five nautical miles off of Point Arguello, in Santa Barbara County is compared to a site five nautical miles off of Morro Bay, in the County of San Luis Obispo. The Pacific Gas and Electric Company and Green Wave Energy Solutions, LLC have proposed full-scale commercial wave power plants at these sites, and are currently undergoing the federal permitting processes. Historical wave resource statistics from 1980 to 2001 are analyzed with performance specifications for the AquaBuOY, Pelamis P1, and WaveDragon wave energy converters (WECs) to calculate the annual electrical output of each device at each site. Sophisticated computer modeling of the bathymetric influence on the wave resource at each site is presented using the program Simulating Waves Nearshore (SWAN) developed by the Delft University of Technology. The wave energy flux, significant wave height, and peak period are computed at each site for typical summer and winter swell cases, using seafloor depth measurements at a 90 meter rectangular grid resolution. The economic viability of commercial electricity generation is evaluated for each WEC at each site by the calculation of the net present value of an estimated 25-year project life-cycle, the internal rate of return, and the required cost of electricity for a 10-year project simple payback period. The lowest required price of electricity is $0.13/kWh and occurs at the Point Arguello site using the AquaBuOY WEC. The highest annual capacity factor is 18% using the Pelamis WEC. The net present value and internal rate of return calculations suggest that the AquaBuOY WEC is profitable at both sites for electricity prices above $0.14/kWh. Shallow water wave propagation SWAN modeling demonstrated favorable wave energy flux states for WEC operation and power generation at both sites, with typical winter energy fluxes of 30-37 kW/m.
|
3 |
Self-Reacting Point Absorber Wave Energy ConvertersBeatty, Scott J. 31 August 2015 (has links)
A comprehensive set of experimental and numerical comparisons of the performance of two self-reacting point absorber wave energy converter (WEC) designs is undertaken in typical operating conditions. The designs are either currently, or have recently been, under development for commercialization. The experiments consist of a series of 1:25 scale model tests to quantify hydrodynamic parameters, motion dynamics, and power conversion. Each WEC is given a uniquely optimized power take off damping level. For hydrodynamic parameter identification, an optimization based method to simultaneously extract Morison drag and Coulomb friction coefficients from decay tests of under-damped, floating bodies is developed. The physical model features a re-configurable reacting body shape, a feedback controlled power take-off, a heave motion constraint system, and a mooring apparatus. A theoretical upper bound on power conversion for single body WECs, called Budal's upper bound, is extended to two body WECs.
The numerical analyses are done in three phases. In the first phase, the WECs are constrained to heave motion and subjected to monochromatic waves. Quantitative comparisons are made of the WEC designs in terms of heave motion dynamics and power conversion with reference to theoretical upper bounds. Design implications of a reactive power take-off control scheme and relative motion constraints on the wave energy converters are investigated using an experimentally validated, frequency domain, numerical dynamics model. In the second phase, the WECs are constrained to heave motion and subjected to panchromatic waves. A time domain numerical model, validated by the experimental results, is used to compare the WECs in terms of power matrices, capture width matrices, and mean annual energy production. Results indicate that the second WEC design can convert 30% more energy, on average, than the first design given the conditions at a representative location near the West coast of Vancouver Island, British Columbia, Canada. In the last phase, the WECs are held with three legged, horizontal, moorings and subjected to monochromatic waves. Numerical simulations using panelized body geometries for calculations of Froude-Krylov, Morison drag, and hydrostatic loads are developed in ProteusDS. The simulation results---mechanical power, mooring forces, and dynamic motions---are compared to model test results. The moored WEC designs exhibit power conversion consistent with heave motion constrained results in some wave conditions. However, large pitch and roll motions severely degrade the power conversion of each WEC at wave frequencies equal to twice the pitch natural frequency. Using simulations, vertical stabilizing strakes, attached to the reacting bodies of the WECs are shown to increase the average power conversion up to 190% compared to the average power conversion of the WECs without strakes. / Graduate / scottb@uvic.ca
|
4 |
Underwater radiated noise from Point Absorbing Wave Energy Converters : Noise Characteristics and Possible Environmental EffectsHaikonen, Kalle January 2014 (has links)
The conversion of wave energy into electrical energy has the potential to become a clean and sustainable form of renewable energy conversion. However, like all forms of energy conversion it will inevitably have an impact on the marine environment, although not in the form of emissions of hazardous substances (gases, oils or chemicals associated with anticorrosion). Possible environmental issues associated with wave energy conversion include electromagnetic fields, alteration of sedimentation and hydrologic regimes and underwater radiated noise. Underwater noise has the potential to propagate over long distances and thus have the potential to disturb marine organisms far away from the noise source. There is great variation in the ability to perceive sound between marine organisms, one sound that is clearly audible to one species can be completely inaudible to another. Thus, to be able to determine potential environmental impact from WECs associated with underwater noise, the noise radiated from the WECs must be known. This thesis presents results from studies on the underwater radiated noise from four different full-scale WECs in the Lysekil Wave Power Project. Hydrophones were used to measure the underwater radiated noise from operating point absorbing linear WECs. The main purpose was to study the radiated noise from the operating WECs with emphasis on characteristics such as spectrum levels, Sound Pressure Level (SPL), noise duration and repetition rate. This to be able to determine the origin of the noise and if possible, implement design changes to minimize radiated noise. The results identified two main operational noises (transients with the bulk of the energy in frequencies <1 kHz). The SPL of the radiated noise fluctuated significantly, depending on wave height. Broadband SPLrms of the measurements ranged between ~110 dB and ~140 dB re 1 µPa and SPLpeak of specific noises ranges between ~140 and ~180 dB re µPa. Audibility was estimated range from 1km to 15 km depending critically on species and on assumptions of propagation loss. The noise is not expected to have any negative effects on behaviour or mask any signals, unless in the vicinity (<150m) of the WECs in significant wave heights. No physical damage, even in close vicinity are expected on either fish or marine mammals. Having the aim to have as little impact on the environment a possible, these studies are important. This way precautions can be implemented early in the technical development of this kind of renewable energy converters. The benefits from the WECs the Lysekil wave power project are believed to outweigh possible environmental impacts due to underwater radiated noise. / <p>Vid avhandlingens tryckläggning upptäcktes inte att tidpunkt för disputation var fel.</p>
|
5 |
An investigation of the wave energy resource on the South African Coast, focusing on the spatial distribution of the South West coastJoubert, J. R. 03 1900 (has links)
Thesis (MScEng (Civil Engineering))--University of Stellenbosch, 2008. / This thesis is an investigation of the wave power resource on the South African coast,
focusing on the spatial distribution of wave power of the coastal region exposed to the
highest wave power. The study’s main objective is to provide a detailed description of the
spatial distribution of wave power to assist in the selection of locations for deployment of
Wave Energy Converter (WEC) units in this zone. The study methodology employed to
achieve this main objective entails an analysis of measured wave data recorded at wave
recording stations distributed along the South African coast. The analysis provided a
general description of wave power at locations for which wave data exist. From this analysis
it was found that the South West Coast is exposed to the highest wave power, with an
average wave power of approximately 40 kW per meter wave crest. The rest of the South
African coast is exposed to average wave power between approximately 18 kW/m to 23
kW/m.
The wave power characteristics on the South West Coast region (from Cape Point to Elands
Bay) were therefore the focus of this thesis. The study objective was achieved by
transferring deep sea wave data into the nearshore South West Coast study area with the
Simulating WAves Nearshore (SWAN) wave model. The deep sea wave data was obtained
from a 10 year period of available hindcast data. A simplified simulation procedure was
required in order to make the study practically feasible. A sensitivity analysis was carried
out to determine the validity of the simplified simulation procedure and it was found that the
procedure slightly overestimate wave power in the shallower water regions due to the
underestimation of energy dissipation processes. This overestimation was deemed
acceptable for the dominant wave conditions and the simplified model was therefore applied
in the study. An appropriate programming system was developed and used to transfer the
available 10 year deep sea wave data into the selected South West Coast region. From this
exercise spatial distribution of wave power and related statistical parameters were obtained
for the study area. The accuracy of the modelled output was investigated by directly
comparing it to wave data recorded during the overlapping recording period. It was found
that the model slightly overestimates the monthly wave power resource compared to the
measured data with a maximum overestimation of 9%; which is sufficiently accurate for the
purpose of the study.
The results of this investigation can be used for the identification of areas of high wave
power concentration within the study area for the location of WEC units. Further numerical modelling is required for the detailed design of wave farms, especially if potential
sites are located in shallow water (shallower than approximately 50 m). / Centre for Renewable and Sustainable Energy Studies
|
6 |
Design and development of a novel wave energy converterJoubert, James Rattray 12 1900 (has links)
Thesis (PhD)--Stellenbosch University, 2013. / ENGLISH ABSTRACT: The design, development and evaluation of a novel wave energy converter (WEC)
device, called the ShoreSWEC, in a South African port development is presented.
Based on the device requirements, site selection criteria were specified and applied
to identify a suitable deployment location. A wave modeling procedure was
developed to determine the operational wave conditions and available wave power
resource at the selected location. The site was found to have a low mean annual
average resource of approximately 2.3 kilowatt per meter wave crest (kW/m) due to
its relatively sheltered location. The wave model was further used to determine
design storm conditions and a structural stability analysis of the device was
conducted.
Experimental tests were performed to evaluate the hydrodynamic conversion
efficiency of a single chamber of the device at its most conservative orientation,
under a variety of wave energy conditions. The effect of a floor incline and an
additional chamber on the performance of the system was investigated. The incline
improved efficiency for low wave heights, making it ideal for the low wave power
resource conditions of the site, whilst the multi-chamber system experienced
increased performance at high wave periods. A comparison between the
ShoreSWEC and a conventional oscillating water column (OWC) WEC showed that
the OWC extracted 72% more energy, highlighting the sensitivity of performance on
device orientation. A three-dimensional (3D) numerical model of the experimental
setup was developed. The numerical model provided comparable water surface
elevations inside the flume and chamber, yet predicted significantly higher internal
chamber pressures and overall efficiency. The electricity generation potential of a 10
chamber ShoreSWEC at the specified location, approximated from the experimental
results and 11 years of hindcast wave data, was found to be 6 kW on average for a
15 kW capacity system.
Results of this study highlighted the need for greater understanding of the
hydrodynamic characteristics of a full length device. Experimental tests in a 3D wave
basin on a scaled full length ShoreSWEC model are therefore recommended. Once
conducted, South Africa will be one step closer to the deployment of the full scale
SWEC device. / AFRIKAANSE OPSOMMING: Die ontwerp, ontwikkeling en evaluasie van ‘n unieke golfenergieomsetter (GEO),
genaamd die ShoreSWEC, in ‘n Suid-Afrikaanse haweontwikkeling word aangebied.
Terrein evaluasie kriteria, gebaseer op die omsettervereistes, is ontwikkel en
toegepas om die mees belowende terrein te identifiseer. ‘n
Golfmodeleringsprosedure is ontwikkel om die operasionele golfkondisies en
beskikbare golfdrywinghulpbron te bepaal. Daar is gevind dat die terrein ‘n lae
gemiddelde golfdrywing van bykans 2.3 kilowat per meter golfkruin het as gevolg
van die beskutte ligging. Die golfmodel is verder gebruik om ontwerpstormkondisies
te bepaal en ‘n stabiliteitsanalise was op die toestel struktuur uitgevoer.
Eksperimentele toetse van verskeie golfenergie kondisies is gedoen om die
hidrodinamiese omsettingseffektiwiteit van ‘n enkel kamer van die toestel te bepaal
teen sy konserwatiefste orientasie. Die effek van ‘n vloerhelling en ‘n addisionele
kamer op die uitsette van die sisteem is ondersoek. Die helling het effektiwiteit
verbeter vir lae golfhoogtes wat dit ideaal maak vir die lae hulpbron by die terrein,
terwyl die veelvoudige-kamer-sisteem beter gevaar het by hoë golfperiodes. ‘n
Vergelyking tussen die ShoreSWEC en ‘n konvensionele ossilerende waterkolom
(OWK) GEO het gewys dat die OWK 72% meer energie onttrek. Dit beklemtoon die
sisteem se sensitiwiteit vir die inkomende golfrigting. ‘n Drie-dimensionele (3D)
numeriese model van die eksperimentele opstelling is ontwikkel. Die numeriese
model het aansienlik hoër drukke binne die kamer, en gevolglik algehele effektiwiteit,
voorspel as die eksperimentele toetse. Die elektriese opwekkingskapasiteit van ‘n 10
kamer ShoreSWEC by die terrein, gebaseer op die eksperimentele resultate en 11
jaar se golfdata, is bereken as 6 kW gemiddeld vir ‘n 15 kW kapasiteit stelsel.
Die bevindinge van hierdie studie het die behoefte aan ‘n beter begrip van die
hidrodinamiese eienskappe van ‘n vollengte sisteem beklemtoon. Eksperimentele
toetse in ‘n 3D golfbak op ‘n geskaleerde vollengte ShoreSWEC model word dus
aanbeveel. Sodra dit voltooi is, sal Suid-Afrika een stap nader wees aan die
ontplooiing van ‘n volskaalse SWEC toestel.
|
7 |
Modelling a Novel Linear Transverse Flux Machine and Designing a Hysteresis Current Controller for Power Factor CorrectionAlhaidari, Ahmed January 2019 (has links)
In this thesis, the basics of electromagnetic theory for wave-energy conversion are reviewed, some of the characteristics of the ocean wave are investigated, some of the power take-off (PTO) systems are introduced, and details about linear permanent magnetic machines, in particular, are discussed. The thesis aims to model the novel linear transverse flux machine designed by Anders Hagnestål and to build hysteresis current controller for power factor correc- tion. Although this machine is expected to have high performance in terms of efficiency, it also exhibits a strong mutual interaction between the three phases of the machine. Thus, simplification of the actual model of the machine is im- posed to mitigate the complexity of the machine and facilitate the Simulink model. Four cases of the double band hysteresis control are studied. The cur- rents seem to be responding properly to the control scheme; however, software and hardware programming of a microprocessor would be preferable to ensurethe applicability of the control strategy in a real environment. / I detta examensarbete undersöks elektromagnetisk teori och havsvågors egenskaper. Några energiomvandlingssystem introduceras och permanentmagnetiserade maskiner diskuteras i detalj. Syftet med avhandlingen är att modelleraen ny linjär transversalflödesmaskin som är designad av Anders Hagnestål och att bygga en hysteresbaserad strömkontroll för denna. Även om maskinen förväntas prestera bra, uppvisar den också en stark ömsesidig magnetisk interaktion mellan de tre faserna. För att kunna hantera detta problem och därmed kunna genomföra simuleringar införs en förenklad elektromagnetisk modell av maskinen. En strömkontroller har implementerats i Simulink, där fyra fall av dubbelbandshystereskontroll studerats. Resultaten från simuleringarna visar att strömkontrollern fungerar. Nästa steg i projektet är att utföra mjukvaru och hårdvaruprogrammering av en mikrokontroller för att testa systemet i enverklig miljö.
|
Page generated in 0.0916 seconds