This thesis describes the development of optical wavelength converters with an integrated coupling structure, fabricated on periodically poled MgO doped lithium niobate (MgO:LN) for optical fiber communication and other all-optical signal processing applications. Wavelength converter is an integral part of any broadband communication system. The ability to transfer information between carrier wavelengths allows for efficient use of the available bandwidth in a transmission medium. Wavelength converters based on PPLN waveguides are among the most efficient nonlinear optical devices available today, due to highspeed operation, low noise, parallel operation on multiple wavelength channels and preservation of information carried in the optical domain. However, low conversion efficiency is an issue for wavelength converter based on PPLN waveguide. Compared to pure LN, MgO doped LN decrease restriction in optical damage and increase conversion efficiency. Integrated coupling structure demonstrates a solution to mode-coupling of the input wave to the fundamental mode of DFG device and increase the conversion efficiency. Therefore, a periodically poled MgO doped lithium niobate (MgO:LN) waveguides with integrated coupling structure is fabricated. The components of integrated coupling structure are compatible with lithium nobate waveguides, including directional couplers, small radius bends, adiabatic taper, and mode filter. The integrated coupling structure combines the pump and signal waves into the DFG conversion section, and makes the single mode conversion of the pump from input waveguide to conversion section. Theoretical models and simulations are provided in this thesis, and performances of the device with this structure are also presented. / Thesis / Master of Applied Science (MASc)

Um Luminescent Solar Concentrators (LSC) é basicamente uma base plástica transparente ou vidro contendo centros luminescentes.Enquanto o recente avanço dos conversores de comprimento de onda tenha aberto novas possibilidades para o desenvolvimento de células solares mais eficientes, estes também abriram novas frentes de pesquisa.Uma destas frentes envolve os problemas encontrados com o uso de novos materiais. Como por exemplo, transferência de energia em polímeros. Surgem propriedades interessantes a respeito dos processos luminescentes ao longo destes sistemas planares.Por estes motivos esses sistemas podem ser aplicados como dispositivos optoeletrônicos, sensores e também em conversores de comprimento de onda. Este estudo descreve a fabricação de guias de onda planares multipoliméricos baseados em uma matrix acrílica (PMMA) dopada com polímeros emissores de luz. A função desta blenda polimérica é absorver um largo espectro de luz e re-emitir ao longo do guia de onda. Os dispositivos foram estudados em termos de suas características de absorção, emissão e excitação.Os polímeros emissores utilizados neste trabalho foram: MEH-PPV, Super Yellow, ADS-108GE, ADS-329BE, e LAPS-16. Estes materiais foram dissolvidos em tolueno e depositados pela técnica casting sobre substratos de vidro contendo filmes metálicos de alumínio.Usando esta configuração, a luz de excitação incidente é acoplada ao guia de onda por absorção e re-emissão através dos polímeros luminescentes. O estudo dos LSCs é realizado por medidas das emissões laterais e normais dos guias. Estes guias apresentam um espectro de emissão com características típicas de uma cavidade do tipo Fabri-Perot, com linhas extremamente estreitas (3 nm) e altamente polarizadas na direção paralela (modo TE) e perpendicular (TM) ao plano do guia de onda.A emissão destes guias é fortemente dependente de sua geometria e do índice de refração efetivo. Os mesmos filmes poliméricos, porém mais espessos (30 m), foram utilizados como conversores de comprimento de onda visando aplicação em conversores solares luminescentes (Luminescence Solar Converters, ou LSCs). O uso de baixas concentrações das moléculas utilizadas foi necessário para evitar possíveis formações de agregados quando altas concentrações de PMMA são utilizadas na preparação dos filmes. A metalização de uma das faces planares possibilitou o aumento da eficiência de conversão dos comprimentos de onda nos LSCs. A luminescência total dos polímeros é completamente convertida em luz de alto comprimento de onda na emissão lateral.Este processo não depende do comprimento de onda de excitação. A metalização de uma das faces planares possibilitou o aumento da eficiência de conversão dos LSCs. Neste sistema, a luz absorvida é convertida em luz de alto comprimento de onda e alta pureza espectral através de processos de reabsorção, relaxação interna e re-emissão que ocorrem ao longo do plano do LSC. A eficiência de conversão e as perdas em função da concentração polimérica na matriz foram estudadas para os LSCs.O escape dos fótons nas interfaces para ângulos menores que o ângulo crítico (c=arcsen(1/n)) e processos de transferência de energia em LSCs com alta concentração polimérica devem ser otimizados para sua aplicação como dispositivos. / Luminescent Solar Concentrators (LSC) are basically composed of a transparent plastic or glass substrate containing luminescent centers.While the recent advance in wavelength converters has opened up many new possibilities for development of more efficient photovoltaic cells, they have also raised new issues. A number of these issues involve problems of dealing with new materials and the understanding of physical process like energy transfer in polymers. Interesting features arise from the luminescent process along these planar systems. Therefore this system can be applied as optoelectronics devices, sensors and also in wavelength converters. This study describes the fabrication of planar multi-polymeric optical waveguides based on acrylic matrix (PMMA) doped with a light emitting polymers. The function of thispolymeric blendis to absorb a broad spectrum of light and re-emit it along the waveguide. The devices were studied in terms of its absorption, emission and excitation characteristics.The emitting polymers used in this research are: poly[2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylenevinylene] (MEH-PPV), Super Yellow, Poly[(9,9-dioctyl-2,7-divinylenefluorenylene)-alt-co-{2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylene}] called ADS108GE, Poly(9,9-dioctylfluorenyl-2,7-diyl) called ADS239BE, and poli-(9,9-n-dihexil-2,7-fluorenodilvinilene-alt-1,4-fenilenovinileno) or Laps16. Films of these materials dissolved in toluene were deposited by casting the polymethacrylate solution on top of a glass substrate containing a reflective aluminum layer. Using this configuration, the incident excitation light is coupled to the wave guide by its absorption and then re-emitted by the luminescent polymers. The LSCs characterization was carried out by measuring the lateral and the normal emissions of the guide. These waveguides show a light emission spectrum with characteristics similar to the Fabri-Perot cavity, where very narrow peaks (3 nm) and highly polarized emission in both TE and TM modes were observed. In addition, the emission is strongly dependent on its geometry and the effective refraction index. In other hand, thicker polymeric guides (30 m) were used as luminescence solar converters (LSCs). The optimal concentration of conjugated polymers solutions has to be very low in order to avoid the formation of aggregates since high PMMA concentrations have to be used in the LSC preparation.The total polymeric luminescence is fully converted to light of high wavelength for the case of lateral emission. This process does not depend on the excitation wavelength. The conversion efficiency was increased by evaporating metals on one planar face of the LSC. In this structure, light is absorbed and then converted to a higher wavelength with high spectral pureness through re-absorption, relaxation and re-emission processes occurring along the LSC plane. The conversion efficiency and the losses along the converter were studied as a function of the polymeric concentration, in order to optimize these structures. A better understanding of the process of energy transfer and photon leakage through the interfaces for angles smaller than the critical angle (c=arcsen(1/n)) is necessary for using LSCs as applied devices.

Um Luminescent Solar Concentrators (LSC) é basicamente uma base plástica transparente ou vidro contendo centros luminescentes.Enquanto o recente avanço dos conversores de comprimento de onda tenha aberto novas possibilidades para o desenvolvimento de células solares mais eficientes, estes também abriram novas frentes de pesquisa.Uma destas frentes envolve os problemas encontrados com o uso de novos materiais. Como por exemplo, transferência de energia em polímeros. Surgem propriedades interessantes a respeito dos processos luminescentes ao longo destes sistemas planares.Por estes motivos esses sistemas podem ser aplicados como dispositivos optoeletrônicos, sensores e também em conversores de comprimento de onda. Este estudo descreve a fabricação de guias de onda planares multipoliméricos baseados em uma matrix acrílica (PMMA) dopada com polímeros emissores de luz. A função desta blenda polimérica é absorver um largo espectro de luz e re-emitir ao longo do guia de onda. Os dispositivos foram estudados em termos de suas características de absorção, emissão e excitação.Os polímeros emissores utilizados neste trabalho foram: MEH-PPV, Super Yellow, ADS-108GE, ADS-329BE, e LAPS-16. Estes materiais foram dissolvidos em tolueno e depositados pela técnica casting sobre substratos de vidro contendo filmes metálicos de alumínio.Usando esta configuração, a luz de excitação incidente é acoplada ao guia de onda por absorção e re-emissão através dos polímeros luminescentes. O estudo dos LSCs é realizado por medidas das emissões laterais e normais dos guias. Estes guias apresentam um espectro de emissão com características típicas de uma cavidade do tipo Fabri-Perot, com linhas extremamente estreitas (3 nm) e altamente polarizadas na direção paralela (modo TE) e perpendicular (TM) ao plano do guia de onda.A emissão destes guias é fortemente dependente de sua geometria e do índice de refração efetivo. Os mesmos filmes poliméricos, porém mais espessos (30 m), foram utilizados como conversores de comprimento de onda visando aplicação em conversores solares luminescentes (Luminescence Solar Converters, ou LSCs). O uso de baixas concentrações das moléculas utilizadas foi necessário para evitar possíveis formações de agregados quando altas concentrações de PMMA são utilizadas na preparação dos filmes. A metalização de uma das faces planares possibilitou o aumento da eficiência de conversão dos comprimentos de onda nos LSCs. A luminescência total dos polímeros é completamente convertida em luz de alto comprimento de onda na emissão lateral.Este processo não depende do comprimento de onda de excitação. A metalização de uma das faces planares possibilitou o aumento da eficiência de conversão dos LSCs. Neste sistema, a luz absorvida é convertida em luz de alto comprimento de onda e alta pureza espectral através de processos de reabsorção, relaxação interna e re-emissão que ocorrem ao longo do plano do LSC. A eficiência de conversão e as perdas em função da concentração polimérica na matriz foram estudadas para os LSCs.O escape dos fótons nas interfaces para ângulos menores que o ângulo crítico (c=arcsen(1/n)) e processos de transferência de energia em LSCs com alta concentração polimérica devem ser otimizados para sua aplicação como dispositivos. / Luminescent Solar Concentrators (LSC) are basically composed of a transparent plastic or glass substrate containing luminescent centers.While the recent advance in wavelength converters has opened up many new possibilities for development of more efficient photovoltaic cells, they have also raised new issues. A number of these issues involve problems of dealing with new materials and the understanding of physical process like energy transfer in polymers. Interesting features arise from the luminescent process along these planar systems. Therefore this system can be applied as optoelectronics devices, sensors and also in wavelength converters. This study describes the fabrication of planar multi-polymeric optical waveguides based on acrylic matrix (PMMA) doped with a light emitting polymers. The function of thispolymeric blendis to absorb a broad spectrum of light and re-emit it along the waveguide. The devices were studied in terms of its absorption, emission and excitation characteristics.The emitting polymers used in this research are: poly[2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylenevinylene] (MEH-PPV), Super Yellow, Poly[(9,9-dioctyl-2,7-divinylenefluorenylene)-alt-co-{2-methoxy-5-(2-ethyl-hexyloxy)-1,4-phenylene}] called ADS108GE, Poly(9,9-dioctylfluorenyl-2,7-diyl) called ADS239BE, and poli-(9,9-n-dihexil-2,7-fluorenodilvinilene-alt-1,4-fenilenovinileno) or Laps16. Films of these materials dissolved in toluene were deposited by casting the polymethacrylate solution on top of a glass substrate containing a reflective aluminum layer. Using this configuration, the incident excitation light is coupled to the wave guide by its absorption and then re-emitted by the luminescent polymers. The LSCs characterization was carried out by measuring the lateral and the normal emissions of the guide. These waveguides show a light emission spectrum with characteristics similar to the Fabri-Perot cavity, where very narrow peaks (3 nm) and highly polarized emission in both TE and TM modes were observed. In addition, the emission is strongly dependent on its geometry and the effective refraction index. In other hand, thicker polymeric guides (30 m) were used as luminescence solar converters (LSCs). The optimal concentration of conjugated polymers solutions has to be very low in order to avoid the formation of aggregates since high PMMA concentrations have to be used in the LSC preparation.The total polymeric luminescence is fully converted to light of high wavelength for the case of lateral emission. This process does not depend on the excitation wavelength. The conversion efficiency was increased by evaporating metals on one planar face of the LSC. In this structure, light is absorbed and then converted to a higher wavelength with high spectral pureness through re-absorption, relaxation and re-emission processes occurring along the LSC plane. The conversion efficiency and the losses along the converter were studied as a function of the polymeric concentration, in order to optimize these structures. A better understanding of the process of energy transfer and photon leakage through the interfaces for angles smaller than the critical angle (c=arcsen(1/n)) is necessary for using LSCs as applied devices.

La croissance continue du trafic Internet implique une augmentation de la consommation d'énergie en raison des nombreuses conversions optique à électronique(OEO) requises par les routeurs et les commutateurs. L'utilisation de réseaux transparents pourraient freiner cette croissance incontrôlée, mais le maintien des données dans le domaine optique a deux conséquences néfastes: une accumulation du bruit et des non-linéarités de l'amplification qui dégrade fortement les performances au niveau de la couche physique. et la contrainte de continuité de longueur d'onde (WCC) reflétant la conservation de la longueur d'onde du signal optique dans les réseaux optiques multiplexés en longueur d'onde (WDM) qui dégradent les performances du réseau, notamment sa probabilité de blocage. Les convertisseurs de longueur d'onde (WC) peuvent pallier la contrainte WCC, mais les seuls dispositifs suffisamment matures disponibles dans le commerce sont les WC basés sur OEO (OEO-WC). Cependant, leur coût augmente avec les débits binaires. D'autre part, des convertisseurs de longueur d'onde tout optique (AO-WC) ont été démontrés dans des laboratoires de recherche, avec toutefois une plage de conversion limitée et une dégradation du signal converti.Dans cette thèse, nous concevons la couche de transmission en utilisant deux ensembles de formats de modulation différents avec des plages de débits différentes; et par conséquent différents modèles d'estimation de performance. Au niveau du réseau, nos analyses montrent que la contribution des WC dépend des demandes de trafic servant à l’ordre dans un scénario de planification du réseau; qu'en utilisant des algorithmes fixed-alternate-routing (FAR) ou least-loaded-routing (LLR) et un algorithme d'affectation de longueur d'onde first-fit (FF), les AO-WCs offrent les mêmes améliorations de performances que les OEO-WC. De plus, nous identifions une plage de conversion et une cascadabilité optimale d’AO-WC qui montre que le LLR nécessite un nombre de conversions par canal inférieur au FAR. / The continuous growth of Internet traffic implies an increased power consumption due to the many optical-to-electronic (OEO) conversions required by routers and switches. Transparent networks could curb this uncontrolled growth, but keeping the data in the optical domain has two adverse consequences: physical layer impairments accumulation which strongly degrades the performance due to amplication noise and non-linearities; and the wavelength continuity constraint (WCC) to keep the opticalsignal's wavelength unchanged in wavelength-division-multiplexed (WDM) optical networks which degrades network blocking performance. Wavelength converters (WCs) can alleviate the WCC constraint, but the only commercially available devices are the OEO-based WCs (OEO-WCs), however, their cost increases with bit-rates. On the other hand, all-optical wavelength converters (AO-WCs) have been demonstrated in research laboratories albeit with a limited conversion range and a performance that degrades converted signal's quality.In this thesis, we design the transmission layer using two different modulation formats sets with different bit-rates ranges; and consequently different performance estimation models. At the network level, our analyses show that WCs' contribution depends on traffic demands serving ordering in the online traffic assumption; that using xed-alternate routing (FAR) or least-loaded routing (LLR) algorithms and first-fit (FF) wavelength assignment algorithm, AO-WCs give the same performance enhancement as OEO-WCs. Moreover, we identify an optimum AO-WC conversion range and cascadability which shows that LLR requires lower number of conversions per channel compared to FAR.