Simulation, optimization, and implementation of a capacitor-loaded wireless power transfer structure at 6.78 MHz for a target transfer distance of one meter are presented. First, an investigation into the operating principles behind a capacitor-loaded coupled loop structure is carried out via simulation. By adjusting the structural design parameters, it is found that an optimal configuration for this structure is coplanar. A prototype constructed using thin 18 AWG wire for the loops and a variable capacitor for tuning is used to verify simulation. To reduce losses in the wire, thick 9 AWG wire is implemented and measured. Thick wire is necessary for high efficiency yet undesirable for planarization. Since current flows only on the surface of the wire, ‘unwrapping’ that portion yields copper strips that reduce loss by increasing only the width. Thus, by replacing thick wires with copper strips, a planarized structure can be obtained that can reduce ohmic losses without sacrificing its form factor. Next, additional advantages of a capacitor-loaded system, which include reduced electric near-field and the possibility of resonant frequency tuning, are investigated. It is shown by simulation that the capacitor-loaded structure is not strongly affected by nearby dielectric materials since the stored electric energy is significantly lower than the stored magnetic energy in air at resonance. Finally, further optimizations of the structure are considered along with the analytical expressions for maximum efficiency. / text

<p>As research in electromagnetics has expanded, it has given rise to the examination of metamaterials, which possess nontrivial electromagnetic material properties such as engineered permittivity and permeability. Aside from their application in the microwave industry, metamaterials have been associated with novel phenomena since their invention, including sub-wavelength focusing in negative refractive index slabs, evanescent wave amplification in negative index media, and invisibility cloaking and its demonstration at microwave frequency with controlled material properties in space.</p><p>Effective medium theory plays a key role in the development and application of metamaterials, simplifying the electromagnetic analysis of complex engineered metamaterial composites. Any metamaterial composite can be treated as a homogeneous or inhomogeneous medium, while every unit structure in the composite is represented by its permittivity and permeability tensor. Hence, studying an electromagnetic wave's interaction with complex composites is equivalent to studying the interaction between the wave and an artificial material.</p><p>This dissertation first examines the application of a magnetic metamaterial lens in wireless power transfer (WPT) technology, which is proposed to enhance the mutual coupling between two magnetic dipoles in the system. I examine and investigate the boundary effect in the finite sized magnetic metamaterial lens using a numerical simulator. I propose to implement an anisotropic and indefinite lens in a WPT system to simplify the lens design and relax the lens dimension requirements. The numerical results agree with the analytical model proposed by Smith et al. in 2011, where lenses are assumed to be infinitely large.</p><p>By manipulating the microwave properties of a magnetic metamaterial, the nonlinear properties come into the scope of this research. I chose split-ring resonators (SRR) loaded with varactors to develop nonlinear metamaterials. Analogous to linear metamaterials, I developed a nonlinear effective medium model to characterize nonlinear processes in microwave nonlinear metamaterials. I proposed both experimental and numerical methods here for the first time to quantify nonlinear metamaterials' effective properties. I experimentally studied three nonlinear processes: power-dependent frequency tuning, second harmonic generation, and three-wave mixing. Analytical results based on the effective medium model agree with the experimental results under the low power excitation assumption and non-depleted pump approximation. To overcome the low power assumption in the effective medium model for nonlinear metamaterials, I introduced general circuit oscillation models for varactor/diode-loaded microwave metamaterial structures, which provides a qualitative prediction of microwave nonlinear metamaterials' responses at relatively high power levels when the effective medium model no longer fits.</p><p>In addition to 1D nonlinear processes, this dissertation also introduces the first 2D microwave nonlinear field mapping apparatus, which is capable of simultaneously capturing both the magnitude and phase of generated harmonic signals from nonlinear metamaterial mediums. I designed a C-band varactor loaded SRR that is matched to the frequency and space limitation of the 2D mapper. The nonlinear field generation and scattering properties from both a single nonlinear element and a nonlinear metamaterial medium composite are experimentally captured in this 2D mapper, and the results qualitatively agree with numerical results based on the effective medium model.</p> / Dissertation

The emergence of microwave energy harvesting systems, commonly referred to as rectenna or Wireless Power Transfer (WPT) systems, has enabled numerous applications in many areas since their primary goal is to recycle the ambient microwave energy. In such systems, microstrip antennas are used as the main source for collecting the electromagnetic energy. In this work, a novel collector based on metamaterial particles, in what is known as a Split Ring Resonator (SRR), to harvest electromagnetic energy is presented. Such collectors are much smaller in size and more efficient than existing collectors (antennas). A feasibility study of SRRs to harvest electromagnetic energy is conducted using a full wave simulator (HFSS). To prove the concept, a 5.8 GHz SRR is designed and fabricated and then tested using a power source, an Infiniium oscilloscope and a commercially available patch antenna array. When excited by a plane wave with an H-field normal to the structure, a voltage build up of 611 mV is measured across a surface mount resistive load inserted in the gap of a single loop SRR. In addition, a new efficiency concept is introduced, taking into account the microwave-to-AC conversion efficiency which is missing from earlier work. Finally, a 9X9 SRR array is compared with a 2X2 patch antenna array, both placed in a fixed footprint. The simulation results show that the array of SRRs can harvest electromagnetic energy more efficiently and over a wider bandwidth range.

The agricultural sector is an emerging application area for Wireless Sensor Networks (WSNs). This requires sensor nodes to be deployed in the outdoor environment so as to monitor pertinent natural features, such as soil condition or pest infestation. Limited energy supply and subsequent battery replacement are common issues for these agricultural sensor nodes. One possible solution is to use energy harvesting, where the ambient energy is extracted and converted into usable electrical form to energise the wireless sensors. The work presented in this thesis investigates the feasibility of using Radio Frequency (RF) energy harvesting for a specific application; that is powering a generic class of wireless ground-level, agricultural sensor networks operating in an outdoor environment. The investigation was primarily undertaken through a literature study of the subject. The first part of the thesis examines several energy harvesting/ wireless energy transfer techniques, which may be applicable to power the targeted agricultural WSN nodes. The key advantages and limitations of each technique are identified, and the rationale is being given for selecting far-field RF energy harvesting as the investigated technique. It is then followed by a theoretical-based system analysis, which seeks to identify all relevant design parameters, and to quantify their impact on the system performance. An RF link budget analysis was also included to examine the feasibility of using RF energy harvesting to power an exemplar WSN node - Zyrox2 Bait Station. The second part of the thesis focuses on the design of two energy harvesting antennas. The first design is an air-substrate-based folded shorted patch antenna (FSPA) with a solid ground plane, while the second design is a similar FSPA structure with four pairs of slot embedded into its ground plane. Both antennas were simulated, fabricated and tested inside an anechoic chamber, and in their actual operating environment - an outdoor field. In addition, a power harvester circuit, built using the commercially available off-the-shelf components, was tested in the laboratory using an RF signal generator source. The results from both the laboratory and field trial were analysed. The measurement techniques used were reviewed, along with some comments on how to improve them. Further work on the RF energy harvester, particularly on the improvement of the antenna design must be carried out before the feasibility and viable implementations for this application can be definitively ascertained.

Wireless power transfer (WPT) is currently the most efficient way for transmission of power from one port to another, that is popularly used in various applications.This technique can change the previous energy utilization methods in various applications such as electronic devices, implanted medical devices, electrical vehicles and so forth.It mainly helps overcome the limitations of short battery life, limited storage, heavy weight, and high cost of batteries.This paper is based on the design of a transmitter and a receiver to achieve wireless power transfer for applications like optogenetic stimulation in rodents. With inductive coupling, a very high efficiency can be achieved between the transmitting and receiving coils of an antenna at small distances. When the transmitter and receiver are strongly coupled and are working at their resonant frequencies, the range of efficient WPT can be extended. In this work, the simulations are performed in HFSS at a resonating frequency of 13.56 MHz.A 4-port transmitter and a single-port planar receiver model are developed in HFSS, and the simulations are performed to graph the S parameters with a separation distance of 4cm. A Wilkinson power divider is designed using ADS to split the power from the four ports of the transmitter. The design is simulated to compare the S21 at different positions on the TX.

Wireless power transfer is becoming relevant today because of its effectiveness and convenience. It has been employed into consumer electronics such as cellular charging and electric vehicle charging. In general, inductive wireless power transfer (IPT) is mostly used for WPT. IPT requires coils and power transfer enhancing material such as ferrite to transfer power. However, Capacitive wireless Power Transfer (CPT) appears as an alternative because it requires cost effective and light metal plate couplers. Among CPT couplers, Vertical (stacked) Four-Plate Coupler (V4PC) structure offers the advantage of higher input and output self-capacitances, rotational misalignment. Safety is one of the most important aspect of wireless power transfer. This thesis proposes a solution to minimize the leakage electric field of Vertical 4-Plate Couplers (V4PCs). It does so by finding the optimum value of circuit parameters. The effectiveness of the proposed solution is shown by experimental results.

Wireless charging of the EVs offers a convenient, reliable, and automatic charging of the autonomous vehicles without user interference. The focus of this thesis is the design and optimization of new structures for stationary EV wireless charging applications. The fundamentals of the Wireless Power Transfer (WPT) system and its main components including the magnetic couplers, transmitter and receiver power converters, and control methods are studied in depth. The requirements of the EV wireless charging application and design criteria are discussed in detail. The advantages and disadvantages of each topology are highlighted, and possible candidates for EV wireless charging applications are selected. Optimization of the resonant networks in terms of maximum efficiency and misalignment tolerance is studied. Different resonant topologies are studied in detail and their sensitivity functions are extracted. For each topology, an efficiency model is presented that includes the inverter, resonant capacitors, resonant inductor, diode-bridge, and core and conduction losses. Each topology is optimized with two different objective functions and the results are compared through the simulation and experiments. According to the optimization results, suitable topologies for the EV wireless charging application are selected. In order to increase the power density of the wireless charging system, and save ferrite material, integrated inductors into the magnetic couplers are proposed. In this structure, the DC-DC inductor is integrated into the receiver main coil and the resonant inductor is integrated into the transmitter coil. This integration introduces new challenges to the design of the resonant network and magnetic coupler due to the unwanted cross-coupling effect. To address this issue, the fully integrated magnetic structure is optimally designed to have minimum cross-coupling. Moreover, the resonant network is designed based on an optimization problem that includes the cross-coupling into the system equations to ensure maximum efficiency. The proposed fully-integrated magnetic structure is built and experimental tests are presented to validate the performance of the proposed magnetic structure and its optimization method. To reduce the implementation cost, size and weight a PCB-based magnetic coupler is proposed to replace the Litz wire in the magnetic coupler of the WPT system. Moreover, the proposed PCB-magnetic coupler increases the repeatability of the design and reduces manufacturing errors. The PCB-based magnetic coupler is studied through Finite Element Analysis (FEA) to minimize the AC resistance of the coil. Different parameters such including the number of the PCB layers, copper cross-section, and layer thickness are studied in detail to evaluate their effect on the coil resistance. Thermal analysis is performed to ensure the feasibility of the design under different loading conditions. A 3.3 kW/85 kHz wireless charging system is built and experimental tests are presented. A novel modular resonant topology for fast wireless charging is proposed. A modular structure offers reliability, scalability, and better thermal management. The proposed topology is made by multi-parallel inverter legs connected to an LCC resonant network. The outputs of the resonant networks are connected in parallel to feed the transmitter coil with a high excitation current. The proposed modular system is compared with a conventional system and it showed superior performance in different aspects. / Thesis / Doctor of Philosophy (PhD)

Nikolai Tesla's revolutionary experiments demonstrated the possible benefits of transmitting power wirelessly as early as 1891. Applications for the military, consumers, emergency personnel, remote sensors, and others use Tesla’s discovery of wireless power. Wireless power transmission (WPT) has the potential to be a common source of consumable energy, but it will only receive serious consideration if the transmit and receive systems are extremely efficient and capable of delivering usable amounts of power. Research has been conducted to improve the efficiency and performance of nearly every aspect of WPT systems, but the relatively new field of metamaterials (MTMs) has yet to play a dominate role in improving system performance. A gradient index (GRIN) MTM lens was designed using Ansoft’s High Frequency Structure Simulator (HFSS) to improve antenna gain and thereby increase WPT system performance. A simple WPT demonstration system using microstrip patch antennas (MPAs) confirmed the benefits of the GRIN MTM lens. The WPT demonstration system, MPAs, and GRIN MTM lens were constructed and experimentally tested near 2.45 GHz. The theoretical and experimental gain improvement of the MPA due to the GRIN MTM lens is 5.91 dB and 7.06 dB, respectively.

京都大学 / 新制・課程博士 / 博士(工学) / 甲第24232号 / 工博第5060号 / 新制||工||1790(附属図書館) / 京都大学大学院工学研究科電気工学専攻 / (主査)教授 篠原 真毅, 教授 小嶋 浩嗣, 教授 山本 衛 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

No description available.