Catalisadores baseados em óxidos de cério (CeOx, 3/2≤ x ≤ 2) como suporte são utilizados em várias reações de alto interesse econômico, por exemplo as reações de catalizadores de três-vias. Sabe-se que é possível melhorar as propriedade catalíticas da céria, através da mistura com óxido de zircônio e com a adição de partículas metálicas na superfície do material. Entretanto, a deposição de átomos de Zr sobre CeO2(111) é pouco explorada apesar de já ter sido utilizada para a síntese de nanopartículas de Ag de tamanho controlado. Uma das particularidades dos sistemas Zr/CeO2(111) é formar ilhas altura entre 1,5 e 3,0 Å sobre a superfície da céria que são sugeridas na literatura com camadas de Zr-O e O-Zr-O. Entretanto, a natureza e magnitudes das interações entre Zr e CeO2(111) ainda não são totalmente conhecidas, bem como as modificações causadas pelo Zr na superfície de CeO2 e os mecanismos que controlam a oxidação do Zr e a formação de ZrO2 na superfície. Visando entender as interações Zr/CeO2(111) e a formação de ZrO2 sobre CeO2(111), realizou-se um estudo teórico da adsorção de n (1 ≤n ≤ 4) adatomos de Zr sobre CeO2(111), e da formação de ZrO2 sobre CeO2(111). As análises de carga indicam transferências de carga do adatomos de Zr para a superfície e mudança no estado de oxidação das espécies. Os Zr se oxidam á Zr4+ e interagem com O2- da superfície, onde quatro cátions Ce4+ se reduzem á Ce3+. Analises energéticas indicam que o processo é muito estabilizante, mais de 10 eV por Zr. Com o aumento da quantidade n de adatomos de Zr na superfície, observa-se 4 × n reduções de Ce4+ e migrações de O2- de dentro da superfície para próximo dos Zr4+, formando agregados de ZrO2 sobre a superfície. A migração de O se deve a dois fatores, a interação dos O2- com Zr4+ no agregado é mais estável do que a interação dos O2- com Ce3+ dentro da superfície, e a migração de O diminuir a tensão causada pelo maior raio do Ce3+ em relação ao Ce4+. Em adição, foi encontrado uma tendência de estabilidade para os Zr4+ migrarem para sítios Ce dentro da superfície, devido a maior quantidade de coordenações Zr-O e a redução da tensão criada pelos Ce3+. / Cerium oxides (CeOx, 3/2≤ x ≤ 2) based catalysts are employed in several reactions with high economic interest, such as the reaction in three-way-catalysts. It is well know that is possible to improve the ceria catalytic properties, by mixing with zirconium oxide and adding metallic particles over the material surface. Meanwhile, the deposition of Zr atoms over CeO2(111) is little explored although it has already been used for synthesis Ag nanoparticles of controlled size. One of the particularities of the Zr/CeO2(111) systems is to form islands of height between 1,5 and 3,0 Å on the surface of the ceria, which are suggested in the literature to be Zr-O and O-Zr-O layers. However, the nature and magnitudes of interactions between Zr and CeO2 surface are little know, as well as the CeO2 modifications induced by Zr and the mechanisms for Zr oxidation and ZrO2 formation over the surface. Aiming to understand the Zr-CeO2(111) interactions and the ZrO2 formation over the CeO2(111), this mastering project perform a theoretical study of n (1 ≤ n ≤ 4) Zr adatoms absorption over CeO2(111), and the ZrO2 formation over CeO2(111). The charge analysis indicated charge transfer from Zr adatons to the surface together with change in species oxidation state. The Zr oxidize to Zr4+ and interact with surface O2- , where four Ce4+ cations reduce to Ce3+. Energetic analysis pointed out that the process is very stabilizing, more than 10 eV per Zr adatom. With the increase of quantity n of Zr adatoms over the surface, it is observer 4 × n Ce4+ reductions and O2- migrations from inside surface to close the Zr4+, forming ZrO2 aggregates over the surface. The O migration occurs because of two reasons, the O2- interaction with Zr4+ in the agregate is more stabilizer than the interaction of O2- with Ce3+ inside the surface, and the O migration decrease the strain produced bue to the radius of Ce3+ being greater than the Ce4+ radius. In addition, was found a stability trend for Zr4+ to migrate to inside surface Ce sites, due of the more Zr-O coordinations and release of the strain induced by Ce3+.

Materiais cerâmicos obtidos a partir de pós nanocristalinos permitem a obtenção de excelentes propriedades após sinterização, devido à possibilidade de redução da temperatura final de sinterização com conseqüente refinamento microestrutural e excelente densificação. Nesse contexto, a zircônia tetragonal (ZrO2 (t)) tem um importante papel, pois suas características intrínsecas, tais como a transformação martensítica (ZrO2 (t-m)), permitem o desenvolvimento de excelentes propriedades, destacando-se a elevada tenacidade à fratura e resistência a flexão, tornando-a um material diferenciado visando aplicações nobres onde propriedades mecânicas e confiabilidade sejam pré-requisitos. Visando otimizar estas aplicações, se faz necessário conhecer as correlações entre as propriedades mecânicas e a microestrutura. Sendo assim, é de extrema importância promover a revelação microestrutural desses materiais, de forma padronizada e com representatividade estatística, o que exige cuidados nas técnicas de preparação ceramográfica. Nesse trabalho pretende-se caracterizar microestruturalmente cerâmicas a base de ZrO2(Y2O3) nanométrica, visando estudar os efeitos da temperatura e do tempo de sinterização na cinética de crescimento de grão. Foi definida uma rota de preparação e análise ceramográfica propondo seqüência de lixas e panos de polimento, assim como cargas e tempos em cada etapa. As amostras foram atacadas termicamente e micrografias foram obtidas. As micrografias foram processadas por rotinas de análise digital de imagens, visando definir padronizações para determinação de parâmetros microestruturais de interesse, tais como distribuição de tamanhos de grãos, densidade de grãos por unidade de área, razão de aspecto, etc. Foi estudado o efeito das condições de sinterização (temperatura final e tempo de isoterma) no crescimento de grãos. / Ceramic materials obtained from nanocrystalline powders enable the obtaining of excellent properties after sintering, due to the possibility of reducing the final sintering temperature with consequent microstructural refinement and excellent densification. In this context, tetragonal zirconia (ZrO2 (t)) has an important role, since their intrinsic characteristics, such as the martensitic transformation (ZrO2 (t-m)), allow the development of excellent properties, highlighting the high tenacity to fracture and resistance to bending, making it a differentiated material aiming noble applications where mechanical properties and reliability are prerequirements. In order to optimize these applications, it is necessary to know the correlations between the mechanical properties and microstructure. Thus, it is extremely important to promote the microstructural disclosure of these materials, in a standardized manner and with statistical representativeness, which requires care with the ceramographic preparation techniques. This work aims to microstructurally characterize ceramics based on nanometric ZrO2(Y2O3), looking for the study of the effects of the sintering temperature and time on the graingrowth kinetics. It was defined a route for ceramographic preparation and analysis proposing a sequence of sandpapers and polishing cloths, as well as loads and times at each stage. The samples were thermally etched and micrographs were obtained. The micrographs were processed through routines of digital image analysis, aiming the definition of standards for the determination of microstructural parameters of interest, such as distribution of grain sizes, density of grains per unit of area, aspect ration, and others. It was studied the effects of the sintering conditions (final temperature and time of isotherm) on the grain growth.

Die vorliegende Arbeit entstand im Rahmen einer Kooperation des Forschungszentrums Dresden-Rossendorf mit Qimonda Dresden GmbH & Co. OHG. Mithilfe der hochauflösenden Rutherford-Streuspektrometrie (HR-RBS) wurden das Diffusionsverhalten und Schichtwachstum von ZrO2 auf SiO2 und TiN im Anfangsstadium untersucht. Auf Grund der exzellenten Tiefenauflösung von 0,3 nm an der Oberfläche stand die Analyse von Konzentrationsprofilen in ultradünnen Schichten, respektive an deren Grenzflächen im Vordergrund. Zur qualitativen Verbesserung der Messergebnisse wurde erstmals ein zweidimensionaler positionsempfindlicher Halbleiterdetektor in den Aufbau der HR-RBS implementiert und charakterisiert. Außerdem wurde ein Messverfahren in Betrieb genommen, das mögliche Schädigungen durch den Ioneneintrag in die Messprobe minimiert. Durch die Optimierung der experimentellen Bedingungen und die Entwicklung eines Programmpaketes zur Unterstützung des Analysten konnte ein effizienter Routine-Messablauf erstellt werden. Im Moment einer binären Kollision zwischen einfallendem Ion und Targetelement kommt es bei kleinem Stoßparameter zu Veränderungen des Ladungszustands der gestreuten Ionen, insbesondere durch die abrupte Geschwindigkeitsänderung des Projektils und der Überlappung der Elektronenwolken. Bei der HR-RBS mit Energie separierendem Dipolmagneten muss zur Interpretation von Streuspektren die Ladungszustandsverteilung der gestreuten Projektile bekannt sein. Erstmalig konnte eine signifikante Abhängigkeit der Ladungszustandsverteilung gestreuter C-Ionen sowohl von der Schichtdicke als auch der Ordnungszahl des detektierten Targetelements, hier der vierten Nebengruppe, nachgewiesen werden. Diese gewonnen Erkenntnisse ermöglichten systematische Untersuchungen zum ZrO2-Schichtwachstum im Anfangsstadium. Zur Herstellung der ZrO2-Schichten wurde die Atomlagenabscheidung (ALD) verwendet. Anhand der nachgewiesenen Agglomeration von ZrO2 auf nativen SiO2 wurde mithilfe der Rasterkraftmikroskopie (AFM) zur Bestimmung von Oberflächenrauigkeiten eine Methode konzipiert, welche die Auswirkung lokaler Schichtdickeninhomogenitäten auf die niederenergetische Flanke eines Streuspektrums berücksichtigt. Auf dieser Grundlage durchgeführte Simulationsrechnungen ergeben, dass keine Diffusion von Zr in die darunter liegende Schicht stattfand, jedoch eine ZrSiO4-Grenzflächenschicht existiert. Für das Wachstum von ZrO2 auf TiN wird aus den hoch aufgelösten Streuspektren ein völlig anderes Verhalten abgeleitet. Messungen zu Oberflächentopografien der TiN-Schicht liefern nicht zu vernachlässigende Werte für die Rauigkeit. Um den Einfluss der Oberflächenrauigkeit auf die Form des hoch aufgelösten Spektrums erfassen zu können, wurde eine Software entwickelt. Auf Basis von AFM-Messungen ermöglicht dieses Programm das Extrahieren einer Energieverteilung aus den Weglängen von ausschließlich an der Oberfläche gestreuten Ionen. Unter Berücksichtigung des Effekts der Oberflächenrauigkeit auf die HR-RBS Spektrenform konnte die Diffusion von Zr in das polykristalline TiN erstmals verifiziert werden. Die Beobachtungen weisen daraufhin, dass bereits nach dem ersten ALD-Zyklus ein geringer Anteil der deponierten Zr-Atome bis in eine Tiefe von etwa 3 nm in das TiN diffundiert. Die vorläufigen Ergebnisse legen Korngrenzendiffusion nahe.

Neste trabalho foram preparados e caracterizados catalisadores de cobalto suportados em y-Al2O3, CeO2, 20%CeO2-yAl2O3 e em soluções sólidas CexZr1-xO2 (0<= x<=1), pelo método de impregnação, com o objetivo de avaliar o desempenho destes frente à reforma a vapor e oxidativa do etanol. Na preparação dos catalisadores utilizou-se o teor de 20% em massa de cobalto, para os suportes y-Al2O3, CeO2 e 20%CeO2-y-Al2O3, e 10% para os suportes CexZr1-xO2. Para a caracterização dos sólidos, as técnicas utilizadas foram: Espectroscopia Dispersiva de Raios-X (EDX), Redução a Temperatura Programada com H2 (RTP-H2), Difração de Raios-X pelo método do pó (DRX), Adsorção de Nitrogênio pelo método B.E.T. e Espectroscopia na região do Ultravioleta e do Visível. As reações de reforma a vapor de etanol foram realizadas nas temperaturas de 400, 500 e 600oC com razões molares H2O/Etanol= 3/1 e 4/1. Já, os ensaios catalíticos de reforma oxidativa foram realizados a 500oC com razões molares H2O/Etanol/O2= 3/1/0,16 e 3/1/0,20. Através dos resultados de DRX e RTP-H2 verificou-se a formação da fase Co3O4 para todos os catalisadores. Para os catalisadores suportados em y-Al2O3 e 20%CeO2-y Al2O3 observou-se ainda a formação da fase CoO-Al2O3. Nos ensaios catalíticos de reforma a vapor do etanol foi verificado que as mais altas conversões do etanol em produtos e maiores seletividades a hidrogênio foram obtidas a 600oC e razão H2O/Etanol=3/1. A maior razão CO2/CO foi obtida a 500oC com o catalisador Co/Ce0,4Zr0,6O2. Observou-se também que a adição de oxigênio ocasionou uma diminuição na deposição de carbono. / Cobalt supported in yAl2O3, CeO2, 20%CeO2-yAl2O3 and CexZr1-xO2 (0<= x <= 1) solid solution, were prepared by impregnation and applied in steam and oxidative reforming of ethanol. In the preparation of the catalysts was used 20wt.% of cobalt with yAl2O3, CeO2 and 20%CeO2-yAl2O3 supports and 10wt.% with CexZr1-xO2 supports. The solids were characterized by X-Ray Dispersive Spectroscopy; Temperature Programmed of Reduction with H2 (TPR- H2); X-Ray Diffraction (XRD); Nitrogen Adsorption by B.E.T. method; Ultraviolet and Visible Spectroscopy. The ethanol steam reforming was carried out at 400, 500 and 600oC with molar rates H2O/Ethanol= 3/1 and 4/1. The ethanol oxidative reforming was carried out at 500 °C with molar rates H2O/Ethanol/O2 = 3/1/0.16 e 3/1/0.20. XRD and TPR-H2 results showed the formation of Co3O4 phase for all catalysts. For the catalysts supported in y-Al2O3 and 20%CeO2-y-Al2O3 was still observed the formation of the CoO-Al2O3 phase. In the ethanol steam reforming the higher conversion was obtained at 600°C and the best H2 selectivity was observed with the H2O/Etanol=3/1 molar ratio. The higher CO2/CO ratio was observed at 500oC with Co/Ce0,4Zr0,6O2 catalyst. Already, the addition of oxygen caused a decrease in the carbon deposition.

Neste trabalho, foi estudada a sinterização de Nanoestruturas de zircônia estabilizada com ítria, ZrO2-Y2O3. Pós de ZrO2-3%mol de Y2O3 com tamanhos nanométricos e área superficial específica de 16,2 m2/g, foram compactados uniaxialmente em pressões variando entre 12,3MPa e 73,5MPa. Nestas pressões, as amostras compactadas atingiram densidade à verde entre 33% e 44,3%. Os compactos foram sinterizados por dilatometria de 1.250ºC até 1.4000C e os resultados indicaram que a temperatura de início de densificação está próxima a 1.0000C, independente da pressão de compactação aplicada. Temperaturas da ordem de 1.4000C são necessárias para a densificação total do compacto. Comparativamente pós microestruturados de ZrO2-3%mol Y2O3 (área superficial de 7,0 m2/g), foram compactados a 73,5MPa e alcançou densidade a verde de 44,2%. Este material apresentou início da retração próximo a 1.2000C, sugerindo que o uso de pós nanoestruturados reduziu a temperatura de sinterização em 2000C. A sinterização convencional dos pós nanoestruturado foi realizada em temperaturas entre 1.2500C e 1.4000C, com patamares entre 2 e 16h. Os pós microestruturados foram submetidos à sinterização em temperaturas de até 1.6000C, com os mesmos patamares. Os resultados indicaram que em todas as condições de sinterização e indiferentemente do pó utilizado, apenas a fase ZrO2 tetragonal foi encontrada. Além disso, a densidade relativa (DR) dos nanopós variou entre 92%(1.2500C-0h) e superior a 99%(acima de 1.3500C- 4h). Análises microestruturais indicaram a presença de grãos refinados com tamanho médio de 0,18?m (DR=92%,) para nanopós sinterizados a 1.2500C-0h, e tamanho médio de 0,95?m (DR=100%, 1.4000C-16h). Os pós micrométricos apresentaram tamanho de grão médio de 0,39?m (DR=98,8%) para cerâmicas sinterizadas a 1.5300C-0h e tamanho de grão médio de 1,84?m (DR=100%) para cerâmicas sinterizadas a 1.600-0h. Os expoentes de crescimento de grão calculados foram da ordem de 2,8 e 2,3 para. nanoparticulas e microparticulas, respectivametne, indicando que mecanismo de difusão pelos contornos de grão foi preponderante nos materiais estudados. Os valores de energia de ativação para o crescimento de grão calculados foram de 141,3kJ/mol e 244,7kJ/mol, respectivamente, indicando que os pós micrométricos necessitam de maior consumo energético para promover o crescimento de grão. Os resultados são discutidos em função de associar os fenômenos de densificação e crescimento de grão com o tamanho das partículas utilizadas. / We studied the sintering of nanoparticles of yttria stabilized zirconia, ZrO2-Y2O3. Powders of ZrO2-Y2O3 3 mol% with nanometric sizes and specific surface area of 16.2 m2/g, were uniaxially compacted at pressures ranging between 12.3 MPa and 73.5 MPa. Such pressures, the compressed samples reached the green density between 33% and 44.3%. The compacts were sintered by dilatometry up 1.400ºC and the results indicated that the onset temperature of densification is next to 1.000ºC, regardless of the compaction pressure applied. Temperatures of 1.400ºC are required to complete the densification of the compact. Compared microparticulate powders of ZrO2-Y2O3 3 mol% (specific surface area of 7.0 m2/g) were compressed to 73.5 MPa and green density reached 44.2%. This material exhibited the beginning of the next retraction 1.200ºC, suggesting that the use of powder nanopatticulados reduced sintering temperature of 200ºC. The conventional sintering of nanoparticle powders was undertaken at temperatures between 1.400ºC and 1.250ºC, with levels between 2 and 16h. The microparticulate powders were subjected to sintering at temperatures up to 1.600ºC with the same levels. The results indicated that under all conditions, and sintering the powder used interchangeably, only tetragonal ZrO2 phase was found. Furthermore, the relative density (RD) of nanoparticles ranged from 92% (1.250ºC- 0h) and greater than 99% (above 1.350ºC-4h). Microstructural analysis indicated the presence of refined grains with average size of 0.18 ? m (DR = 92%) for nanoparticles sintered at 1.250ºC-0h, and average size of 0.95 ?m (DR = 100%, 1.400ºC -16h). The powders were micron average grain size of 0.39 ?m (DR = 98.8%) to the sintered ceramic 1.530ºC-0h and the average grain size of 1.84 ?m (DR = 100%) of sintered ceramics the 1.600 ºC-0h. The grain growth exponents calculated were the order of 2.8 and 2.3 for nanoparticles and microparticles, respectively, and indicating that the mechanism of grain boundary diffusion was predominant in the studied materials. The values of activation energy for the grain growth were calculated 141.3 kJ/mol and 244.7 kJ/mol, respectively indicating that the powder micrometric require more energy to promote grain growth. The results are discussed in terms of the associated phenomena of densification and grain growth in the particle size used.

Die vorliegende Arbeit entstand im Rahmen einer Kooperation des Forschungszentrums Dresden-Rossendorf mit Qimonda Dresden GmbH & Co. OHG. Mithilfe der hochauflösenden Rutherford-Streuspektrometrie (HR-RBS) wurden das Diffusionsverhalten und Schichtwachstum von ZrO2 auf SiO2 und TiN im Anfangsstadium untersucht. Auf Grund der exzellenten Tiefenauflösung von 0,3 nm an der Oberfläche stand die Analyse von Konzentrationsprofilen in ultradünnen Schichten, respektive an deren Grenzflächen im Vordergrund. Zur qualitativen Verbesserung der Messergebnisse wurde erstmals ein zweidimensionaler positionsempfindlicher Halbleiterdetektor in den Aufbau der HR-RBS implementiert und charakterisiert. Außerdem wurde ein Messverfahren in Betrieb genommen, das mögliche Schädigungen durch den Ioneneintrag in die Messprobe minimiert. Durch die Optimierung der experimentellen Bedingungen und die Entwicklung eines Programmpaketes zur Unterstützung des Analysten konnte ein effizienter Routine-Messablauf erstellt werden. Im Moment einer binären Kollision zwischen einfallendem Ion und Targetelement kommt es bei kleinem Stoßparameter zu Veränderungen des Ladungszustands der gestreuten Ionen, insbesondere durch die abrupte Geschwindigkeitsänderung des Projektils und der Überlappung der Elektronenwolken. Bei der HR-RBS mit Energie separierendem Dipolmagneten muss zur Interpretation von Streuspektren die Ladungszustandsverteilung der gestreuten Projektile bekannt sein. Erstmalig konnte eine signifikante Abhängigkeit der Ladungszustandsverteilung gestreuter C-Ionen sowohl von der Schichtdicke als auch der Ordnungszahl des detektierten Targetelements, hier der vierten Nebengruppe, nachgewiesen werden. Diese gewonnen Erkenntnisse ermöglichten systematische Untersuchungen zum ZrO2-Schichtwachstum im Anfangsstadium. Zur Herstellung der ZrO2-Schichten wurde die Atomlagenabscheidung (ALD) verwendet. Anhand der nachgewiesenen Agglomeration von ZrO2 auf nativen SiO2 wurde mithilfe der Rasterkraftmikroskopie (AFM) zur Bestimmung von Oberflächenrauigkeiten eine Methode konzipiert, welche die Auswirkung lokaler Schichtdickeninhomogenitäten auf die niederenergetische Flanke eines Streuspektrums berücksichtigt. Auf dieser Grundlage durchgeführte Simulationsrechnungen ergeben, dass keine Diffusion von Zr in die darunter liegende Schicht stattfand, jedoch eine ZrSiO4-Grenzflächenschicht existiert. Für das Wachstum von ZrO2 auf TiN wird aus den hoch aufgelösten Streuspektren ein völlig anderes Verhalten abgeleitet. Messungen zu Oberflächentopografien der TiN-Schicht liefern nicht zu vernachlässigende Werte für die Rauigkeit. Um den Einfluss der Oberflächenrauigkeit auf die Form des hoch aufgelösten Spektrums erfassen zu können, wurde eine Software entwickelt. Auf Basis von AFM-Messungen ermöglicht dieses Programm das Extrahieren einer Energieverteilung aus den Weglängen von ausschließlich an der Oberfläche gestreuten Ionen. Unter Berücksichtigung des Effekts der Oberflächenrauigkeit auf die HR-RBS Spektrenform konnte die Diffusion von Zr in das polykristalline TiN erstmals verifiziert werden. Die Beobachtungen weisen daraufhin, dass bereits nach dem ersten ALD-Zyklus ein geringer Anteil der deponierten Zr-Atome bis in eine Tiefe von etwa 3 nm in das TiN diffundiert. Die vorläufigen Ergebnisse legen Korngrenzendiffusion nahe.

This diploma thesis deals with the study of microstructure development during the final stage of sintering of two zirconia based ceramic materials (tetragonal ZrO2 doped with 3 mol% of Y2O3 and cubic ZrO2 doped with 8 mol% of Y2O3). Conventional, microwave and SPS sintering methods were used. Achieved relative densities and mean grain sizes were evaluated for sintered materials. It was found that the non-conventional sintering methods are capable of rapid processing of ceramics with improved microstructure compared to conventional sintering.

The thesis was focused on preparation of bioceramic composite materials containing Ca-phosphates and zirconia fibers using electrophoretic deposition. A series of experiments were aimed at determining the appropriate composition of the suspensions. High-energy milling was used for preparing deposits with good physical and mechanical properties using EPD. The influence of milling time, the amount of monochloroacetic acid in isopropanol slurry indifferent electrolyte LiCl and ZrO2 were evaluated on the course deposition and the resulting properties of the deposits. Influence of sintering temperature, the milling time and the fiber content of ZrO2 on the chemical and structural composition was determined by X-ray analysis, measurement of density and structural analysis using a scanning electron microscope. Mechanical and bioactive properties of sintered deposits were determined depending on the milling time and content of ZrO2 fibers.

The stable interfaces between NiO and ZrO2 reached by nanofilms interface rotation method are reported in this study. Epitaxial nanofilms of NiO and ZrO2 were synthesized on single crystal NaCl (001), (011), (111) surfaces. All nanofilms are investigated by transmission electron microscopy and selected-area diffraction (SAD) patterns. Composite nanofilms were formed by overlapping nanofilms of NiO and ZrO2 at difference angles and thermally treated. The rotation process and final stable interfaces in the overlapped nanofilms are analyzed by SAD patterns. Orientation relationships and interface rotation are analyzed. This study found five new interfaces. (1) (001)N/ Z¡A[110]N//[110]Z (2) (001)N/ Z¡A[100]N//[110]Z (3) N/ Z¡A[110]N//[110]Z (4) N/ Z¡A[111]N//[110]Z (5) N/ Z¡A[001]N//[110]Z

This thesis is about the phase transformation, shape, size distribution and coalescence of TiO2 (part I) and ZrO2 (part II) nanopartilces produced by Nd-YAG laser ablation on metal targets under oxygen background gas, and characterized by analytical electron microscopy. The optimum laser ablation condition that satisfactory and routinely yield high-pressure phases of TiO2 (i.e. £\-PbO2-type and fluorite-related structures) and ZrO2 with high residual stress were reported. Part I-1 focuses on physical coagulation, by Van der Waals force, of the TiO2 condensates at temperatures up to about 1000 K as a result of post-condensation radiant heating. In part I-2, imperfect oriented attachment of nanoparticles over specific surfaces is rationalized to cause accretion and defects for the rutile condensates. Brownian motion may proceed above a critical temperature for anchorage release at the interface of imperfect attached nanoparticles until an epitaxial relationship is reached. Part I-3 deals with further the Brownian-type rotation of the imperfectly impinged £\-PbO2-type TiO2 and rutile nanocondensates until interfacial-energy cusp was reached. In part I-4 laser ablation condensation synthesis of dense TiO2 polymorphs and their phase transformations were documented. Part II-1 is about dense tetragonal (t)-ZrO2 and cubic (c-) nanocondensates which were synthesized under very rapid heating and cooling by pulsed Nd-YAG laser ablation with oxygen background gas. The t-ZrO2 nanoparticles were found to form deformation twins/faults and followed unique transformation path upon local electron dosage. Electron diffraction indicated that the dense c- and t- phase with specific size and residual stress were allowed to relax and/or kinetically phase change into lower-energy state as constrained by the intersections of the internal energy vs. cell volume plots calculated for the two polymorphs (Part II-2).