This thesis deals with the subject of fibre optic magnetic field sensors utilizing iron garnet materials. Such materials exhibit a large Faraday rotation which make them advantageous for application in compact mag­netic field sensors. After an introduction, in which fibre optic sensors and optical methods to measure electric current are reviewed, the original research work is summarized. A system for the measurement of the magneto-optic properties of trans­parent materials is described. Measurement results, showing the influence of temperature, magnetic field direction and sample treatment on the magneto-optical proper­ties of YIG-crystals, are presented. The proper­ties of thin magneto-optical waveguiding films have also been studied using different light coupling methods. Measurement results obtained for holo­graphic grating, prism and edge (end-fire) light coupling to different substituted YIG films are presented. It is shown that the launching method may affect the properties to be measured. The design and performance of several versions of extrinsic guided wave fibre optic magnetic field sensors are then reported. The sensors employ substi­tuted YIG (Yttrium Iron Garnet, Y3Fe5O12) thin film waveguides as sensing elements. Polari­zation maintaining fibres were used as feed and return to provide two signal channels. The signals were combined in a balanced measure­ment system, providing insensitivity to both fluctuations in optical power and loss. Sensors have been made both with separate fibres to guide the light to and from the sensing element and with a single fibre for both functions. The two fibre version, although less ”elegant”, is found to have a better performance. This version also makes it possible to determine both the magnitude and sign of the magnetic field. Measurement results indicate a usable measurement range of at least several mT with a noise equivalent magnetic field level of less than 8 nT/root(Hz). The design and performance of multimode fibre optic magnetic field sensors utilizing the Faraday effect in an epitaxially grown thick (YbTbBi)IG film is also described. This type of sensor is found to be linear over a range from 27 mT to less than 270 nT. Sensor prototypes suitable for current monitoring in high voltage transmission lines have also been developed. / QC 20111209 / YIG

Neste trabalho foram produzidos Interferômetros Mach-Zehnder (IMZ) a partir de guias de onda do tipo pedestal com filmes finos de Bi₂O₃-WO₃-TeO₂ (BWT) como camada de núcleo para aplicações em sensores ópticos integrados. A influência dos parâmetros e dos materiais utilizados nas etapas de processo foi verificada. Os valores de índice de refração efetivo e coeficiente de absorção em função do comprimento de onda foram obtidos para os filmes finos BWT. Os guias de onda pedestais foram caracterizados por Microscopia Eletrônica de Varredura, medidas de perda por propagação e perfis de campo próximo em 633 nm e 1050 nm. Os valores mínimos obtidos nas perdas por propagação foram de ~1,5 dB/cm em 633 nm e 3,0 dB/cm em 1050 nm. As medidas de perfis de campo próximo mostraram que guias de onda com larguras superiores a 7 m apresentaram comportamento multimodo. Foram obtidos IMZs que apresentaram guiamento de luz por toda a estrutura, com comportamento multimodo. Sensores ópticos de pressão e temperatura foram produzidos. A fabricação de diafragmas através do processo de corrosão úmida do silício é apresentada no sensor de pressão. Sensores ópticos de temperatura foram produzidos com filamentos metálicos. As cavidades ópticas não foram obtidas nesse sensor. A potência de luz na saída dos sensores de temperatura foi medida em função da diferença de potencial aplicada no filamento metálico. Os resultados apresentados mostram que guias de onda do tipo pedestal produzidos com núcleo de BWT são promissores para aplicações em sensores ópticos integrados. / In this work Mach-Zehnder Interferometers (MZI) were produced from the pedestal-type waveguides with Bi₂O₃-WO₃-TeO₂ (BWT) thin films as the core layer for applications in integrated optical sensors. The influence of the parameters and materials used in the process steps was verified. The values of the effective refractive index and absorption coefficient as a function of wavelength were obtained for the BWT thin films. The pedestal waveguides were characterized by Scanning Electron Microscopy, by propagation loss measurements and near-field profiles at 633 nm and 1050 nm. The minimum values obtained by propagation losses were ~ 1.5 dB/cm at 633 nm and 3.0 dB/cm at 1050 nm. The measures of near-field profiles showed that waveguides with widths larger than 7 m presented multimode behavior. The MZIs obtained presented guiding light through the structure, with multimode behavior. Optical pressure sensors and temperature sensors were produced. The production of diaphragms using the wet etching process of silicon is presented on the pressure sensor. Optical temperature sensors were made with metallic filaments. Optical cavities were not obtained in this sensor. The light power in the output of the temperature sensors was measured as the voltage applied to the metal filament. The results show that the waveguides produced with pedestal-type and BWT thin films as core layer are promising for applications in integrated optical sensors.

Orientador: José Antonio Siqueira Dias / Tese (doutorado) - Universidade Estadual de Campinas, Faculdade de Engenharia Elétrica e de Computação / Made available in DSpace on 2018-08-21T18:07:20Z (GMT). No. of bitstreams: 1 BiazonFilho_AlcinoJose_D.pdf: 3212736 bytes, checksum: 5eb7bde925a233493806c588f3c39cfe (MD5) Previous issue date: 2012 / Resumo: Sensores de fibra óptica são imunes à interferência eletromagnética (EMI), e são uma excelente escolha para ser usado em ambientes eletricamente ruidosos aplicações em sensoriamento remoto, incluindo aeroespacial, ferroviário equipamentos de segurança militar e em linhas de alta tensão. Outras vantagens incluem o fato de que eles são compactos, leves e os sinais de medição podem ser transmitidos a distâncias muito grandes (da ordem de km). Os interrogadores convencionais para redes de Bragg (FBG) do sensor são equipamentos de custo elevado e não pode ser utilizado em aplicações de baixo custo. Neste trabalho é apresentada uma nova técnica de interrogação robusta e de baixo custo que apresenta uma boa precisão. A técnica, que utiliza um circuito de retroalimentação eletrônico para estabilizar o ponto de operação DC das grades de Bragg, permite a medição simultânea de ambos sinais AC e DC. Um protótipo do interrogador proposto foi projetado e implementado. A técnica exige apenas três componentes ópticos: um laser distribuído, um acoplador óptico e um fotodiodo. O interrogador foi testado com sucesso em uma aplicação de DC (medição de temperatura) e uma aplicação AC (medição de corrente elétrica). Os resultados experimentais mostraram que o controle eletrônico em malha fechada pode controlar o ponto de operação da FBG com uma precisão de ± 2 ppm / Abstract: Fiber optic sensors are immune to electromagnetic interference (EMI), and are an excellent choice for being used in electrically noisy environments sensing applications, including aerospace, rail, military security equipment and in high voltage power lines. Other advantages include the fact that they are compact, lightweight and the measured signals can be transmitted at very large distances (of the order of kilometers). The conventional interrogators for Fiber Bragg Gratings (FBG) sensor are high cost equipment and cannot be used in low cost applications. In this work it is presented a novel robust and low cost interrogation technique that presents good accuracy. The technique, which uses an electronic feedback loop to stabilize the DC operating point of the Bragg gratings, allows the simultaneous measurement of both AC and DC signals. A prototype of the proposed interrogator was designed and implemented. The technique requires only three optical components: a Distributed Feedback Laser, an optical coupler and one photodiode. The interrogator has been successfully tested in a DC application (temperature measurement) and an AC application (electrical current measurement). Experimental results showed that the electronic feedback loop can control the operation point of the FBG with a precision of ±2 ppm / Doutorado / Eletrônica, Microeletrônica e Optoeletrônica / Doutor em Engenharia Elétrica

As the demand for energy increases, competition for a sustainable alternative to non-renewable energy resources has resulted in the growth of the photovoltaic industry. Although most photovoltaic technologies are based on crystalline silicon, thin film technologies have been developed with the expectation of generating a comparably high-performing product with lower processing costs. These materials have demonstrated sufficiently high optoelectronic performance to enable commercialization but concerns such as material scarcity limit terawatt level power production.<div><br></div><div>In the continuous pursuit of earth abundant solar absorber materials appropriate for thin film technologies, enargite Cu3AsS4 has been identified as a promising material due to its ideal direct band gap, stability, and high absorption. Recent efforts have demonstrated this class of copper chalcogenides exhibits band gap tunability and has solution processing capabilities for potentially scalable manufacturing. Furthermore, recent first-principles calculations of enargite Cu3AsS4 have hypothesized this material may have high carrier mobility and defect-tolerant optoelectronic properties, which further support investigation into this material. <br></div><div><br></div><div>In this dissertation, a novel reactive deposition processing route has been developed which has produced dense, single-phase enargite thin films. A champion device efficiency of 0.54% was achieved following a post deposition etching procedure on these films, which demonstrates the density and observable secondary phases were not limiting to initial nanoparticle-based device performances. Together with recent modeling efforts, the non-ideal band alignment with both the back contact and diode junction is concluded to be the primary limiting factor for high efficiency devices. <br></div><div><br></div><div>As this technology contains arsenic, concerns have been raised about its potential carcinogenicity and toxicity. Similar concerns were raised during the development of cadmium telluride technology, but these concerns have been mitigated through careful life cycle analyses and identifying strategies for responsible life cycle management. Therefore, a life cycle analysis and two risk assessments have been completed on Cu3AsS4 systems. Although emissions of arsenic and its contributions to life cycle impacts are expected to be low due to the small quantity required, hot spots have been identified to reduce waste and emissions. Reduction strategies for this material system are found to be applicable to other PV systems and include minimizing molybdenum sputter waste, reusing and recycling balance of system components, and investigating low-energy processing routes on thin substrates. This work serves to establish a basis on which the potential environmental implications of this thin film technology are understood. <br></div><div><br></div><div>This dissertation will serve as a guide toward the technical and environmental development of Cu3AsS4 thin films. Having a life cycle perspective during the systematic development of a technology will enable sustainable engineering. Furthermore, the processing and characterization methods detailed herein are expected to be generally applicable to other copper chalcogenide systems. <br></div>

Atomically thin 2D layered semiconductor materials such as Transition Metal Di-Chalcogenides (TMDCs) have great potential for use as flexible, ultra-thin photovoltaic materials in solar cells due to their favorable photon absorption and electronic transport properties. In this dissertation, the electronic properties, such as band structure and bandgap, and optical absorption properties of a TMDC known as Tungsten Disulfide (WS2) were obtained from Density Functional Theory (DFT) calculations to design conventional and unconventional solar cells. Using these properties, a 1 μm thick heterojunction solar cell based on monolayer and bulk WS2 together with amorphous silicon (a-Si) was modeled using numerical calculations and simulations. The maximum efficiency of this cell is 23.3% with Voc = 0.84 V and Jsc = 33.5 mA/cm2 under the AM1.5G terrestrial solar spectrum. Next, a similar but even thinner solar cell with a thickness of 200 nm, together with a light trapping structure and an anti-reflection coating layer, was modeled under the AM0 space solar spectrum; similar device performance efficiencies around 21-23% were obtained. The performance of these solar cell models is comparable to many commercial cells in both terrestrial and space photovoltaics. As conventional photovoltaics approach the Shockley-Queisser limit, the need for unconventional materials and approaches has become more apparent. Hybrid alloys of TMDCs exhibit tunable direct bandgaps and significant dipole moments. Dark state protection induced by dipole-dipole interactions forms new bright and dark states in the conduction band that reduce radiative recombination and enhance photon-to-electron conversion, leading to significantly higher photocurrents. In our work, current enhancement of up to 35% has been demonstrated by modeling dark state protection in a solar cell composed of Tungsten Diselenide (WSe2) and Tungsten Sulfo-Selenide (WSeS), with the potential to exceed the Shockley-Queisser limit under ideal conditions.

This dissertation presents the fabrication of hollow optical waveguides integrated on planar substrates. Similar in principle to Bragg waveguides and other photonic crystal waveguides, the antiresonant reflecting optical waveguide (ARROW) is used to guide light in hollow cores filled with liquids or gases. Waveguides with liquid or gas cores are an important new building block for integrated optical sensors. The fabrication method developed for hollow ARROW waveguides makes use of standard microfabrication processes and materials. Dielectric layers are deposited on a silicon wafer using plasma-enhanced chemical vapor deposition (PECVD) to form the bottom layers of the ARROW waveguide. A sacrificial core material is then deposited and patterned. Core materials used include aluminum, SU-8 and reflowed photoresist, each resulting in a different core geometry. Additional dielectric layers are then deposited, forming the top and sides of the waveguide. The sacrificial core is then removed in an acid solution, resulting in a hollow ARROW waveguide. Experiments investigating the mechanical strength of the hollow waveguides and the etching characteristics of the sacrificial core suggest design rules for the different core types. Integration of solid-core waveguides is accomplished by etching a ridge into the top dielectric layer of the ARROW structure. Improved optical performance can be obtained by forming the waveguides on top of a raised pedestal on the silicon substrate. Loss measurements on hollow ARROW waveguides fabricated in this manner gave loss coefficients of 0.26 cm-1 for liquid-core waveguides and 2.6 cm-1 for air-core waveguides. Fluorescence measurements in liquid-core ARROW waveguides have achieved single-molecule detection sensitivity. Integrated optical filters based on ARROW waveguides were fabricated, and preliminary results of a capillary electrophoresis separation device using a hollow ARROW indicate the feasibility of such devices for future investigation.

This thesis discusses the application of Slab Coupled Optical Fiber Sensors (SCOS) in a railgun. The specific goal of these sensors is to create an electric field profile at a specific point in the gun as the armature passes. The thesis explores the theory that powers the railgun as well as the principles of the SCOS sensors. It also elaborates on the various noise sources found throughout the detection system and concludes with a summary of the various field tests that were performed throughout this project. There are many benefits to using a railgun over traditional weapons in the field. These benefits not only include both safety and cost, but also greater overall defense capabilities. Unfortunately, the velocity skin effect (VSE) causes the current railgun designs to have limited life span through wear on the rails. In order to develop superior railguns and railgun armatures, the accurate detection of the VSE through measuring the electric field is of great interest. We used a SCOS, a small directionally precise dielectric sensor, as a small sensing area is required to be able to measure the electric fields inside of the rail gun. The actual usage of the SCOS within the railgun produced an additional set of problems that are not commonly encountered in the lab. The chief amongst these was noise from strain, RF pickup, and phase noise. This thesis also reports various methods used to reduce each of these noise sources.

Proposed are novel sensors for extreme environment power plants, laser beam analysis and biomedicine. A hybrid wireless-wired extreme environment temperature sensor using a thick single-crystal Silicon Carbide (SiC) chip embedded inside a sintered SiC probe design is investigated and experimentally demonstrated. The sensor probe employs the SiC chip as a Fabry-Perot (FP) interferometer to measure the change in refractive index and thickness of SiC with temperature. A novel temperature sensing method that combines wavelength-tuned signal processing for coarse measurements and classical FP etalon peak shift for fine measurements is proposed and demonstrated. This method gives direct unambiguous temperature measurements with a high temperature resolution over a wide temperature range. An alternative method using blackbody radiation from a SiC chip in a two-color pyrometer configuration for coarse temperature measurement and classical FP laser interferometry via the same chip for fine temperature measurement is also proposed and demonstrated. The sensor design is successfully deployed in an industrial test rig environment with gas temperatures exceeding 1200 C. This sensor is proposed as an alternate to all-electrical thermocouples that are susceptible to severe reliability and lifetime issues in such extreme environments. A few components non-contact thickness measurement system for optical quality semi-transparent samples such as Silicon (Si) and 6H SiC optical chips such as the one used in the design of this sensor is proposed and demonstrated. The proposed system is self-calibrating and ensures a true thickness measurement by taking into account material dispersion in the wavelength band of operation. For the first time, a 100% repeatable all-digital electronically-controlled pinhole laser beam profiling system using a Texas Instruments (TI) Digital Micro-mirror Device (DMD) commonly used in projectors is experimentally demonstrated using a unique liquid crystal image generation system with non-invasive qualities. Also proposed and demonstrated is the first motion-free electronically-controlled beam propagation analyzer system using a TI DMD and a variable focus liquid lens. The system can be used to find all the parameters of a laser beam including minimum waist size, minimum waist location and the beam propagation parameter M2. Given the all-digital nature of DMD-based profiling and all-analog motion-free nature of the Electronically Controlled Variable Focus Lens (ECVFL) beam focus control, the proposed analyzer versus prior-art promises better repeatability, speed and reliability. For the first time, Three Dimensional (3-D) imaging is demonstrated using an electronically controlled Liquid Crystal (LC) optical lens to accomplish a no-moving parts depth section scanning in a modified commercial 3-D confocal microscope. The proposed microscopy system within aberration limits has the potential to eliminate the sample or objective motion-caused mechanical forces that can distort the original sample structure and lead to imaging errors. A signal processing method for realizing high resolution three dimensional (3-D) optical imaging using diffraction limited low resolution optical signals is also proposed.

This dissertation demonstrates the first of its kind distributed magnetic field sensor based on a fiber optic distributed acoustic sensing (DAS) scheme. Ferromagnetic nickel and Metglas® were dispersed internally within a fiber optic preform and then drawn on an in-house fiber optic draw tower to lengths in the kilometers. Due to the close proximity of the ferromagnetic metals and fiber optic core, the magnetostrictive strain response of the ferromagnetic materials when exposed to a magnetic field would perturbate within the fiber cladding and transfer that strain, internally, to the fiber optic core. Strain resulting from the magnetostrictive effect allows the DAS based sensor to accurately translate strain into readable magnetic field data. Due to the high sensitivity seen in this sensor design, multiparameter sources, acoustic and magnetic fields, were tested and validated and a three dimensional magnetic-field vector sensor was proposed. Numerical analysis of the novel sensor design was first implemented using COMSOL Multiphysics, where inputs such as magnetostrictive element shape, size, distance, and number were first investigated. Upon optimizing system constraints, the sensor design was further modified such that single mode operation was consistent across multiple fiber draws while retaining high strain transfer from the ferromagnetic elements to the fiber optic core. Ferromagnetic material selection was evaluated as a function of the saturation magnetostriction constants and a total of 4 modules were used to fully characterize the complex physics involved in this sensor design. All fabrication and testing were performed in-house using a full scale 3-story fiber draw tower and custom environmental testing stations to imitate naturally occurring events such as magnetic or acoustic point sources. A unique stacking method was used to embed ferromagnetic nickel and Metglas® into a fiber optic preform which when combined with a custom fiber draw process resulted in consistent multi-material fibers drawn to lengths of 1-km. In-house testing facilities included different types of electromagnetic generators, in addition to a soil test bed, and an outdoor test bed which allowed 100 meters of fiber to be tested simultaneously. All tested sensors demonstrated high strain transfer capabilities on the order of 0.01-10 μϵ depending on the materials used, ferromagnetic rod number, and core to metal spacing. Due to the sensitivity of the system the difference between AC and DC was distinct, and directional magnetostriction was studied. Transverse and longitudinal magnetic wave propagation was controlled through a solenoid and rectangular Helmholtz coil, both built in-house. A three-dimensional magnetic field vector sensor was proposed due to the success of the magnetic field sensor, and a design was proposed and initially tested to validate direction as a function of field strength and distance. To summarize, this dissertation explores the first fully distributed magnetic field sensor using DAS based techniques and one of the first multi-material fiber draw processes which can produce consistent single mode fiber up to 1-km. Due to extensive FEA modeling, multiple iterations of the magnetic sensor were fully characterized and an equation describing the relationship between sensor design and strain transfer has been created and validated experimentally. Multi-parameter tests including acoustic and magnetic fields were implemented and an algorithm was developed to separate the mixed signals. Finally, a test was performed to demonstrate the feasibility of sensing magnetic fields directionally. Cumulative results demonstrate a high-quality sensor alternative to current designs which may surpass other magnetic sensors due to innate multi-parameter capabilities, in addition to the inexpensive production cost and extremely long operating lengths. / Doctor of Philosophy / This dissertation demonstrates the first of its kind distributed magnetic field sensor based on a fiber optic distributed acoustic sensing (DAS) scheme. Ferromagnetic nickel and Metglas® were dispersed internally within a fiber optic preform and then drawn on an in-house fiber optic draw tower to lengths in the kilometers. Due to the close proximity of the ferromagnetic metals and fiber optic core, the magnetostrictive strain response of the ferromagnetic materials when exposed to a magnetic field would perturbate within the fiber cladding and transfer that strain, internally, to the fiber optic core. Strain resulting from the magnetostrictive effect allows the DAS based sensor to accurately translate strain into readable magnetic field data. Due to the high sensitivity seen in this sensor design, multiparameter sources, acoustic and magnetic fields, were tested and validated and a three dimensional magnetic-field vector sensor was proposed. Numerical evaluation of the sensing structure was perused before experimental testing using COMSOL Multiphysics. Experimental and numerical evaluations were compared and showed a high degree of certainty which allowed expedited design modifications. Sensor characterization included scanning electron microscopy, and electron diffraction spectroscopy, which provided insight into material composition and fiber polishing quality. Due to the high-quality results attained in the combined acoustic and magnetic field tests, a final design was proposed to gather magnetic field data as a vector, showing both magnitude and direction. The 3D magnetic field vector sensor was partially validated based on a test which compared intensity with distance and a design and methodology was proposed to fully test and characterize this design. To summarize, a novel magnetic field sensor, capable of multi-parameter sensing, was proposed and tested experimentally and numerically resulting in a robust and highly sensitive design. The work presented here provides some of the first insights into multi-material fiber fabrication, an equation which provides an estimated relationship between magnetostrictive strain transfer onto a fiber optic core and the perceived DAS based sensor results, as well as a first of its kind multi-parameter distributed acoustic and magnetic field sensor.

This research serves to evaluate the ability of optical detection techniques to ascertain the lubricity of revenue service track from a moving platform for railroad applications. A literature review is presented that covers the rail vehicle dynamics that drive the need of Top-of-Rail lubrication and directly affect the manner in which the Top-of-Rail Friction Modifiers (TORFM) and flange grease both spread down rail and eventually wear away. This literature review also highlights previous research in the field of rail lubrication and the benefits that rail lubricants, specifically TORFM, provide for the railroads. Finally, the literature review covers the governing optical principals inherent to the synchronous spot radiometer that has been developed for use in the research as a gloss ratio instrument and also addresses the drawbacks and challenges inherent to applying this type of instrument in the railroad industry. The research then overviews previous rail lubricity sensors developed by the Railway Technologies Laboratory (RTL) at Virginia Tech and the lessons learned from their application. The preceding field testing conducting with a modified second generation rail lubricity sensor and a rail push car is briefly summarized with emphasis on the drawbacks and issues that were used to develop the third generation sensor used for this research. The development of the third generation sensor is covered, including the issues that it attempts to solve from its predecessor and the governing optical principals that govern the operation of the sensor. The laboratory evaluations conducting to commission the sensor are also covered in preparation for deploying the new third generation sensor in medium speed, medium distance revenue service testing. This includes a shakedown run on a siding in Riverside, VA prior to conducting mainline in-service testing. Finally, this research thesis covers the in-service testing on revenue track conducted with the new third generation rail lubricity sensor and the accompanying remote-controlled (RC) rail cart. The two components, when combined, create a Lubricity Assessment System which is capable of being operated at speeds upwards of 10 mph remotely from a follow hy-rail truck. The data collected from this field test is analyzed for the lubricity assessments that are able to be drawn from this initial phase of field service testing. The conclusions from this testing affirm the ability of optical methods to determine and evaluate Top-of-Rail (TOR) lubricity from a moving platform. Specifically, the new sensor is able to identify several local phenomena that demonstrate the high potential for errant evaluation of rail lubricity evaluation from spot check based methods that are solved by evaluating the track in a continuous, moving fashion. Based on the continuous moving data collected for this test, several new signal traits such as the spatial frequency (wavenumber) associated with the passing freight cart wheels in the lubricity signal and the phantom applicator effect of transient lubricity conditions at the entrances and exits of curves can be detected and investigated. The success of this research indicates the continued evaluation of lubricity signals from a moving platform is warranted and suggests the potential for introducing one of these systems to various track metrology cars deployed throughout the United States railroads. / Master of Science / The United States railroads have been employing rail lubricants to the rails since the beginning of the industry and have recently, in the past 20 years, introduced another type of lubricant: Top-of-Rail Friction Modifiers (TORFM). TORFM creates a third body layer between the train wheels and the Top-of-Rail surface to minimize asset wear of both the wheel and rail and to increase the train efficiency. As the United States railroads embrace Precision Scheduled Railroading (PSR), increased train efficiency can allow the railroads to run longer trains with fewer locomotives. This increases the efficiency and capability of the rail network and also decreases the fuel burned and the amount of rail and wheel wear. TORFM has been proven to be effective and is widely adopted, but the railroads are still in need of tools to determine the presence and absence of these thin and often nearly invisible layers of lubricant on the rail surface. This research uses lasers as tool to quantify the level of lubrication of the rail surface. The presence of rail lubricants, such as TORFM, on the rail surface change the amount of light that is reflected and scattered off the shiny steel surface. These changes are often small but can be captured by photodetectors housed in the instrument. By plotting the detected sensor values, trends in the lubricity signal can be tracked and evaluated to determine the presence or absence of rail lubricants and assess the overall quality of lubrication on the rail at specific locations down track. The research in this thesis takes existing methods that were used for single spot inspections and adapts them to a moving platform. The moving platform is able to continuously scan the Top-of-Rail surface as the instrument moves along and generates continuous moving evaluations of rail lubricity. This can be especially important when the lubricity is not uniform and allows for trends in the data to be analyzed to provide more consistent and precise evaluations of the lubricity trends down rail. Optical tools like this sensor, which are by nature non-contact sensors, can easily be adapted to existing track measurement railcars and deployed system wide. This solves a strong need for railroad engineers: to be able to identify the presence of rail lubricants and evaluate the effectiveness of their lubrication practices.