The production of metal powders by water atomisation is a well established process, which can be used to produce a wide range of particle sizes. A careful control of the particle size distribution is necessary, to atomise powders with a high quality and at a low production cost. Therefore, it is necessary to have a substantial knowledge of the relation between operational parameters and the particle size, to be able to produce water atomised metal powders with consistent and high yields. The main purpose with this thesis was to increase the knowledge about factors which affect the mass median particle size (d50) for water atomised metal powders. The specific objectives with the study were to develop a theoretical d50 model and to investigate the relation between the particle size and the physical properties of the liquid metal. Pilot scale experiments for liquid iron showed that alloy additions of carbon and sulphur decreased the d50 value, at a maintained liquid steel temperature before atomisation. Moreover, it was indicated that the reduced particle size at increased %C and %S contents may be related to a decreased viscosity and surface tension of the liquid metal, respectively. An alternative explanation could be that raised superheats at increased carbon contents increased the total available time for atomisation, which may have contributed to a reduction of the d50 value. The theoretical d50 model developed in this work showed a very good correlation to the current experimental data. The model considers the influence of surface tension, viscosity, melt stream diameter, water pressure, water jet angle and water to metal ratio. This model was further used to analyse how the d50 value was influenced by the viscosity and the surface tension. A reduced viscosity from 4∙9 to 2∙1 mPa s decreased the d50 value with 33%. In addition, the particle size was estimated to decrease with 21% by decreasing the surface tension from 1840 to 900 mN m-1. / Q 20120529

Denna licensiatavhandling behandlar oxidativ upplösning av UO2. Upplösning av UO2 studeras huvudsakligen då UO2-matrisen hos använt kärnbränsle förväntas fungera som en barriär mot frigörande av radionuklider i ett framtida djupförvar. Lösligheten av U(IV) är mycket låg under i djupförvaret rådande förhållanden emedan U(VI) har betydligt högre löslighet. Oxidation av UO2-matrisen kommer därför att påverka dess löslighet och därmed dess funktion som barriär. I denna avhandling studeras den relativa effektiviteten av en- och två-elektronoxidanter för upplösning av UO2. Vid låga oxidantkoncentrationer är utbytet för upplösningen för en-elektronoxidanter signifikant lägre än för två-elektronoxidanter. För en-elektronoxidanter ökar dock utbytet med ökande oxidanthalt, vilket kan förklaras av den ökade sannolikheten för två konsekutiva en-elektronoxidationer av samma reaktionssite och den ökade möjligheten till disproportionering. Radikaler och molekylära radiolysprodukters relativa inverkan på oxidativ upplösning av UO2 studeras också i denna avhandling genom mätning av mängden upplöst U(VI) i γ-bestrålade system som dominerades av olika oxidanter. Dessa studier visade att upplösningshastigheten av UO2 kan uppskattas från oxidantkoncentrationer framtagna genom simuleringar av radiolys i motsvarande homogena system och hastighetskonstanterna för ytreaktionerna. Simuleringarna visar att de molekylära oxidanterna kommer vara de viktigaste oxidanterna i alla system i denna studie vid långa bestrålningstider (>10 timmar). Vid liknande simuleringar av α-bestrålade system fanns att vid förhållanden relevanta för ett djupförvar för använt kärnbränsle, är det endast de molekylära oxidanterna (i huvudsak H2O2) som är av betydelse för upplösningen av bränslematrisen. Då använt kärnbränsle innehåller en mängd radionuklider som utsätter UO2-matrisen för kontinuerlig bestrålning, är det av vikt att undersöka hur bestrålning påverkar reaktiviteten av UO2. Bestrålningseffekten på reaktionen mellan UO2 och MnO4- studerades. Dessa försök visade att bestrålning av UO2 vid doser >40 kGy leder till att reaktiviteten ökar upp till 1.3 gånger reaktiviteten av obestrålad UO2. Den ökade reaktiviteten kvarstår efter bestrålningen och effekten kan därför möjligen tillskrivas permanenta förändringar i materialet. Vid uppskattning av reaktiviteten hos använt kärnbränsle måste hänsyn tas till denna effekt då bränslet redan efter ett par dagar i reaktor blivit utsatt för doser >40 kGy. Det har tidigare föreslagits att hastigheten för en heterogen västka/fast-fas reaktion är beroende av partikelstorleken hos det fasta materialet, vilket har studerats för UO2-partiklar i denna avhandling. Experimentellt bestämda kinetiska parametrar jämförs med de föreslagna ekvationerna för fyra storleksfraktioner av UO2-pulver och en UO2-pellet. Studien visade partikelstorleksberoendet av andra ordningens hastighetskonstant och aktiveringsenergin för oxidation av UO2 med MnO4- beskrivs relativt väl av de föreslagna ekvationerna. / The general subject of this thesis is oxidative dissolution of UO2. The dissolution of UO2 is mainly investigated because of the importance of the UO2 matrix of spent nuclear fuel as a barrier against radionuclide release in a future deep repository. U(IV) is extremely insoluble under the reducing conditions prevalent in a deep repository, whereas U(VI) is more soluble. Hence, oxidation of the UO2-matrix will affect its solubility and thereby its function as a barrier. In this thesis the relative efficiency of one- and two electron oxidants in dissolving UO2 is studied. The oxidative dissolution yield of UO2 was found to differ between one- and two-electron oxidants. At low oxidant concentrations the dissolution yields for one-electron oxidants are significantly lower than for two-electron oxidants. However, the dissolution yield for one-electron oxidants increases with increasing oxidant concentration, which could be rationalized by the increased probability for two consecutive one-electron oxidations at the same site and the increased possibility for disproportionation. Furthermore, the relative impact of radical and molecular radiolysis products on oxidative dissolution of UO2 is investigated. Experiments were performed where the amount of dissolved U(VI) was measured in γ-irradiated systems dominated by different oxidants. We have found that the UO2 dissolution rate in systems exposed to γ-irradiation can be estimated from oxidant concentrations derived from simulations of radiolysis in the corresponding homogeneous systems and rate constants for the surface reactions. These simulations show that for all systems studied in this work, the molecular oxidants will be the most important oxidants for long irradiation times (>10 hours). Similar simulations of α-irradiated systems show that in systems relevant for a deep repository for spent nuclear fuel, only the molecular oxidants (mainly H2O2) are of importance for the dissolution of the fuel matrix. The effect on UO2 reactivity by irradiation of the material is of importance when predicting the spent fuel dissolution rate since the fuel, due to its content of radionuclides, is exposed to continuous self-irradiation. The effect of irradiation on the reaction between solid UO2 and MnO4- in aqueous solutions was studied. It was found that irradiation of UO2 at doses >40 kGy increases the reactivity of the material up to ~1.3 times the reactivity of unirradiated UO2. The increased reactivity remains after the irradiation and can possibly be attributed to permanent changes in the material. This issue must be taken into account when predicting the reactivity of spent nuclear fuel since the fuel is exposed to doses >40 kGy after only a few days in the reactor. It has earlier been suggested that the rate of a heterogeneous liquid-solid reaction depends on the size of the solid particles. This was investigated for UO2 particles in this thesis. Experimental kinetic parameters are compared to the previously proposed equations for UO2 powder of four size fractions and a UO2 pellet. We have found that the particle size dependence of the second order rate constant and activation energy for oxidation of UO2 by MnO4- is described quite well by the proposed equations. / QC 20101123

Silica gels containing incorporated heteropolyacids (HPAs) were synthesized in acidic media by co-condensation of tetraethoxysilane (TEOS) with phosphotungstic or phosphomolybdic acids using the sol-gel technique. The effect of the synthesis conditions on their structure and morphology was studied. Yields of modified materials were somewhat lower compared to non-modified silica gels. All materials were mesoporous but contained micropores in their structures. Presence of bands of Keggin's structures in FT-IR spectra along with absence of XRD patterns of crystalline HPAs confirmed their fine incorporation into silica network. Particle sizes of modified materials were 500-1100 nm except for the W-containing sample obtained with trimethylstearylammonium chloride, which was significantly lower. This unusual effect was attributed to stabilization of primary silica nanoparticles by interactions between the surfactant and HPA. High ratio HPA/TEOS resulted in partial loss of porosity. Obtained results might be used for optimization of synthesis of effective catalysts and adsorbents containing HPAs in mesoporous structure.

This project deals with the mixed micellar and interfacial properties of mixtures of three surfactants [sodium dodecyl sulphate (SDS), cetyltrimethylammonium bromide (CTAB), and tetraethylene glycol monododecyl ether (C12E4)] with ABA symmetrical triblock copolymer (Pluronic F127), which has many industrial applications. Evidence of F127 micellisation and interaction with surfactants in the aqueous phase is inferred through interfacial tension measurements. The solution containing diluted monomeric F127 showed complex formation with surfactants before the latter self-aggregate as pure micelles. The simultaneous presence of ionic surfactants and micellar F127 in solutions displayed a decrease of interfacial activity and led to the conclusion of F127 micelles disruption. C12E4 was found to interact differently with micellar F127 in forming mixed micelles, and no loss of interfacial activity was recorded. This “association-dissociation” behaviour of F127 and surfactants was leveraged to understand the stability of mineral oil in water emulsions formulated with them in the presence of sodium phosphate (Na3PO4). The mechanisms of emulsions breakdown were found to rely on aggregation behaviour and complex structure of F127 and surfactants mixtures in solution. Laser diffraction showed that unlike SDS and CTAB, mixed-emulsifier systems containing C12E4 are stable to both flocculation, Ostwald ripening and coalescence. Due to electrostatic repulsion between its head group and F127 hydrophilic block, and also because of the combined effect of Ostwald ripening and coalescence, CTAB emulsifier containing systems displayed quicker instability than SDS. SDS containing systems showed a progressive shifting of droplets size distributions to bimodality as SDS concentration was increased and heat exposure pursued, revealing the activity of two distinct population of droplets in the emulsions. More insight on the mechanisms underlying the stability of the three mixed emulsifier systems was gained in performing optical microscopy and rheology measurements; the results were found to be consistent with particle size distribution. / Dissertation (MSc (Applied Science: Chemical Technology))--University of Pretoria, 2020. / Chemical Engineering / MSc (Applied Science: Chemical Technology) / Unrestricted

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第19282号 / 工博第4079号 / 新制||工||1629(附属図書館) / 32284 / 京都大学大学院工学研究科社会基盤工学専攻 / (主査)教授 中川 一, 教授 藤田 正治, 准教授 川池 健司 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

京都大学 / 0048 / 新制・課程博士 / 博士(工学) / 甲第21096号 / 工博第4460号 / 新制||工||1693(附属図書館) / 京都大学大学院工学研究科都市環境工学専攻 / (主査)教授 高岡 昌輝, 教授 田中 宏明, 准教授 大下 和徹 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

Particle breakage can be significant in stirred vessels such as crystallizers. During crystallization, particle breakage can occur due to particle contact with other particles, the impeller, the suspension fluid, and/or the vessel. Such breakage produces fines and can cause filter plugging downstream. Although research has been conducted with respect to particle breakage, a comprehensive study is still needed to quantify the breakage occurring in stirred vessels. The overall goal of this research is to model the particle breakage occurring in a stirred vessel by analyzing the particle size and shape distributions that result from breakage. Breakage experiments are based on collision influences that affect the two dominant collisions types, crystal-to-crystal and crystal-to-impeller collisions. Results showed that the quantity of fines produced are affected by the solids concentration or magma density and suspension fluid utilized. Additionally, aqueous saturated solutions produced particle size distributions that differ from those obtained using a nonsolvent. Similar particle size distributions for two different materials (NaCl and KCl) are achieved in the same nonsolvent (acetonitrile) by adjusting the agitation rate using the Zwietering correlation to account for property differences; moreover, the same agitation rate adjustment produced similar distributions for KCl in acetone and acetonitrile which were both nonsolvents. However, modifications to the Zwietering correlation, such as changing the significance of the initial particle size, are proposed before this method of adjustment is deemed accurate. Number-based population modeling of particle breakage is achieved within 1-5% error for NaCl at each agitation rate investigated. Breakage modeling using a discretized population balance equation with Austin's equation for attrition and the power law form of the product function for fragmentation is a viable approach; however, more work is needed to increase the accuracy of this model.

Due to the endangerment of the June sucker (Chasmistes liorus), the lower two miles of Hobble Creek, Utah has been the focus of several restoration efforts. The portion of the creek between Interstate 15 and Utah Lake has been moved into a more "natural" channel and efforts are now being made to expand restoration to the east side of the freeway. This thesis reports on three different parts of a sedimentological analysis performed on Hobble Creek. The first part is a data set that contains information about the particle size distribution on the bed of Hobble Creek between 400 W and Interstate 15 in Springville, Utah. Particle size distributions were obtained for eleven sub-reaches within the study section. Particle size parameters such as D50 were observed to decrease from an average of 72 mm to 24 mm downstream from the 1650 W crossing and Packard Dam. Streambed armoring was observed along most of the reach. This data set can be used as input for PHABSIM software to determine the location and availability of existing spawning material for June sucker during a range of flows. The second part of this thesis compares predictions from four bed-load transport models to bed-load transport data measured on Hobble Creek. In general, the Meyer-Peter, Muller and Bathurst models overpredicted sediment transport by several orders of magnitude while the Rosgen and Wilcock methods (both calibrated models) were fairly accurate. Design channel dimensions resulting from the bed-load transport predictions diverged as a function of discharge. Once validated, the models developed in this section can be used by design engineers to better understand sediment transport on Hobble Creek. The models may also be applied to other Utah Lake tributaries. The third section of the thesis introduces a detailed survey data set that covers the Hobble Creek floodplain on the shifted section between Interstate 15 and Utah Lake with an approximate 10 foot resolution grid. Water surface elevations at two flows, along with invert, fence, saddles, and other points, are labeled in the survey. A comparison with a survey completed last year did not reveal any significant lateral changes caused by the 2010 spring runoff. Due to the potential importance of the side ponds to June sucker survival, this data set can be used to monitor sedimentation in the side ponds. It may also be used in a GSSHA model to determine the magnitude of flow that is required before each side pond will be connected to the main channel.

Cerium oxide has been used extensively for various applications over the past two decades. The use of cerium oxide nanoparticles is beneficial in present applications and can open avenues for future applications. The present study utilizes the microemulsion technique to synthesize uniformly distributed cerium oxide nanoparticles. The same technique was also used to synthesize cerium oxide nanoparticles doped with trivalent elements (La and Nd). The fundamental study of cerium oxide nanoparticles identified variations in properties as a function of particle size and also due to doping with trivalent elements (La and Nd). It was found that the lattice parameter of cerium oxide nanoparticles increases with decrease in particle size. Also Raman allowed mode shift to lower energies and the peak at 464 cm-1 becomes broader and asymmetric. The size dependent changes in cerium oxide were correlated to increase in oxygen vacancy concentration in the cerium oxide lattice. The doping of cerium oxide nanoparticles with trivalent elements introduces more oxygen vacancies and expands the cerium oxide lattice further (in addition to the lattice expansion due to the size effect). The lattice expansion is greater for La-doped cerium oxide nanoparticles compared to Nd-doping due to the larger ionic radius of La compared to Nd, the lattice expansion is directly proportional to the dopant concentration. The synthesized cerium oxide nanoparticles were used to develop an electrochemical biosensor of hydrogen peroxide (H2O2). The sensor was useful to detect H2O2 concentrations as low as 1µM in water. Also the preliminary testing of the sensor on tomato stem and leaf extracts indicated that the sensor can be used in practical applications such as plant physiological studies etc. The nanomolar concentrations of cerium oxide nanoparticles were also found to be useful in decreasing ROS (reactive oxygen species) mediated cellular damages in various in vitro cell cultures. Cerium oxide nanoparticles reduced the cellular damages to the normal breast epithelial cell line (CRL 8798) induced by X-rays and to the Keratinocyte cell line induced by UV irradiation. Cerium oxide nanoparticles were also found to be neuroprotective to adult rat spinal cord and retinal neurons. We propose that cerium oxide nanoparticles act as free radical scavenger (via redox reactions on its surface) to decrease the ROS induced cellular damages. Additionally, UV-visible spectroscopic studies indicated that cerium oxide nanoparticles possess auto-regenerative property by switching its oxidation state between Ce3+ and Ce4+. The auto-regenerative antioxidant property of these nanoparticles appears to be a key component in all the biological applications discussed in the present study.

Yes / This paper aims to evaluate the influence of surface area and amount of nano silica (NS) on the performance of concrete with different water/binder (w/b) ratios. For this purpose, 63 different mixes were produced using three NS having three differentsurface areas (52, 250 and 500 m2/g) and w/b ratios (0.4, 0.5 and 0.6). Compressive strengths , workability, water absorption and the microstrcture of concrete mixtures were measured and analysed. and the optimum ratio for each type was determined. The results indicated that the performance of NS particles in concrete is significantly dependent on its amount and surface area as well as w/b ratio. As the w/b ratio increased, a better performance was observed for all types of NS used, whilst NS having 250m2/g surface area was found to be the most effective. The optimum amount of NS ranged from 2 to 5%, depending on NS surface area. / The full-text of this article will be released for public view at the end of the publisher embargo on 15 May 2020.