Phasor Measurement Units (PMUs) are widely acknowledged as one of the most significant developments in the field of real-time monitoring of power system. By aligning time stamps of voltage and current phasor measurements, which are consistent with Coordinated Universal Time (UTC), a coherent picture of the power system state can be achieved through either direct measurements or simple linear calculations. With the growing number of PMUs installed or planned to be installed in the near future, both utilities and research institutions are looking for novel applications of synchrophasor measurements from these widely installed PMUs. In this dissertation, the author proposes two new PMUs measurements applications: three-phase instrument transformer calibration, and three-phase line parameter calculation with instrument transformers. First application is to calibrate instrument transformers. Instrument transformers are the main sensors used in power systems. They provide isolation between high voltage level of primary side and metering level of the secondary side. All the monitoring and measuring systems obtain input signals from the secondary side of instrument transformers. That means when instrument transformers are not accurate, all the measurements used in power system are inaccurate. The most important job of this dissertation is to explore a method to automatically calibrate all the instrument transformers in the power system based on real-time synchrophasor measurements. The regular instrument transformer calibration method requires the instrument transformer to be out of service (offline) and calibrated by technicians manually. However, the error of instrument transformer changes when environment changes, and connected burden. Therefore, utilities are supposed to periodically calibrate instrument transformers at least once a year. The high labor and economic costs make traditional instrument transformer calibration method become one of the urgent problems in power industry. In this dissertation we introduce a novel, low cost and easy method to calibrate three-phase instrument transformers. This method only requires one three-phase voltage transformer at one bus calibrated in advance. All other instrument transformers can be calibrated by this method as often as twice a day, based on the synchrophasor measurements under different load scenarios. Second application is to calculate line parameters during calibrating instrument transformers. The line parameters, line impedance and line shunt admittance, as needed by utilities are generated by the computer method. The computer method is based on parameters, such as the diameter, length, material characteristics, the distance among transmission line, the distance to ground and so on. The formulas to calculate line parameters have been improved and re-modeled from time to time in order to increase the accuracy. However, in this case, the line parameters are still inaccurate due to various reasons. The line parameters errors do affect the instrument transformers calibration results (with 5% to 10% error). To solve this problem, we present a new method to calculate line parameters and instrument transformers in the same processing step. This method to calibrate line parameter and instrument transformers at the same time only needs one pre-calibrated voltage transformer and one pre-calibrated current transformer in power system. With the pre-calibrated instrument transformers, the line parameter as well as the ratio correction factors of all the other instrument transformers can be solved automatically. Simulation results showed the errors between calculated line parameters and the real line parameter, the errors between calibrated ratio correction factors and the real ratio correction factors are of the order of 10e-10 per unit. Therefore, high accuracy line parameters as well as perfectly calibrated instrument transformers can be obtained by this new method. This method can run automatically every day. High accuracy and dynamic line parameters will significantly improve power system models. It will also increase the reliability and speed of the relay system, enhance the accuracy of power system analysis, and benefit all other researches using line parameters. New methods of calculating line parameter and the instrument transformer calibrations will influence the whole power industry significantly. / Ph. D.

This work starts from the proposition that it is beneficial to conserve communication energy in Wireless Sensor Networks (WSNs). For WSNs there is an added incentive for energy-efficient communication. The power supply of a sensor is often finite and small. Replenishing the power may be impractical and is likely to be costly. Wireless Sensor Networks are an important area of research. Data about the physical environment may be collected from hostile or friendly environments. Data is then transmitted to a destination without the need for communication cables. There are power and resource constraints upon WSNs, in addition WSN networks are often application specific. Different applications will often have different requirements. Further, WSNs are a shared medium system. The features of the MAC (Medium Access Control) protocol together with the application behaviour shape the communication states of the node. As each of these states have different power requirements the MAC protocol impacts upon the operation and power consumption efficiency. This work focuses on the development of an energy conservation protocol for WSNs where direct communication between sources and a base station is feasible. Whilst the multi-hop approach has been regarded as the underlying communication paradigm in WSNs, there are some scenarios where direct communication is applicable and a significant amount of communication energy can be saved. The Power & Reliability Aware Protocol has been developed. Its main objectives are to provide efficient data communication by means of energy conservation without sacrificing required reliability. This has been achieved by using direct communication, adaptive power adaptation and intelligent scheduling. The results of simulations illustrate the significance of communication energy and adaptive transmission. The relationship between Received Signal Strength Indicator (RSSI) and Packet Reception Rate (PRR) metrics is established and used to identify when power adaptation is required. The experimental results demonstrate an optimal region where lower power can be used without further reduction in the PRR. Communication delays depend upon the packet size whilst two-way propagation delay is very small. Accurate scheduling is achieved through monitoring the clock drift. A set of experiments were carried out to study benefits of direct vs. multi-hop communication. Significant transmitting current can be conserved if the direct communication is used. PoRAP is compared to Sensor-MAC (S-MAC), Berkeley-MAC (B-MAC) and Carrier Sense Multiple Access (CSMA). Parameter settings used in the Great Duck Island (GDI) a production habitat monitoring WSNs were applied. PoRAP consumes the least amount of energy.

Digitizing analog meters into the IoT where meters can be read remotely is a solution which is both environmentally and economically beneficial. This study investigate show energy critical systems can gain a longer lifespan by optimizing their energy consumption. The purpose of this study is to evaluate the energy consumption of energy critical systems with different wireless data transfer protocols. This is conducted with experiments and observations.The data was collected by setting up two testbeds where the wireless transmission interfaces WiFi and BLE were used to send data between two microcomputers. These testbeds measured the energy consumption when altering with the variables of the two transmission protocols.The result shows that the internal protocols of WiFi were greatly affected by the changes made in the variables compared to BLE during the experiments. The results also show that when calibrating the different variables, the energy consumption is reduced by up around 52%. Furthermore, the result indicates that there is energy to saveif you optimize transmission power to a specific environment.In this study, BLE has little to no change to the energy consumption when changing the different variables. When investigating the internal protocols of WiFi, they are greatly affected by the different variables being changed. A lower transmission power can be more energy efficient but at the cost of shorter range and eventually a higher packet loss.

No description available.

Network lifetime is an important performance metric in Wireless Sensor Networks (WSNs). Transmission Power Control (TPC) is a well-established method to minimise energy consumption in transmission in order to extend node lifetime and, consequently, lead to solutions that help extend network lifetime. The accurate lifetime estimation of sensor nodes is useful for routing to make more energy-efficient decisions and prolong lifetime. This research proposes an Energy-Efficient TPC (EETPC) mechanism using the measured Received Signal Strength (RSS) to calculate the ideal transmission power. This includes the investigation of the impact factors on RSS, such as distance, height above ground, multipath environment, the capability of node, noise and interference, and temperature. Furthermore, a Dynamic Node Lifetime Estimation (DNLE) technique for WSNs is also presented, including the impact factors on node lifetime, such as battery type, model, brand, self-discharge, discharge rate, age, charge cycles, and temperature. In addition, an Energy-Efficient and Lifetime Aware Routing (EELAR) algorithm is designed and developed for prolonging network lifetime in multihop WSNs. The proposed routing algorithm includes transmission power and lifetime metrics for path selection in addition to the Expected Transmission Count (ETX) metric. Both simulation and real hardware testbed experiments are used to verify the effectiveness of the proposed schemes. The simulation experiments run on the AVRORA simulator for two hardware platforms: Mica2 and MicaZ. The testbed experiments run on two real hardware platforms: the N740 NanoSensor and Mica2. The corresponding implementations are on two operating systems: Contiki and TinyOS. The proposed TPC mechanism covers those investigated factors and gives an overall performance better than the existing techniques, i.e. it gives lower packet loss and power consumption rates, while delays do not significantly increase. It can be applied for single-hop with multihoming and multihop networks. Using the DNLE technique, node lifetime can be predicted more accurately, which can be applied for both static and dynamic loads. EELAR gives the best performance on packet loss rate, average node lifetime and network lifetime compared to the other algorithms and no significant difference is found between each algorithm with the packet delay.

In the past decade, the development of wireless communication technologies has made the use of the Internet ubiquitous. With the increasing number of new inventions and applications using wireless communication, more interference is introduced among wireless devices that results in limiting the capacity of wireless networks. Many approaches have been proposed to improve the capacity. One approach is to exploit multiple channels by allowing concurrent transmissions, and therefore it can provide high capacity. Many available, license-exempt, and non-overlapping channels are the main advantages of using this approach. Another approach that increases the network capacity is to adjust the transmission power; hence, it reduces interference among devices and increases the spatial reuse. Integrating both approaches provides further capacity. However, without careful transmission power control (TPC) design, the network performance is limited. The first part of this thesis tackles the integration to efficiently use multiple channels with an effective TPC design in a distributed manner. We examine the deficiency of uncontrolled asymmetrical transmission power in multi-channel ad hoc wireless networks. To overcome this deficiency, we propose a novel distributed transmission power control protocol called the distributed power level (DPL) protocol for multi-channel ad hoc wireless networks. DPL allocates different maximum allowable power values to different channels so that the nodes that require higher transmission power are separated from interfering with the nodes that require lower transmission power. As a result, nodes select their channels based on their minimum required transmission power to reduce interference over the channels. We also introduce two TPC modes for the DPL protocol: symmetrical and asymmetrical. For the symmetrical mode, nodes transmit at the power that has been assigned to the selected channel, thereby creating symmetrical links over any channel. The asymmetrical mode, on the other hand, allows nodes to transmit at a power that can be lower than or equal to the power assigned to the selected channel. In the second part of this thesis, we propose the multi-channel MAC protocol with hopping reservation (MMAC-HR) for multi-hop ad hoc networks to overcome the multi-channel exposed terminal problem, which leads to poor channel utilization over multiple channels. The proposed protocol is distributed, does not require clock synchronization, and fully supports broadcasting information. In addition, MMAC-HR does not require nodes to monitor the control channel in order to determine whether or not data channels are idle; instead, MMAC-HR employs carrier sensing and independent slow channel hopping without exchanging information to reduce the overhead. In the last part of this thesis, a novel multi-channel MAC protocol is developed without requiring any change to the IEEE 802.11 standard known as the dynamic switching protocol (DSP) based on the parallel rendezvous approach. DSP utilizes the available channels by allowing multiple transmissions at the same time and avoids congestion because it does not need a dedicated control channel and enables nodes dynamically switch among channels. Specifically, DSP employs two half-duplex interfaces: One interface follows fast hopping and the other one follows slow hopping. The fast hopping interface is used primarily for transmission and the slow hopping interface is used generally for reception. Moreover, the slow hopping interface never deviates from its default hopping sequence to avoid the busy receiver problem. Under single-hop ad hoc environments, an analytical model is developed and validated. The maximum saturation throughput and theoretical throughput upper limit of the proposed protocol are also obtained.

Μέχρι σήμερα στη δρομολόγηση στα ασύρματα αδόμητα δίκτυα λαμβάνεται ως κριτήριο ένα μοναδιαίο μέγεθος για κάθε σύνδεσμο του δικτύου, το οποίο αναπαριστά το κόστος της μετάδοσης πάνω στον συγκεκριμένο σύνδεσμο. Στη δρομολόγηση με βάση πολλαπλά κριτήρια η βασική ιδέα είναι ότι σε κάθε σύνδεσμο ανατίθεται ένα διάνυσμα από παραμέτρους-κόστη με βάση το οποίο προκύπτει και ένα αντίστοιχο διάνυσμα για κάθε μονοπάτι. Για κάθε ζευγάρι κόμβων αποστολέα-παραλήπτη γίνεται καταρχήν η εύρεση όλων των υποψήφιων για χρήση μονοπατιών. Τα υποψήφια μονοπάτια, που λαμβάνονται υπόψη κατά τη διαδικασία επιλογής, έχουν την ιδιότητα να είναι μη-κυριαρχημένα μεταξύ τους. Στη συνέχεια εφαρμόζεται στο σύνολο των μη-κυριαρχημένων μονοπατιών μια συνάρτηση που συνδυάζοντας τις συνιστώσες του κάθε διανύσματος παράγει το κόστος χρήσης κάθε μονοπατιού και έτσι το μονοπάτι με το ελάχιστο κόστος επιλέγεται για χρήση. Στα πλαίσια της εργασίας, καταρχήν μελετήθηκε ο αλγόριθμος δρομολόγησης με πολλαπλά κόστη χρησιμοποιώντας παραμέτρους-κόστη σχετικές με την ενέργεια, όπως η τρέχουσα διαθέσιμη ενέργεια στους κόμβους και η ισχύς μετάδοσής τους. Στη συνέχεια στις παραμέτρους προστέθηκε και η παρεμβολή που δημιουργείται από τη μετάδοση πάνω σε ένα σύνδεσμο. Τα αποτελέσματα των προσομοιώσεων έδειξαν ότι ο αλγόριθμος δρομολόγησης με πολλαπλά κόστη, σε σχέση με τον ελάχιστου μήκους διαδρομής, κατανέμει πιο ομοιόμορφα την κίνηση στο δίκτυο, επιμηκύνει τον χρόνο ζωής του δικτύου και αυξάνει το ποσοστό των παραδιδόμενων πακέτων. Στο επόμενο στάδιο της εργασίας έγινε μια κατανεμημένη υλοποίηση του αλγορίθμου δρομολόγησης με πολλαπλά κόστη, που επιπλέον λαμβάνει υπόψη την κινητικότητα των κόμβων του δικτύου, η οποία και πάλι φάνηκε να υπερέχει έναντι πιο παραδοσιακών πρακτικών. Τέλος η ιδέα της δρομολόγησης με πολλαπλά κόστη εφαρμόστηκε για τη λύση του προβλήματος ενεργο-αποδοτικής πολλαπλής ή ολικής εκπομπής (multicasting ή broadcasting, αντίστοιχα). Στόχος ήταν να βρεθεί η βέλτιστη ενεργο-αποδοτικά ακολουθία συνδέσμων πάνω στους οποίους πρέπει να γίνει μετάδοση ενός πακέτου προκειμένου να υλοποιηθεί η επιθυμητή εκπομπή. Σαν παράμετροι-κόστη χρησιμοποιήθηκαν η τρέχουσα διαθέσιμη ενέργεια και η ισχύς μετάδοσης των κόμβων. Τα αποτελέσματα δείχνουν σαφή υπεροχή του αλγορίθμου με πολλαπλά κόστη έναντι παραδοσιακών λύσεων τόσο για πολλαπλή εκπομπή όσο και για ολική εκπομπή. / Until now, routing in wireless ad hoc networks has been studied by taking into account a single scalar metric for every network link, representing the cost of transmitting through this link. In multicost routing a vector of cost parameters is assigned to each link, based on which a respective cost vector is produced for every path in the network. For every source-destination pair all the candidate paths are initially calculated that are non-dominated to each other. At the cost vectors of the candidate paths, an optimization function is applied in order to produce a cost for each path based on which the selection of the optimal one is made. In the present thesis multicost routing in wireless ad hoc networks was studied initially using as cost parameters the node residual energy and transmission power. As a next step the interference cause by the transmission of each link was added to the cost vectors assigned to each network link. The simulation results showed that multicost routing in comparison to traditional routing practices achieves more uniform traffic distribution and energy consumption in the network, prolongs the network lifetime and increases the percentage of the packets that are successfully delivered to their destinations. Expanding these ideas, the multicost routing algorithm was next implemented in a fully distributed fashion in which additionally the node mobility was taken into account. The results again proved that a significant improvement was accomplished compared to minimum-hop routing. Finally, multicost routing was applied in the field of multicasting and broadcasting in wireless ad hoc networks. The emphasis was again on energy-efficiency by incorporating energy-related cost parameters like node residual energy and transmission power. The multicost algorithm calculates the optimal energy-efficient sequence of nodes that by transmitting implement the desired communication task (multicasting or broadcasting). Simulation results illustrate a clear advantage of our algorithm over established solutions for energy-efficient multicasting and broadcasting.

The remarkable evolution of wireless networks into the next generation to provide ubiquitous and seamless broadband applications has recently triggered the emergence of Wireless Mesh Networks (WMNs). The WMNs comprise stationary Wireless Mesh Routers (WMRs) forming Wireless Backbone Mesh Networks (WBMNs) and mobile Wireless Mesh Clients (WMCs) forming the WMN access. While WMCs are limited in function and radio resources, the WMRs are expected to support heavy duty applications : that is, WMRs have gateway and bridge functions to integrate WMNs with other networks such as the Internet, cellular, IEEE 802.11, IEEE 802.15, IEEE 802.16, sensor networks, et cetera. Consequently, WMRs are constructed from fast switching radios or multiple radio devices operating on multiple frequency channels. WMRs are expected to be self-organized, self-configured and constitute a reliable and robust WBMN which needs to sustain high traffic volumes and long "online" time. However, meeting such stringent service expectations requires the development of decentralized dynamic transmission power control (DTPC) approaches. This thesis addresses the DTPC problem for both single and multiple channel WBMNs. For single channel networks, the problem is formulated as the minimization of both the link-centric and network-centric convex cost function. In order to solve this issue, multiple access transmission aware (MATA) models and algorithms are proposed. For multi-radio multi-channel (MRMC) WBMNs, the network is modelled as sets of unified channel graphs (UCGs), each consisting of interconnected active network users communicating on the same frequency channel. For each UCG set, the minimization of stochastic quadratic cost functions are developed subject to the dynamic Link State Information (LSI) equations from all UCGs. An energy-efficient multi-radio unification protocol (PMMUP) is then suggested at the Link-Layer (LL). Predictive estimation algorithms based on this protocol are proposed to solve such objective functions. To address transmission energy and packet instabilities, and interference across multiple channels, singularly-perturbed weakly-coupled (SPWC) control problems are formulated. In order to solve the SPWC transmission power control problem, a generalized higher-order recursive algorithm (HORA) that obtains the Riccati Stabilizing Solutions to the control problem is developed. The performance behaviours of the proposed models and algorithms are evaluated both analytically and through computer simulations. Several simulations are performed on a large number of randomly generated topologies. Simulation and analytical results confirm the efficacy of the proposed algorithms compared to the most recently studied techniques

In the past decade, the development of wireless communication technologies has made the use of the Internet ubiquitous. With the increasing number of new inventions and applications using wireless communication, more interference is introduced among wireless devices that results in limiting the capacity of wireless networks. Many approaches have been proposed to improve the capacity. One approach is to exploit multiple channels by allowing concurrent transmissions, and therefore it can provide high capacity. Many available, license-exempt, and non-overlapping channels are the main advantages of using this approach. Another approach that increases the network capacity is to adjust the transmission power; hence, it reduces interference among devices and increases the spatial reuse. Integrating both approaches provides further capacity. However, without careful transmission power control (TPC) design, the network performance is limited. The first part of this thesis tackles the integration to efficiently use multiple channels with an effective TPC design in a distributed manner. We examine the deficiency of uncontrolled asymmetrical transmission power in multi-channel ad hoc wireless networks. To overcome this deficiency, we propose a novel distributed transmission power control protocol called the distributed power level (DPL) protocol for multi-channel ad hoc wireless networks. DPL allocates different maximum allowable power values to different channels so that the nodes that require higher transmission power are separated from interfering with the nodes that require lower transmission power. As a result, nodes select their channels based on their minimum required transmission power to reduce interference over the channels. We also introduce two TPC modes for the DPL protocol: symmetrical and asymmetrical. For the symmetrical mode, nodes transmit at the power that has been assigned to the selected channel, thereby creating symmetrical links over any channel. The asymmetrical mode, on the other hand, allows nodes to transmit at a power that can be lower than or equal to the power assigned to the selected channel. In the second part of this thesis, we propose the multi-channel MAC protocol with hopping reservation (MMAC-HR) for multi-hop ad hoc networks to overcome the multi-channel exposed terminal problem, which leads to poor channel utilization over multiple channels. The proposed protocol is distributed, does not require clock synchronization, and fully supports broadcasting information. In addition, MMAC-HR does not require nodes to monitor the control channel in order to determine whether or not data channels are idle; instead, MMAC-HR employs carrier sensing and independent slow channel hopping without exchanging information to reduce the overhead. In the last part of this thesis, a novel multi-channel MAC protocol is developed without requiring any change to the IEEE 802.11 standard known as the dynamic switching protocol (DSP) based on the parallel rendezvous approach. DSP utilizes the available channels by allowing multiple transmissions at the same time and avoids congestion because it does not need a dedicated control channel and enables nodes dynamically switch among channels. Specifically, DSP employs two half-duplex interfaces: One interface follows fast hopping and the other one follows slow hopping. The fast hopping interface is used primarily for transmission and the slow hopping interface is used generally for reception. Moreover, the slow hopping interface never deviates from its default hopping sequence to avoid the busy receiver problem. Under single-hop ad hoc environments, an analytical model is developed and validated. The maximum saturation throughput and theoretical throughput upper limit of the proposed protocol are also obtained.

[pt] As redes de sensores sem fio se constituem numa área que outorga grandes oportunidades para a oferta de uma série de aplicações inovadoras e com baixo custo. Os dispositivos destas redes são bastantes pequenos e sua fonte de alimentação são baterias. O tempo de vida destas é limitado, limitando assim o tempo da vida dos sensores e da rede como um todo. Por esta razão nos últimos anos o tema de eficiência energética tem atraído grande interesse de pesquisadores. O aumento do custo da energia e do consumo global da energia pelo setor de ICT (Information and Communications Technologies) têm crescido vertiginosamente devido ao aumento continuo do número de clientes e da demanda por aplicações de maior complexidade. Por tudo isso têm sido desenvolvidos distintos métodos e técnicas para economizar energia nas RSSF. Neste trabalho se implementam dois algoritmos que levam em conta critérios para economizar os custos de energia da rede e através de experimentos de simulação se avalia os mesmos. Nos resultados pode se observar as vantagens de trabalhar com sistemas que visam a eficiência energética. / [en] The WSNs (Wireless Sensor Networks) belong to an area that gives rise to great opportunities to spread innovative and low cost applications. These kinds of networks are composed of tiny devices with limited energy. The main source of power supply for WSNs are batteries, which are limited in cycle life, thus limiting the sensors lifetime and the network as a whole. Due to that fact, the energy efficiency network is becoming the main concern to be addressed by researchers. Rising energy prices and global energy consumption by the ICT (Information and Communications Technologies) sector have grown dramatically due to the continuous increase in customer number and the demand for more complex applications. For the reasons outlined above, different energy-saving techniques for WSNs have been developed. Two energy-saving algorithms for WSNs were implemented in this thesis, and they were tested by experimental evaluation using simulation. The results obtained from the simulations showed the advantages of working with systems aiming at energy efficiency.