This thesis evaluates a particular ultrasonic nondestructive testing (NDT) system in order to determine its capabilities and limitations in locating defects in concrete structures; specifically tunnel linings, bridge decks, and pavements. The device, a phased-array ultrasonic tomography (UST) system that utilizes shear waves, is a significant advancement in NDT systems. Consequently, there is a need in structural engineering to verify new technologies by assessing their flaw-detecting capabilities in a variety of structural applications. The UST technique does not currently have a testing methodology that is field-ready. In order to develop a methodology, the system was evaluated based on its ability to detect simulated defects, then taken to the field to evaluate natural structural defects on public tunnels, pavements, and airport runways. Types of concrete defects the system is used to detect and localize include air- and water-filled voids, vertical cracks, horizontal delaminations, and abnormalities such as clay lumps. The device is also used to determine reinforcement depth and spacing as well as concrete thickness measurements. This research concludes that the UST system is exceptional at locating horizontal delaminations ranging from 0.05-2.0 mm (0.002-0.079 in.), and is able to differentiate between fully debonded and partially-bonded areas. Vertical cracks could only be detected once they begin to form parallel to the testing surface; however, omission of surface details was found to be a strong indicator of crack presence. Backwall surfaces up to a depth of 762 mm (30 in.) were successfully and accurately determined. Air- and water-filled voids as well as reinforcement details such as layout and depth were also successfully determined and located. With the exception of some medium-sized clay lumps (with a diameter of approximately 102 mm, or 4 in.) surrounding reinforcement, all clay lumps tested were also highly successful.

This thesis is concerned with the modeling of the stator of a piezoelectric traveling wave rotary ultrasonic motor. Existing models for piezoelectric traveling wave rotary ultrasonic motors are either too complicated to be used in motor control or do not reflect the real behavior of the motor and are of limited use in developing a controller for the motor. Finite Element methods have been used in the past to examine the properties of piezoelectric structures however, the Finite Volume Method has always been ruled out without justification. The main goal of this thesis is to provide a Finite Volume modeling approach for the stator of the piezoelectric traveling wave rotary ultrasonic motor taking into account the basic theoretical principles from piezoelectricity and structural mechanics. This model can in future be extended to develop a complete model of the motor in addition to other piezoelectric structures. The Finite Volume Method is shown to have the following specific advantages over the Finite Element Method especially for structures with simple geometries: 1. the Finite Volume Method respects the PDEs conservation law structure due to the fact that the fluxes are conserved between cells/domains/subregions, 2. the Finite Volume Method involves only surface integrals thus making it easier to implement a rotor-stator contact model as the contact mechanism occurs at the boundary of the stator, and 3. the Finite Volume Method yields a system of ODEs that more intuitively map onto circuit simulation software. The Finite Volume Method is initially used to model a simple piezoelectric plate. A corresponding circuit of the piezoelectric plate model, based on the Finite Volume Method, is generated. Two additional but more complex models are considered: one for a unimorph plate and one for the stator of an ultrasonic motor. The modeling results obtained with the Finite Volume Method are validated by comparing them with the results obtained with Finite Element simulations performed with COMSOL. Two test platforms designed to test and validate the Finite Volume and COMSOL results for the simple piezoelectric plates and piezoelectric traveling wave rotary ultrasonic motors are also presented in this thesis.

This thesis is concerned with the modeling of the stator of a piezoelectric traveling wave rotary ultrasonic motor. Existing models for piezoelectric traveling wave rotary ultrasonic motors are either too complicated to be used in motor control or do not reflect the real behavior of the motor and are of limited use in developing a controller for the motor. Finite Element methods have been used in the past to examine the properties of piezoelectric structures however, the Finite Volume Method has always been ruled out without justification. The main goal of this thesis is to provide a Finite Volume modeling approach for the stator of the piezoelectric traveling wave rotary ultrasonic motor taking into account the basic theoretical principles from piezoelectricity and structural mechanics. This model can in future be extended to develop a complete model of the motor in addition to other piezoelectric structures. The Finite Volume Method is shown to have the following specific advantages over the Finite Element Method especially for structures with simple geometries: 1. the Finite Volume Method respects the PDEs conservation law structure due to the fact that the fluxes are conserved between cells/domains/subregions, 2. the Finite Volume Method involves only surface integrals thus making it easier to implement a rotor-stator contact model as the contact mechanism occurs at the boundary of the stator, and 3. the Finite Volume Method yields a system of ODEs that more intuitively map onto circuit simulation software. The Finite Volume Method is initially used to model a simple piezoelectric plate. A corresponding circuit of the piezoelectric plate model, based on the Finite Volume Method, is generated. Two additional but more complex models are considered: one for a unimorph plate and one for the stator of an ultrasonic motor. The modeling results obtained with the Finite Volume Method are validated by comparing them with the results obtained with Finite Element simulations performed with COMSOL. Two test platforms designed to test and validate the Finite Volume and COMSOL results for the simple piezoelectric plates and piezoelectric traveling wave rotary ultrasonic motors are also presented in this thesis.

Background and aims: It is known that smooth muscle possesses substantial mechanical plasticity in that it is able to adapt to large changes in length without compromising its ability to generate force. It is believed that structural malleability of the contractile apparatus underlies this plasticity. There is strong evidence suggesting that myosin thick filaments of the muscle are relatively labile and their length in vivo is determined by the equilibrium between monomeric and filamentous myosin. The equilibrium in turn is governed by the state of phosphorylation of the 20-kD regulatory myosin light chain (MLC20, or RLC). It is known that phosphorylation of the myosin light chain favors formation of the filaments; it is not known how the light chain phosphorylation affects the lability of the filaments. The major aim of this thesis was to measure the mechanical integrity of the filaments formed from purified myosin molecules from bovine airway smooth muscle, and to determine whether the integrity was influenced by phosphorylation of the myosin light chain. Methods: Myosin was purified from bovine trachealis to form filaments, in ATP containing zero-calcium solution during a slow dialysis that gradually reduced the ionic strength. Sufficient myosin light chain kinase and phosphatase, as well as calmodulin, were retained after the myosin purification and this enabled phosphorylation of RLC within 20-40 s after addition of calcium to the filament suspension. The phosphorylated and non-phosphorylated filaments were then partially disassembled by ultrasonification. The extent of filament disintegration was visualized and quantified by atomic force microscopy. Results: RLC phosphorylation reduced the diameter of the filaments and rendered the filaments more resistant to ultrasonic agitation. Electron microscopy revealed a similar reduction in filament diameter in intact smooth muscle when the cells were activated. Conclusion: Our results suggest that RLC phosphorylation is a key regulatory step in modifying the structural properties of myosin filaments in smooth muscle, where formation and dissolution of the filaments are required in the cells’ adaptation to different cell length.

Ultrasonic anemometer (UA) is a core application in natural environment measurement. As well known, mechanical anemometer works well in good weather but it is not suitable to be applied in bad environment such as polar region and upper air. On the other hand, ultrasonic anemometer works well in most situations. Moreover, ultrasonic anemometer has wider detectable wind speed range. It can be said that ultrasonic anemometer is a more advanced instrument to measure wind velocity. In this paper, the theory of ultrasonic anemometer is first discussed. Using the theory, a test bed is then designed and constructed to measure one-dimensional wind speed. Active Butterworth filter is introduced into the circuit in order to increase the stability and accuracy. Furthermore, we test the one-dimensional ultrasonic anemometer and compare the measured wind speed with theoretical wind speed measured by a thermal anemometer device. Error is also discussed and improvement has also made during the experiment.

This report is the result of a master thesis work where the goal was to develop acontrol system for a type of ultrasonic motor. The ultrasonic motors use ultrasonicvibrations from a piezoelectric material to produce a rotating motion. They arepowered by two sinusoidal voltages and their control signals generally are thevoltages amplitude, frequency and the phase difference between the two voltages.In this work the focus is on control using only amplitude and frequency. A feedbacksignal was provided by an encoder, giving an angular position. The behavior of themotors were investigated for various sets of control signals. From collected data alinearized static model was derived for the motor speed. This derived model wasused to create a two part control system, with an inner control loop to managethe speed of the motors using a PI controller and an outer control loop to managethe position of the motors. A simple algorithm was used for the position controland the result was a control system able to position the motors with a 0.1 degreeaccuracy. The motors show potential for greater accuracy with a position feedback,but the result in this work is limited by the encoder used in the experiments.

No description available.

Presented in this thesis are two studies that apply nondestructive testing methods to civil engineering problems. The first study examines the relationship between the small-strain and large-strain properties of exhumed cast iron water pipes. Nondestructive and destructive testing programs were performed on eight pipes varying in age from 40 to 130 years. New applications of frequency domain analysis techniques including Fourier and wavelet transforms of ultrasonic pulse velocity measurements are presented. The effects of Lamb wave propagation on the ultrasonic testing results are investigated. Microstructure evaluation revealed two different types of cast iron within the pipes sampled: grey cast iron and ductile iron. A low correlation between wave propagation and large-strain measurements was observed. However, the wave velocities were consistently different between ductile and grey cast iron pipes (14% to 18% difference). Lamb waves were found to contribute significantly to the frequency content of the ultrasonic signals possibly resulting in the poor correlations observed. Therefore, correlations between wave velocities and large strain properties obtained using samples from exhumed water pipes must be used with caution in the condition assessment of aged water pipes especially for grey cast iron pipes. The second study presented in this thesis was performed to evaluate the effectiveness of three geophysical methods for geotechnical site characterization in swamps and environmentally sensitive wetland areas. The geophysical methods evaluated were electrical resistivity imaging (ERI), seismic refraction (SR), and multiple-channel analysis of surface waves (MASW). The geophysical test results were verified against the results from borehole and CPT logs. The ERI results were best for determining the depth to the glacial till. The SR results overestimated the depth to the till because of the presence of a stiffness reversal. The MASW results predicted the depth to the refusal till layer less accurately than the ERI method. However, this method was able to detect the three distinct layers above the till. These methods can be used as a basis for further development to optimize a procedure to reduce the number of boreholes required for conventional site investigations in areas that are environmentally sensitive or where access is restricted.

Laser ultrasonics has been used to measure the bending stiffness of paper products by measuring the dispersion of ultrasonic plate waves. In laser ultrasonics, ultrasound can be generated by absorption of pulsed laser spot while detection can be carried out by Laser Doppler Interferometry. The research presented in this paper describes a new method to detect ultrasonic plate waves using a recently developed acoustic transducer, more specifically an optical Micro ElectroMechanical System (MEMS) microphone with broadband capability. The MEMS device operates as a non-contact proximity probe placed less than ¼ a millimeter away from the plate. The signals are detected with a capacitive micromachined ultrasonic transducer (cMUT) in which the back electrode of the capacitive transducer on a transparent substrate is shaped as an optical diffraction grating. The displacement of the transducer membrane is determined using an optical interferometer. By applying voltage to deflect the membrane electrostatically, the detection sensitivity is kept at an optimum level. The main purpose of the research presented herein was to test this MEMSs ability to detect ultrasonic waves propagating through paper, to increase the signal-to-noise ratio (SNR), and to calibrate the device in order to quantify the limitations on sensitivity in the context of the detection of ultrasound in paper. Similar tests were conducted for comparison with a modified Mach-Zehnder Interferometer, a more traditional method used for laser ultrasonic detection, and its results are presented in this paper.

No description available.