Because of its potential application for flat panel displays, solid-state lighting and 1.5 µm emitter for fiber optical communications, organic light-emitting diodes (OLEDs) have been intensively researched. One of the major problems with current OLED technology relates to inefficient electron injection at the cathode interface, which causes high driving voltage and poor device stability. Making a low resistance cathode contact for electron injection is critical to device performance. This work mainly focuses on cathode interface design and engineering. The Ohmic contact using a structure of C60/LiF/Al has been developed in electron only devices. It is found that application of the C60/LiF/Al contact to Alq based OLEDs leads to a dramatic reduction in driving voltages, a significant improvement in power efficiency, and a much slower aging process. A new cathode structure based on metal-organic-metal (MOM) tri-layer films has been developed. It is found that MOM cathodes reduce reflection by deconstructive optical interference from two metal films. The absolute reflectance from the MOM tri-layer films can be reduced to as low as 7% in the visible light spectrum. In actual working devices, the reflectance can be reduced from ~80% to ~ 20%. MOM cathodes provide a potential low-cost solution for high contrast full-color OLED displays. Low voltage Erq based OLEDs at 1.5 µm emission have been developed. The Erq/Ag cathode interface has been found to be efficient for electron injection. Dramatic improvement in driving voltage and power efficiency has been realized by implementing Bphen and C60 into Erq devices as an electron transport layer. Integration of Erq devices on Si wafers has also been demonstrated.

Multijunction solar cells made from a combination of CQDs of differing sizes and thus bandgaps are a promising means by which to increase the energy harvested from the Sun’s broad spectrum. In this dissertation, we first report the systematic engineering of 1.6 eV PbS CQD solar cells, optimal as the front cell responsible for visible wavelength harvesting in tandem photovoltaics. We rationally optimize each of the device’s collecting electrodes—the heterointerface with electron accepting TiO2 and the deep-work-function hole-collecting MoO3 for ohmic contact—for maximum efficiency. Room-temperature processing enables flexible substrates, and permits tandem solar cells that integrate a small-bandgap back cell atop a low thermal-budget larger-bandgap front cell. We report an electrode strategy that enables a depleted heterojunction CQD PV device to be fabricated entirely at room temperature. We develop a two-layer donor-supply electrode (DSE) in which a highly doped, shallow work function layer supplies a high density of free electrons to an ultrathin TiO2 layer via charge-transfer doping. Using the DSE we build all-room-temperature-processed small-bandgap (1 eV) colloidal quantum dot solar cells suitable for use as the back junction in tandem solar cells. We further report in this work the first efficient CQD tandem solar cells. We use a graded recombination layer (GRL) to provide a progression of work functions from the hole-accepting electrode in the bottom cell to the electron-accepting electrode in the top cell. The recombination layers must allow the hole current from one cell to recombine, with high efficiency and low voltage loss, with the electron current from the next cell. We conclude our dissertation by presenting the generalized conditions for design of efficient graded recombination layer solar devices. We demonstrate a family of new GRL designs experimentally and highlight the benefits of the progression of dopings and work functions in the interlayers.

Organic semiconductors have the advantage over traditional inorganic semiconductors, such as Si or GaAs, in that they do not require perfect single crystal films to operate in real devices. Complicated multi-layer structures with nanometer scale thicknesses can thus be easily fabricated from organic materials using low-cost roll-to-roll manufacturing techniques. However, the discrete nature of organic semiconductors also implies that they typically contain almost no intrinsic charge carriers (i.e., electrons or holes), and thus act as insulators until electrical charges are injected into them. In electrical device applications this means that all of the holes and electrons within a device must be injected from the anode and cathode respectively. As a result, device stability, performance, and lifetime are greatly influenced by the interface between the organic materials and the electrode contacts. Despite the fundamental importance of the electrode/organic contacts, much of the basic physical understanding of these interfaces remains unclear. As a result, the current design of state-of-the-art organic optoelectronic devices tends to be based on trial and error experimentation, resulting in overly complicated structures that are less than optimal. In the present thesis, various electrode/organic interfaces relevant to device applications are studied using a variety of different techniques, including photoelectron spectroscopy and the iii temperature dependent current-voltage characteristics of single carrier devices. The fundamental understanding gleaned from these studies has been used to develop new strategies for controlling the energy-level alignment at electrode/organic interfaces. A universal method for tuning the work function of electrode materials using a halogenated organic solvent and UV light has been developed. Application of this technique in organic light emitting diodes enabled the first highly simplified two-layer device with a state-of-the-art record breaking efficiency.

Synthesis of nanocrystals is one of the most rapidly advancing areas of nanoscience, and today nanocrystals can be produced with impressive control over their composition, size, shape, polydispersity, and surface chemistry. As such, they are ideal building blocks for fabricating hierarchical architectures with tailorable functionality on every level of the hierarchy. Here an evaporation-driven, template-assisted nanocrystal assembly (ETNA) technique is developed, providing a novel and general approach to fabricating freestanding, 3D, functional architectures using diverse combinations of colloidal nanocrystal species and porous templates of arbitrary geometry. Colloidal PbS (photoluminescent) and CoFe2O4 (superparamagnetic) nanocrystals are template-assembled to fabricate freestanding nanorods and inverse opals, which retain the size-dependent properties of their constituent building blocks while replicating the geometry and preserving the functionality of the templates. Further multifunctionality is demonstrated through mixed-nanocrystal architectures which exhibit the aggregate functionality of their building blocks.

Electroactive polymers (EAP) are an emerging branch of smart materials that possess the capability to change shape in the presence of an electric field. Opportunities for the advancement of knowledge were identified in the branch of EAP consisting of inherently electrically conductive polymers. This dissertation explores methods by which the unique properties of composite materials having conductive polymers as a constituent may be exploited. Chapter 3 describes the blending of polyaniline with conventional thermoplastics. Processing these polyblends into foams yielded a porous conductive material. The effect of blend composition and processing parameters on the resulting porous morphology and electrical conductivity was investigated. These findings represent the first systematic study of porous conductive polymer blends. In Chapter 4, multilayer electroactive polymer actuators consisting of polypyrrole films electropolymerized on a passive polymer membrane core were harnessed as actuators. The membrane is vital in the transport of ionic species and largely dictates the stiffness of the layered configuration. The impact of the mechanical properties of the membrane on the actuation response of polypyrrole-based trilayer bending actuators was investigated. Candidate materials with distinct morphologies were identified and their mechanical properties were evaluated. These results indicated that polyvinylidene difluoride membranes were superior to the other candidates. An electrochemical synthesis procedure was proposed, and the design of a novel polymerization vessel was reported. These facilities were utilized to prepare actuators under a variety of synthesis conditions to investigate the impact of conductive polymer morphology on the electromechanical response. Characterization techniques were implemented to quantitatively assess physical and electrochemical properties of the layered composite. Chapter 5 proposes a new unified multiphysics model that captures the electroactive actuation response inherent to conductive polymer trilayer actuators. The main contribution of this investigation was the proposal and development of a new hybrid model that unifies concepts from charge transport and electrochemomechanical models. The output of the proposed model was compared with published data and shown to be accurate to within 10%. Finally, Chapter 6 demonstrated the application of these materials for use as precision mirror positioners in adaptive optical systems.

Several nanomaterials systems, both inorganic and organic in nature, have been extensively investigated by a number of characterization techniques including atomic force microscopy (AFM), electron microscopy, Fourier transform infrared spectroscopy (FTIR), and energy dispersive x-ray spectroscopy (EDX). The first system consists of boron nitride nanotubes (BNNTs) synthesized via two different methods. The first method, silica-assisted catalytic chemical vapour deposition (SA-CVD), produced boron nitride nanotubes with different morphologies depending on the synthesis temperature. The second method, growth vapour trapping chemical vapour deposition (GVT-CVD), produced multiwall boron nitride nanotubes (MWBNNTs). The bending modulus of individual MWBNNTs was determined using an AFM three-point bending technique, and was found to be diameter-dependent due to the presence of shear effects. The second type of nanomaterial investigated is the biomineralized calcareous shell of the serpulid Hydroides dianthus. This material was found to be an inorganic-organic composite material composed of two different morphologies of CaCO3, collagen, and carboxylated and sulphated polysaccharides. The organic components were demonstrated to mediate the mineralization of CaCO3 in vitro. The final system studied is the proteinaceous cement of the barnacle Amphibalanus amphitrite. The secondary structure of the protein components was investigated via FTIR, revealing the presence of β-sheet conformation, and nanoscale rod-shaped structures within the cement were identified as β-sheet containing amyloid fibrils via chemical staining. These rod-shaped structures exhibited a stiffer nature compared with other structures in the adhesive, as measured by AFM nanoindentation.

Two novel hybrid materials for use in sandwich cores of structural materials are designed, manufactured and mechanically tested. Each material is a hybrid of metal and polymer foam. One set of hybrids is fabricated using an aluminium micro-truss filled with varying densities of polyurethane foam. Increases up to 120% in stiffness, 372% in strength, 740% in resilience and 106% in impact energy over the aluminium micro-truss are obtained from compression and impact testing. Furthermore, the stiffness of these hybrids can be tailored according to the density of the polyurethane foam. Another set of hybrids is fabricated using a rapid prototyped ABS polymer truss that is foamed and electroplated with nanocrystalline nickel. Increases up to 1525% in stiffness, 1165% in strength and 650% in energy absorption over the foamed ABS truss are obtained. Furthermore, the gain in strength, stiffness and energy absorption outweigh the gain in density in these hybrid materials.

This study investigates the possibility of fabricating periodic cellular materials (PCMs) via the lost foam casting (LFC) process using aluminum alloy A356 and magnesium alloy AZ91. This approach combines the structural efficiency of PCM architectures with the processing advantages of near-net-shape LFC. An initial feasibility study fabricated corrugated A356 panels. This was followed by a study of casting variables such as pattern design, vacuum assistance, and alloying additions in order to improve the fillability of the small cross-section struts. Finally, integrated pyramidal sandwich panels having different relative densities were subjected to artificial aging treatments and subsequently tested in uniaxial compression. The A356 PCMs experienced a continuous increase after yielding while the AZ91 PCMs exhibited strut fracture after peak strength. The results showed the compressive yield strengths of this study are comparable with those previously reported PCMs produced by different fabrication methods.

A standard procedure for P3HT:PCBM bulk-heterojunction solar cells has been developed. Fabrication conditions, such as environment; solution concentration, thickness of active layer or post-treatment methods are systematically optimized. The best device performance is obtained by slow-drying spin-coated P3HT:PCBM (1:0.8) blend layer with DCB as solvent. C60:LiF composite films with up to 80% LiF concentration as hole blocking layer have been developed to significantly increase power conversion efficiencies of OPV devices. The short-circuit current density is greatly enhanced, without sacrificing open-circuit voltage and fill factor. Due to its superior oxygen diffusion blocking effect, the C60:LiF composite layer also can provide a more effective passivation film than a thin LiF layer, resulting in an impressive enhancement in air stability of devices.

Porous constructs of calcium polyphosphate (CPP) are under investigation as a substrate for tissue engineering of cartilage for repair of osteochondral defects. Previous studies have shown that CPP has the required features to satisfy these requirements. However, its degradation rate is lower than desired. This study investigated the effect of doping with MgCO3, MgCl2, K2CO3 or KCl at a molar ratio of M/Ca = 0.02 on sintering and in vitro degradation behavior of CPP. Doping with magnesium or potassium improved the tensile and compressive strengths of CPP at similar porosities. After 15 days of aging in phosphate buffer saline, the rate of tensile strength loss was faster for the doped CPP groups than undoped CPP. The chemical degradation rate of Mg-doped CPP groups was the fastest among CPP groups. The chemical degradation rate of K-doped CPP groups was slower than undoped CPP.