This work is aimed on design of a device for testing of fire detectors and various components of fire detection system, communicating with the fire panel over a fire bus or a loop. The device generates voltages, supplying the detectors, as well as communicating over the bus generating communication waveforms and performing detection of responses measuring voltage and current on the connection. The loop signal is processed by the developed unit and data or result sent to a PC utilizing USB or RS232 connection. All the parts of the equipment are galvanically isolated to the loop circuit.

This work is engaged in ways of objects speed measuring mainly helped by Doppler Effect. The sensor HB410 is described in this work and its possible elaboration output heterodyne analog signal. The calculation of objects speed is deduced from frequency of heterodyne signal. In this work is projected circuit solution for elaboration of analog signal and its digitalization. Available types and nature of microcontrollers which are elaborating digital signal and communicating with PC are summarized in this work. In the last chapter is described microcontroller's driving software and PC software for speed measure.

This thesis is at the beginning about designing hardware of I/O card with module \-Rabbit3200 equipped by ethernet. Programs were created in programming languages such as assembler, C and C\#. At the end card was tested by generator, multimeter and oscilloscope.

<p>U disertaciji je prikazan i predložen novi metod merenja snage<br />i energije vetra koji se bazira na stohastičkoj digitalnoj mernoj<br />metodi (SDMM), umesto do sada korišćene standardne sempling<br />metode (SSM). Standard za merenje brzine vetra predstavlja<br />anemometar sa šoljicama, koji na svom izlazu daje sinusni napon<br />čija su amplituda i frekvencija linearno zavisne od brzine<br />vetra. Kako su snaga i energija vetra proporcionalne trećem<br />stepenu brzine vetra, u tu svrhu se primenjuje generalizovan<br />hardver namenjen za računanje proizvoda tri ulazna signala. Zbog<br />niskog frekvencijskog opsega ulaznog signala izvršeno je<br />značajno pojednostavljenje hardvera mernog uređaja. Teorijskom<br />analizom, simulacijom, a potom i eksperimentom potvrđena je<br />hipoteza istraživanja, da se SDMM uspešno može koristiti za<br />merenje snage i energije vetra.</p> / <p>In this dissertation а new wind power and energy measurement<br />method, based on Stochastic Digital Measurement Method (SDMM),<br />was elaborated and proposed, to replace the commonly used Standard<br />Sampling Method (SSM). The standard for wind speed measurement is<br />a cup anemometer that provides a sinusoidal voltage on its output,<br />having the amplitude and frequency linearly dependent of the wind<br />speed. Since the wind power and energy are proportional to the third<br />degree of the wind speed, the general case hardware has been designed<br />for the product calculation over three input signals. The low frequency<br />range of the input signal allows for a significant simplification of the<br />measuring instrument hardware. By theoretical analysis and<br />simulation, and consequently through an experiment the hypothesis of<br />this research was confirmed - that SDMM can be successfully used to<br />measure wind power and energy.</p>

Thesis deals with Datalogger with Ethernet interface controlled by Raspberry Pi 2. Datalogger is equipped with eight digital inputs and three analogue inputs. It allows storage of measured data into the database on the microSD card. It communicates over an Ethernet interface on the Raspberry Pi. The administration and control of the datalogger is possible trought a web server.

This thesis report is about designing a prototype and establishing audio communication between a computer and Digital Signal Processor (DSP) using two preamp circuits using both auxiliary and USB connection. The paper gives the reader an overview on how audio is transmitted from a computer, through the system and to the desired output. The reader should also get a better understanding of how an AD-converter samples the incoming signal to the Discrete plane and how an AUX or phone connector works. This information can be used for designing preamp circuits to communicate between a computer and the DSP. The DSP circuit uses an STM32 processor to control the incoming and outgoing signals with the use of ADC and DAC conversion. The DSP also uses microphones to capture surrounding sound. An addition is to make a prototype on how to use these microphones to  send the signal upstream to the computer. The microphone is then benchmarked with the use of Matlab, calculating Total Harmonic Distortion. Management and optimization of code structure and resources is done in the source files of the project. Using imperative C programing, large functions are broken down into smaller functions to ease readability and control flow. The result is a prototype circuit that can communicate audio signals with both audio jack and USB between computers input and output to the DSP. Using CubeMX in conjunction with CubeIDE to add additional ADC channels to be able to incorporate an automatic source control when the audio jack or USB is connected. / Denna avhandling handlar om att designa en prototyp och etablera ljudkommunikation mellan en dator och en digital signalprocessor (DSP) med hjälp av två förstärkarkretsar genom både aux- och USB-anslutning. Rapporten ger läsaren en översikt över hur ljud skickas från en dator, genom systemet och till önskad utgång. Läsaren bör också få en bättre förståelse för hur en AD-omvandlare fungerar för att sampla den inkommande signalen till tidsdiskreta planet och hur en AUX- eller telekabel fungerar. Målet är att använda denna information för att skapa förstärkare som kan kommunicera mellan en dator och DSP:en. DSP-kretsen använder en STM32-processor för att hantera de inkommande och utgående signalerna med användning av ADC- och DAC-omvandling. DSP:en använder också mikrofoner för att fånga omgivande ljud. Ett tillägg är att skapa en prototyp för hur man kan använda en av mikrofonerna för att skicka signalen till datorn. Mikrofonen jämförs sedan med hjälp av Matlab genom att beräkna total harmonisk distorsion. Hantering och optimering av kodstruktur och resurser görs i projektets källkodsfiler. Genom att använda imperativ C-programmering bryts stora funktioner ned i mindre funktioner för att underlätta läsbarheten och styrningen av flödet. Resultatet är en prototypkrets som kan kommunicera ljudsignaler med både ljuduttag och USB mellan datorns in- och utgång och DSP:en. Genom att använda CubeMX tillsammans med CubeIDE läggs ytterligare ADC-kanaler för att möjliggöra automatisk källkontroll när ljuduttaget eller USB-anslutningen är ansluten.

This master thesis is focused on the theoretical description and practical implementation of software defined transmitter. The main aim of this thesis was made the prototype of software defined transmitter in FM band. Theoretical part is determined to description of basic parts of equipment and working principles to understand the basic principle of digital transmitters and define the appropriate component base for construction. Discussed are used types of A/D and D/A converters, blocks of digital signal processing and the roles, which these components performs. The second part is focused practical. Specified are suitable types of components and block diagram is proposed for following electrical connection and printed circuit board in Eagle program as a plug-in modul for developmental platform Arduino. The main point is program, which sets and controls the transmitter. Next important part is impedance match and antenna tuning, which is explain in practical part of thesis. The result is prototype of software defined transmitter compatible with Arduino Uno platform.