No description available.

No description available.

The increased use of wood composites in building materials results in a need for a better understanding of wood adhesion. The effects of water and temperature exposure on the durability of wood products were assessed using the double-cantilever beam (DCB) method of fracture testing. The relative durability of phenol-formaldehyde (PF) and isocyanate (pMDI) adhesives was compared using a 2-hour boil test and an environmental test. The feasibility of using oriented strandboard (OSB), oriented strand lumber (OSL) and parallel strand lumber (PSL) for the DCB fracture method was assessed. The fracture resistance of PF was reduced significantly by the aging exposures. The fracture resistance of pMDI did not decrease after the 2-hour boil test. The DCB fracture method was shown to be useful with a square-grooved machined specimen using OSB and OSL. / Master of Science

Lo, Kwok Yuen. / Thesis (M.Phil.)--Chinese University of Hong Kong, 2010. / Includes bibliographical references (leaves 52-53). / Abstracts in English and Chinese. / Chapter 1 --- Introduction --- p.1 / Chapter 1.1 --- Background --- p.1 / Chapter 1.2 --- Scope of the thesis --- p.3 / Chapter 2 --- Lifetime Model --- p.4 / Chapter 2.1 --- Introduction --- p.4 / Chapter 2.2 --- Weibull Distribution --- p.4 / Chapter 2.3 --- Step-Stress Experiment --- p.5 / Chapter 3 --- Maximum Likelihood Estimation of Model Parameters --- p.9 / Chapter 3.1 --- Introduction --- p.9 / Chapter 3.2 --- Maximum Likelihood Estimation --- p.10 / Chapter 3.3 --- Fisher Information Matrix --- p.13 / Chapter 3.4 --- Numerical Methods improving Newton's method. --- p.17 / Chapter 3.4.1 --- Initial values --- p.18 / Chapter 3.4.2 --- Fisher-Scoring method --- p.19 / Chapter 4 --- Optimal Experimental Design --- p.21 / Chapter 4.1 --- Introduction --- p.21 / Chapter 4.2 --- Optimal Criteria --- p.22 / Chapter 4.3 --- Optimal Stress-changing-time Proportion --- p.23 / Chapter 4.3.1 --- Optimal n versus the shape parameter B --- p.24 / Chapter 4.3.2 --- "Optimal n versus the parameters ao, a1" --- p.27 / Chapter 4.3.3 --- Optimal n versus the initial stress level x1 --- p.32 / Chapter 4.3.4 --- Optimal n versus the censoring time t2 --- p.33 / Chapter 4.4 --- Sensitivity Analysis --- p.34 / Chapter 4.4.1 --- Effects of the shape parameter B --- p.34 / Chapter 4.4.2 --- "Effects of the parameters ao, al" --- p.37 / Chapter 5 --- Conclusion Remarks and Further Research --- p.39 / Chapter A --- Simulation Algorithm for a Weibull Type-I Censored Simple Step-Stress Model --- p.41 / Chapter B --- Expected values of Fisher Information Matrix --- p.42 / Chapter C --- "Derivation of P(A1, A2)" --- p.50 / Bibliography --- p.52

The predictive values of standard and non-standard germination temperatures, standard accelerated ageing (AA) and saturated salt accelerated ageing (SSAA) tests were investigated. Germination tests were performed at standard and non-standard temperatures of 10°, 20°, 20°/30° and 30°C for cabbage and tomato, and 10°, 15°, 20° and 30°C for onion. The AA and SSAA tests were conducted using four relative humidities: standard AA (RH100), NaCl (RH75), Ca(NO3)2 (RH43) and MgCl2 (RH32). Emergence trials were also conducted at a range of temperatures (winter, 15°/25° and 30°C) and media (Hygromix and soil) using seedling trays. Correlations were calculated to evaluate the relationship between laboratory and emergence test results. Three onion seed lots that have different vigour levels were primed with PEG or NaCl and were germinated and planted under varying temperatures and levels of salinity. There were vigour differences among different seed lots of cabbage, onion and tomato seeds used in this study. Using the different laboratory tests, seed lots were distinguished as high, medium and low vigour seed lots. The low temperature germination test (10°C) for cabbage and onion; and 20°C for tomato were found to be effective for separation of seed lots according to their vigour levels. All SSAA vigour tests were also useful in differentiating seed lots based on their physiological stage of deterioration. Using the standard AA (RH100) the seed moisture content was high (29 to 45%), resulting in fungal growth. However, in the SSAA test the moisture content was below 14% and no fungal growth was observed. Ageing of seed lots using NaCl and MgCl2 resulted in a low narrow range of moisture contents, but using Ca (NO3)2 the range of the moisture content between seed lots was higher. For all crop seeds, there was no significant difference in the percentage emergence between the two growth media but larger seedlings were observed from the commercial growth medium (Hygromix). For cabbage, highly significant correlations were obtained between germination percentage at 10°C and RH32 and all emergence trials. In onion, the correlations were not consistent; highly significant correlations were observed from germination capacity (GC), 15°C, 20°C, 30°C, RH75 and RH32; and emergence parameters at specific conditions. However, the germination percentage from 30°C correlated significantly with the final emergence percentage and seedling vigour index. Germination of tomato seeds at 20°C and all SSAA had highly significant correlation with all emergence parameters. The germination rate parameters: MGT (mean germination time) and GI (germination index) were valuable in categorising seed lots with moderate vigour levels, however, except GE in cabbage and onion, all other germination rate characters failed to correlate with any emergence parameters. The radicle percentage germination (viability or GC) and final emergence percentage (FEP) were not enhanced by priming in all seed lots in the germination and emergence trials at all temperatures. The percentage of normal seedling was increased due to priming when seeds were subjected to low temperature and higher salinity levels. Priming was effective in improving the rate, uniformity of germination/emergence; and increased the seedling dry mass of onion seeds when grown under relatively cold environmental conditions. Priming was more beneficial for low vigour seed lots (seed lot A) than for high vigour seed lots (B, C). Priming also improved germination rate and uniformity at all salinity levels, but faster rate of emergence, more uniform and higher seedling dry mass were only observed when seeds were watered with low salinity levels (25 mM of NaCl). No significant difference was observed using NaCl or PEG as priming agent. Onion seeds are tolerant to salinity during germination and the effect of priming was more beneficial at emergence. / Dissertation (MSc (Agric) Horticulture)--University of Pretoria, 2007. / Plant Production and Soil Science / unrestricted

A unique accelerated aging chamber for experimentally determining the life of nuclear grade high efficiency particulate air (HEPA) filters was designed, implemented, and characterized. A design document was developed under the Nuclear Quality Assurance program (NQA-1). The aging process is achieved by sustaining an elevated humidity condition inside the chamber for an extended period of time. Elevated humidity conditions expose the media to commonly occurring stressors that mimic the degradation a typical filter in practical applications would experience. The aged media may then be analyzed using autopsy methodology resulting in data that can be used to better understand the useful life of HEPA filters. The chamber allows age studies to be conducted in a fraction of the time. The industry requires a more complete understanding of the useful life of HEPA filters as opposed to the rule of thumb which states to dispose filters 10 years after the manufacture date.

The high cost of designing, testing and manufacturing semiconductor chips makes simulation essential to predict performance and power throughout the design cycle of hardware components. However, standard detailed software performance/power simulators are too slow to finish real-life benchmarks within the design cycle. To compensate, reduced accuracy is often traded for improved simulator performance. This dissertation explores the FPGA-Accelerated Simulation Technologies (FAST) methodology that can dramatically improve simulation performance without sacrificing accuracy. Design trade-offs of the functional model partition of a FAST simulator are discussed and QUICK, an implementation of a FAST functional model that is designed to provide fast functional execution as well as the ability to rollback and execute down different paths is described. QUICK is general enough to be useful beyond FPGA-accelerated simulators and provides complex ISA (x86) and full-system support. A complete FAST simulator that combines QUICK with an FPGA-based timing model runs in the millions of x86 instructions per seconds, several orders of magnitude faster than software simulators of comparable accuracy capability, and boots unmodified Windows XP and Linux. Ideally, one could model power at the same speeds as performance modeling in a FAST simulator. However, traditional software-implemented power estimation techniques are very slow. PrEsto, a new power modeling methodology that automatically generates accurate power models that can efficiently fit and operate within FAST simulators, is proposed. Such models can dramatically improve the accuracy and performance of architectural power estimation. Improving high-accuracy simulator performance will open research directions that could not be explored economically in the past. The combination of simulation performance, accuracy, and power estimation capabilities extend the usefulness of such simulators, thus enabling the co-design of architecture, hardware implementation, operating systems, and software. / text

The quantity and length of optical fibers required for the Hobby-Eberly Telescope Dark Energy eXperiment (HETDEX) create unique fiber handling challenges. More than 33,000 optical fibers will enable the Hobby-Eberly Telescope (HET) to collect data on at least one million galaxies that are 9 billion to 11 billion light-years away, yielding the largest map of the universe ever produced [1,2]. The design advantages made possible by optical fibers also forms challenges to prevent damage to the fragile fibers that can lead to Focal Ratio Degradation (FRD) [3]. Therefore, a life cycle test must be conducted to study fiber behavior and measure FRD as a function of time. This thesis describes the design and design methodology of an electro-mechanical test apparatus for accelerated life testing of optical fiber assemblies. The design methodology summarizes the development of functional requirements and constraints that drove the design. The test apparatus design utilizes six linear actuators to replicate the movement of the fiber system deployed on HETDEX for over 65,000 accelerated cycles, simulating five years of actual operation. The electro-mechanical test apparatus will provide insight into the effects of load history on the performance of optical fibers which published data has thus far been lacking. Performance of the electro-mechanical test apparatus will be demonstrated through simulation, modeling and calculations. The test results that will be generated from the accelerated life test will be of great interest to designers of robotic fiber handling systems for major telescopes. / text

Polycrystalline silicon photovoltaic (PV) modules have the advantage of lower manufacturing cost as compared to their monocrystalline counterparts, but generally exhibit both lower initial module efficiencies and more significant early-stage efficiency degradation than do similar monocrystalline PV modules. For both technologies, noticeable deterioration in power conversion efficiency typically occurs over the first two years of usage. Estimating PV lifetime by examining the performance degradation behavior under given environmental conditions is, therefore, one of continual goals for experimental research and economic analysis. In the present work, accelerated lifecycle testing (ALT) on three polycrystalline PV technologies was performed in a full-scale, industrial-standard environmental chamber equipped with single-sun irradiance capability, providing an illumination uniformity of 98% over a 2 x 1.6m area. In order to investigate environmental aging effects, time-dependent PV performance (I-V characteristic) was evaluated over a recurring, compressed day-night cycle, which simulated local daily solar insolation for the southwestern United States, followed by dark (night) periods. During a total test time of just under 4 months that corresponded to a year equivalent exposure on a fielded module, the temperature and humidity varied in ranges from 3 degrees C to 40 degrees C and 5% to 85% based on annual weather profiles for Tucson, AZ. Removing the temperature de-rating effect that was clearly seen in the data enabled the computation of normalized efficiency degradation with time and environmental exposure. Results confirm the impact of environmental conditions on the module long-term performance. Overall, more than 2% efficiency degradation in the first year of usage was observed for all thee polycrystalline Si solar modules. The average 5-year degradation of each PV technology was estimated based on their determined degradation rates.

Background In the treatment of head and neck cancers (HNCs), radiotherapy (RT) has the advantage of organ preservation compared to surgery. However, treatment toxicities associated with RT can affect important functions for everyday life, both in the acute and late stage. RT to macroscopic tumour in HNC is commonly combined with elective RT to cervical lymph nodes at risk of microscopic involvement. The resulting risk reduction of the elective treatment based on dose-volume parameters is sparsely evaluated. So is the relationship between the elective treatment and treatment toxicity. The present thesis addresses these aspects. A strategy aimed at improving the outcome of RT is accelerated fractionation (AF). AF strives to shorten total treatment time to minimise proliferation of the tumour tissue during the RT period. We have investigated the impact of AF on both disease control and toxicity. Methods In the ARTSCAN study, 750 patients with localised HNC were randomised between AF (68 Gy in 4.5 weeks) and conventional fractionation (CF) (68 Gy in 7 weeks). The elective treatment volume was prescribed 46 Gy with CF in both treatment arms. The thesis is based on four individual papers, investigating the issues above in the whole study population or in sub-populations. Results No difference in disease control or late toxicity between CF and AF was observed at five years. However, there was an increased acute toxicity with AF. Weight loss was associated with treatment volume, independent of tumour stage. The elective treatment volume was found to be an independent risk factor for late aspiration, as well as mean dose to the pharyngeal constrictor muscles, neck dissection, and age at randomisation. There was a significant risk reduction for node relapses in volumes treated to an elective dose. Only a relapse in volumes treated to >60 Gy affected the survival. Conclusion The present thesis questions the benefit of AF in definitive RT as well as extensive elective treatment of the cervical nodes.