No description available.

Investigations on size dependent phase stability and transformations in isolated nanoparticles have gained momentum in recent times. Size dependent phase stability generates size specific particle microstructure which consequently yields size specific functionality. One important prerequisite for conducting studies on nanoparticles is their synthesis. A substantial amount of research effort has therefore been focused on devising methodologies for synthesizing nanoparticles with controlled shapes and sizes. The present thesis deals with both these two aspects: (a) synthesis of nanoparticles and (b) phase transformations in nanoparticles. The system chosen in this study is AuCu intermetallic nanoparticles. The choice of AuCu nanoparticle was due to the fact that the literature contains abundance of structural and thermodynamic data on Au–Cu system which makes it a model system for investigating size dependence of phase transformations. With respect to synthesis, the present thesis provides methodologies for synthesizing alloyed Au–Cu nanoparticles of different sizes, Au–Cu nano-chain network structures and uniform Au–Cu2S hybrid nanoparticles. For every type, results are obtained from a detailed investigation of their formation mechanisms which are also presented in the thesis. With respect to phase transformation, the thesis presents results on the size dependence of fcc to L10 transformation onset in Au–Cu nanoparticles under isothermal annealing conditions. The present thesis is divided into eight chapters. A summary of results and key conclusions of work presented in each chapter are as follows. The ‘introduction’ chapter (chapter I) describes the organization of the thesis. Chapter II (literature study) presents a review of the research work reported in the literature on the various methodologies used for synthesizing Au–Cu based nanoparticles of different shapes and sizes and on ordering transformation in AuCu nanoparticles. The chapter also presents a brief discussion on the reaction variables that control the process of nucleation and growth of the nanoparticles in solution. Chapter III titled ‘experimental details and instrumentation’ describes the synthesis procedures that were used for producing various nanoparticles in the present work. The chapter also briefly describes the various characterization techniques that were used to investigate the nanoparticles. The fourth chapter titled ‘synthesis and mechanistic study of different sizes of AuCu nanoparticles’ provides two different methodologies for synthesis, referred as ‘two-stage process’ and ‘two-step process’ that have been used for producing alloyed AuCu nanoparticles of different sizes (5, 7, 10, 14, 17, 25 nm). The ‘two-stage’ process involved sequential reduction of Au and Cu precursors in a one pot synthesis process. Whereas, the ‘two-step’ process involved a two-pot synthesis in which separately synthesized Au nanoparticles were coated with Cu to generate alloyed AuCu nanoparticles. In the two-stage synthesis process it was observed that by changing the total surfactant-to-metal precursor molar ratio, sizes of the alloyed AuCu nanoparticles can be varied. ‘Total surfactants’ here include equal molar amounts of oleic acid and oleylamine surfactants. Interestingly, it was observed that there exists a limitation with respect to the minimum nanoparticle size that can be achieved by using the two-stage process. The minimum AuCu nanoparticle size achieved using the two-stage synthesis process was 14 nm. Mechanism of formation of AuCu nanoparticles in the two-stage synthesis process was investigated to find out the reason for this size limitation and also to determine how the synthesis process can be engineered to synthesize alloyed AuCu nanoparticles with smaller (<14nm) sizes. Studies to evaluate mechanism of synthesis were conducted by investigating phase and size of nanoparticles present in the reaction mixture extracted at various stages of the synthesis process. Their studies revealed that (a) the nanoparticle formation mechanism in the two-stage synthesis process involves initial formation of Au nanoparticles followed by a heterogeneous nucleation and diffusion of Cu atoms into these Au rich seeds to form Au–Cu intermetallic nanoparticles and (b) by increasing the relative molar amount of the oleylamine surfactant, size of the initial Au seed nanoparticles can be further reduced from the minimum size that can be achieved in the case when equal molar amounts of oleylamine and oleic acid surfactants are used. The information obtained from the mechanistic study was then utilized to design the two-step synthesis process. In the two-step process, Au nanoparticles were synthesized in a reaction mixture containing only the oleylamine surfactant. Use of only oleylamine resulted in production of pure Au nanoparticles with sizes that were well below 10 nm. These Au nanoparticles were washed and dispersed in a solution containing Cu precursor. Introduction of a reducing agent into this reaction mixture led to the heterogeneous nucleation of Cu onto the Au seed particles and their subsequent diffusion into them to form alloyed AuCu nanoparticles with sizes of ~5, 7 and 10 nm. The study present in this chapter essentially signified that the surfactants used in the reaction mixture not only prevent nanoparticles from agglomerating in the final dispersion but also control their nucleation and growth and therefore can be used as a tool to tune nanoparticle sizes. The fifth chapter titled ‘size dependent onset of FCC-to-L10 transformations in AuCu alloy nanoparticles’ illustrates the effect of AuCu nanoparticle size on the onset of ordering under isothermal annealing conditions. Nanoparticles in this study were annealed in-situ in a transmission electron microscope. Samples were prepared by drop drying a highly dilute dispersion of as-synthesized nanoparticles onto an electron transparent TEM grid. Nanoparticles sitting on the TEM grid were well separated from each other to minimize particle sintering during the annealing operation. It was however observed that during the isothermal annealing, particle coarsening due to atomic diffusion was appreciable for 5 nm particles but negligible for 7 and 10 nm particles. Therefore for this study only 7 nm and 10 nm sized particles were considered. Onset of ordering was determined from the time when first sign of the diffraction spot, corresponding to the ordered phase, appears in the selected area electron diffraction pattern from a region containing large number of AuCu nanoparticles. Through a series of isothermal experiments it was observed that the time for onset of ordering increased with decrease in size of the nanoparticles. It is speculated that the delay in onset of ordering may be due to the fact that with a decrease in nanoparticle size the probability of a nanoparticle containing a fluctuation that shall generate a thermodynamically stable nuclei of the ordered phase decreases. A sharp interface between the ordered and the disordered phase inside the particle was also observed which suggested that the ordering transformation in as-synthesized fcc AuCu nanoparticles is a first order transformation. The sixth chapter titled ‘synthesis and characterization of Au1-xCux–Cu2S hybrid nanostructures: morphology control by reaction engineering’ provides a modified polyol method based synthesis strategy for producing uniform Au–Cu2S hybrid nanoparticles. Detailed compositional and structural characterization revealed that the hybrid nanoparticles are composed of cube shaped Au-rich, Au–Cu solid solution phase and hemispherical shaped Cu2S phase. Interestingly, the hemispherical Cu2S phase was attached to only one facet of the cube shaped phase. A study on the formation mechanism of hybrid nanoparticles was also conducted by characterizing specimens extracted from the reaction mixture at different stages of the synthesis process. The study revealed that the mechanism of formation of hybrid nanoparticles involved initial formation of isolated cube shaped pure Au nanoparticles and Cu–thiolate complex with a sheet morphology. With increase in time at 180°C, the Cu–thiolate complex decomposed and one part of the Cu atoms that were produced from the decomposition were utilized in forming the spherical Cu2S and other part diffused into the Au nanoparticles to form Au–Cu solid solution phase. The chapter also presents a study on the effect of dodecanethiol (DDT) on achieving the hemisphere-on-cube hybrid morphology. In this study it is illustrated that an optimum concentration of dodecanethiol is required both for achieving size and morphological uniformity of the participating phases and for their attachment to form a hybrid nanoparticle. The seventh chapter titled ‘synthesis of Au–Cu nano-chains network and effect of temperature on morphological evolution’ provides methodology for synthesizing fcc Au– Cu nano-chain network structures using polyvinylprrolidone (PVP) surfactant. It was observed that with increase in the molar amount of PVP in the reaction mixture, morphology of the as-synthesized product gradually changed from isolated nanoparticles to branched nano-chain like. The nano-chains contained twins which indicated an absence of continuous growth and possibility of growth by oriented attachment of initially formed Au–Cu nanoparticles. Both in-situ and ex-situ annealing of the nano-chains led to their decomposition into isolated nanoparticles of varying sizes. Annealing also caused fcc-to¬L10 phase transformation. Investigation of the wave length of perturbation leading to breaking of a nano-chain into particles indicated that the surface energy anisotropy affects the splitting of nano-chain network structure into nano-sized particles. The thesis ends with a last chapter where we have presented possible future extension of current work.

<p>In this work, a simple, less time consuming electrochemical method in the form of an electrochemical sensor has been developed for the detection of PAHs. The sensor was fabricated by the deposition of silver-gold (1:3) alloy nanoparticles (Ag-AuNPs) on ultrathin overoxidized polypyrrole (PPyox) film which formed a PPyox/Ag-AuNPs composite on glassy carbon electrode (PPyox/Ag-AuNPs/GCE). The silver-gold alloy nanoparticles deposited to form the composite were chemically prepared by simultaneous reduction of silver nitrate (AgNO3) and chloroauric acid (HAuCl4) using sodium citrate and characterized by UV-visible spectroscopy technique which confirmed the homogeneous formation of the alloy nanoparticles.</p>

<p>In this work, a simple, less time consuming electrochemical method in the form of an electrochemical sensor has been developed for the detection of PAHs. The sensor was fabricated by the deposition of silver-gold (1:3) alloy nanoparticles (Ag-AuNPs) on ultrathin overoxidized polypyrrole (PPyox) film which formed a PPyox/Ag-AuNPs composite on glassy carbon electrode (PPyox/Ag-AuNPs/GCE). The silver-gold alloy nanoparticles deposited to form the composite were chemically prepared by simultaneous reduction of silver nitrate (AgNO3) and chloroauric acid (HAuCl4) using sodium citrate and characterized by UV-visible spectroscopy technique which confirmed the homogeneous formation of the alloy nanoparticles.</p>

Magister Scientiae - MSc / Polyaromatic hydrocarbons (PAHs) are ubiquitous environmental pollutants that have been shown to be teratogenic, mutagenic and carcinogenic and pose serious threats to the health of aquatic and human life. Several methods have been developed for their determination such as immunoassay, gas chromatography and high performance liquid chromatography (HPLC) in combination with fluorescence or absorbance detection. However, these methods are known to manifest underlying disadvantages such as complicated pretreatment, high costs and time consuming processes. In this work, a simple, less time consuming electrochemical method in the form of an electrochemical sensor has been developed for the detection of PAHs. The sensor was fabricated by the deposition of silver-gold (1:3) alloy nanoparticles (Ag-AuNPs) on ultrathin overoxidized polypyrrole (PPyox) film which formed a PPyox/Ag-AuNPs composite on glassy carbon electrode (PPyox/Ag-AuNPs/GCE). The silver-gold alloy nanoparticles deposited to form the composite were chemically prepared by simultaneous reduction of silver nitrate (AgNO3) and chloroauric acid (HAuCl4) using sodium citrate and characterized by UV-visible spectroscopy technique which confirmed the homogeneous formation of the alloy nanoparticles. Transmission electron microscopy showed that the synthesized nanoparticles were in the range of 20-50 nm. The properties of the composite formed upon deposition of the nanoparticles on the PPyox film were investigated by electrochemical methods. The PPyox/Ag-AuNPs/GCE sensor showed strong catalytic activity towards the oxidation of anthracene, phenanthrene and pyrene, and was able to simultaneously detect anthracene and phenanthrene in a binary mixture of the two. The catalytic peak currents obtained from square wave voltammetry increased linearly with anthracene, phenanthrene and pyrene concentrations in the range of 3.0 x 10-6 to 3.56 x 10-4 M,3.3 x 10-5 to 2.83 x 10-4 M, 3.3 x 10-5 to 1.66 x 10-4 M and with detection limits of 0.169 μM, 1.59 μM and 2.70 μM, respectively. The PPyox/Ag-AuNPs/GCE sensor is simple, has antifouling properties and is less time consuming with a response time of 4 s. / South Africa

Among various nanomaterials, metal nanoparticles are the widely studied ones because of their pronounced distinct properties arising in the nanometer size regime, which can be tailored easily by tuning predominantly their size and shape. During the past few decades, scientists are engaged in developing new synthetic methodologies for the synthesis of metal nanoparticles which can be divided into two broad categories: i) top-down approach, utilizing physical methods and ii) bottom-up approach, employing chemical methods. As the chemical methods offer better control over particle size, numerous chemical methods have been developed to obtain metal nanoparticles with narrow size distribution. However, these two approaches have their own merits and demerits; they are not complementary to each other and also not sustainable for real time applications. Recent focus on the synthesis of metal nanoparticles is towards the development of green and sustainable synthetic methodologies. A solid state route is an exciting prospect in this direction because it eliminates usage of organic solvents thus, makes the overall process green and at the same time leads to the realization of large quantity of the materials, which is required for many applications. However, the major obstacle associated with the development of a solid state synthetic route is the lack of fundamental understanding regarding the formation mechanism of the nanoparticles in the solid state. Additionally, due to the heterogeneity present in the solid mixture, it is very difficult to ensure the proximity between the capping agent and nuclei which plays the most decisive role in the growth process. Recently, employment of amine–borane compounds as reducing agents emerged as a better prospect towards the development of sustainable synthetic routes for metal nanoparticles because they offer a variety of advantages over the traditional borohydrides. Being soluble in organic medium, amine– borane allows the reaction to be carried out in a single phase and due to its mild reducing ability a much better control over the nucleation and growth processes is realized. However, the most exciting feature of these compounds is that their reducing ability is not only limited to the solution state, they can also bring out the reduction of metal ions in the solid state. With the availability of a variety of amine–boranes of varying reducing ability, it opens up a possibility to modulate the nanostructure in both solid and solution states by a judicious choice of reducing agent. Although our current understanding regarding the growth behavior of nanoparticles has advanced remarkably, however, most often it is some classical model which is invoked to understand these processes. With the recent developments in in situ transmission electron microscopy techniques, it is now possible to unravel more complex growth trajectories of nanoparticles. These studies not only expand the scope of the present knowledge but also opens up possibilities for many future developments. Objectives • To develop an atom economy solid state synthetic methodology for the synthesis of metal nanoparticles employing amine–boranes as reducing agents. • To gain a mechanistic insight into the formation mechanisms of nanoparticles in the solid state by using amine–boranes with differing reducing ability. • Synthesis of bimetallic nanoparticles as well as supported metal nanoparticles in the solid state using ammonia borane as the reducing agent. • To develop a new in situ seeding growth methodology for the synthesis of core@shell nanoparticles composed of noble metals by employing a very weak reducing agent, trimethylamine borane and their transformation to their thermodynamically stable alloy counterparts. • Synthesis of highly monodisperse ultra-small colloidal calcium nanoparticles with different capping agents such as hexadecylamine, octadecylamine, poly(vinylpyrrolidone) and a combination of hexadecylamine/poly(vinylpyrrolidone) using the solvated metal atom dispersion (SMAD) method. To study the coalescence behavior of a pair of calcium nanoparticles under an electron beam by employing in situ TEM technique. Significant results An atom economy solid state synthetic route has been developed for the synthesis of metal nanoparticles from simple metal salts using amine–boranes as reducing agents. Amine–borane plays a dual role here: acts as a reducing agent thus brings out the reduction of metal ions and decomposes simultaneously to generate B-N based compounds which acts as a capping agent to stabilize the particles in the nanosize regime. This essentially minimizes the number of reagents used and hence simplifying and eliminating the purification procedures and thus, brings out an atom economy to the overall process. Additionally, as the reactions were carried out in the solid state, it eliminates use of organic solvents which have many adverse effects on the environment, thus makes the synthetic route, green. The particle size and the size distribution were tuned by employing amine–boranes with differing reducing abilities. Three different amine–boranes have been employed: ammonia borane (AB), dimethylamine borane (DMAB), and trimethylamine borane (TMAB) whose reducing ability varies as AB > DMAB >> TMAB. It was found that in case of AB, it is the polyborazylene or BNHx polymer whereas, in case of DMAB and TMAB, the complexing amines act as the stabilizing agents. Several controlled studies also showed that the rate of addition of metal salt to AB is the crucial step and has a profound effect on the particle size as well as the size distribution. It was also found that an optimum ratio of amine–borane to metal salt is important to realize the smallest possible size with narrowest size distribution. Whereas, use of AB and TMAB resulted in the smallest sized particles with best size distribution, usage of DMAB provided larger particles that are also polydisperse in nature. Based on several experiments along with available data, the formation mechanism of metal nanoparticles in the solid state has been proposed. Highly monodisperse Cu, Ag, Au, Pd, and Ir nanoparticles were realized using the solid state route described herein. The solid state route was extended to the synthesis of bimetallic nanoparticles as well as supported metal nanoparticles. Employment of metal nitrate as the metal precursor and ammonia borane as the reducing agent resulted in highly exothermic reaction. The heat evolved in this reaction was exploited successfully towards mixing of the constituent elements thus allowing the alloy formation to occur at much lower temperature (60 oC) compared to the traditional solid state metallurgical methods (temperature used in these cases are > 1000 oC). Synthesis of highly monodisperse 2-3 nm Cu/Au and 5-8 nm Cu/Ag nanoparticles were demonstrated herein. Alumina and silica supported Pt and Pd nanoparticles have also been prepared. Use of ammonia borane as the reducing agent in the solid state brought out the reduction of metal ions to metal nanoparticles and the simultaneous generation of BNHx polymer which encapsulates the metal (Pt and Pd) nanoparticles supported on support materials. Treatment of these materials with methanol resulted in the solvolysis of BNHx polymer and its complete removal to finally provide metal nanoparticles on the support materials. An in situ seeding growth methodology for the synthesis of bimetallic nanoparticles with core@shell architecture composed of noble metals has been developed using trimethylamine borane (TMAB) as the reducing agent. The key idea of this synthetic procedure is that, TMAB being a weak reducing agent is able to differentiate the smallest possible window of reduction potential and hence reduces the metal ions sequentially. A dramatic solvent effect was noted in the preparation of Ag nanoparticles: Ag nanoparticles were obtained at room temperature when dry THF was used as the solvent whereas, reflux condition was required to realize the same using wet THF as the solvent. However, no such behavior was noted in the preparation of Au and Pd nanoparticles wherein Au and Pd nanoparticles were obtained at room temperature and reflux conditions, respectively. This difference in reduction behavior was successfully exploited to synthesize Au@Ag, Ag@Au, and Ag@Pd nanoparticles. All these core@shell nanoparticles were further transformed to their alloy counterparts under very mild conditions reported to date. Highly monodisperse, ultrasmall, colloidal Ca nanoparticles with a size regime of 2-4 nm were synthesized using solvated metal atom dispersion (SMAD) method and digestive ripening technique. Hexadecylamine (HDA) was used as the stabilizing agent in this case. Employment of capping agent with a longer chain length, octadecylamine afforded even smaller sized particles. However, when poly(vinylpyrrolidone) (PVP), a branched chain polymer was used as the capping agent, agglomerated particles were realized together with small particles of 3-6 nm. Use of a combination of PVP and HDA resulted in spherical particles of 2-3 nm size with narrow size distribution. Growth of Ca nanoparticles via colaesence mechanism was observed under an electron beam. Employing in situ transmission electron microscopy technique, real time coalescence between a pair of Ca nanoparticles were detected and details of coalescence steps were analyzed.

Recent advancements in nanotechnology and emerging applications of nanomaterials in various fields have stimulated interest in fundamental scientific research dealing with the size and structure controlled synthesis of nanoparticles. The unique properties of nanoparticles are largely size dependent which could be tuned further by varying shape, structure, and surface properties, etc. The preparation of monodisperse nanoparticles is desirable for many applications due to better control over properties and higher performance compared to polydispersity nanoparticles. There are several methods for the synthesis of nanoparticles based on top-down and bottom-up approaches. The main disadvantage of top-down approach is the difficulty in achieving size control. Whereas, uniform nanoparticles with controllable size could be obtained by chemical methods but most of them are difficult to scale up. Moreover, a separate step of size separation is necessary in order to achieve monodispersed which may lead to material loss. In this context, a post-synthetic size modification process known as digestive ripening is highly significant. In this process, addition of a capping agent to poly disperse colloid renders it highly monodisperse either under ambient or thermal conditions. In addition to size control, digestive ripening is also effective in controlling the structure of nanoparticles in colloidal solution comprising two different elements. Use of co-digestive ripening strategy in conjunction with solvated metal atom dispersion (SMAD) method of synthesis resulted in hetero structures such as core–shell, alloy, and composite nanoparticles. Despite the versatility of digestive ripening process, the underlying mechanism in controlling size and structure of nanoparticles are not understood to date. The aim of this thesis is to gain mechanistic insight into size control of digestive ripening as well as to investigate structure control in various binary systems. Objectives  Study digestive ripening of Au nanoparticles using various alkyl amines to probe the mechanism  Study co-digestive ripening of binary colloids consisting of two metals, Pd and Cu prepared separately by SMAD method  Study co-digestive ripening of binary colloids consisting of a metal (Au) and a semiconductor (CdS) prepared separately by SMAD method  Study vaporization of bulk brass in SMAD reactor and analyse phase, structure, and morphology of various Cu/Zn bimetallic nanoparticles obtained from bulk brass under various experimental conditions Significant results In chapter 1, fundamental processes of nanoparticle formation and common synthetic techniques for the preparation of monodisperse nanoparticles are briefly discussed. Chapter 2 presents a mechanistic study of digestive ripening process with regard to size control using Au nanoparticles as a model system. Three long chain alkyl amine molecules having different chain length were used as digestive ripening agents. The course of digestive ripening process was analysed by UV-visible spectroscopy and transmission electron microscopy. The experimental conditions such as concentration of digestive ripening agent, time, and temperature were found to influence the size distribution of nanoparticles. The average particle size was found to be characteristic of metal-digestive ripening agent combination which is considered as the optimum size preferred during digestive ripening under a given set of experimental conditions. This study discusses stabilization of optimum sized particles, surface etching, and reversibility in digestive ripening. Chapter 3 describes the synthesis and characterization of PdCu alloy nanoparticles by co-digestive ripening method. Syntheses of individual Pd and Cu colloids were carried out by SMAD method. Pd nanoparticles obtained using THF as solvent and in the absence of any capping agent resulted in an extended small Pd nanowire network assembly. Morphological evolution of spherical Pd nanoparticles from Pd nanowire network structure was observed with the use of capping agent, hexadecyl amine (HDA) in SMAD method. Co-digestive ripening of Pd and Cu colloids was studied at various temperatures. This study revealed temperature dependent diffusion of Cu atoms into Pd lattice forming PdCu alloy nanoparticles. Next, co-digestive ripening of a colloidal system comprising a metal and a semiconductor was explored. Au-CdS combination was chosen for this study owing to its interesting photocatalytic properties. Chapter 4 deals with the synthesis of Au and CdS nanoparticles by SMAD method and Au/CdS nanocomposite by co-digestive ripening. CdS nanoparticles of size 4.0 + 1.2 nm and Au nanoparticles of size 5.6 + 1.1 nm were obtained as a result of digestive ripening process. Au/CdS nanocomposite obtained by co-digestive ripening was characterized by a matrix-like structure made up of CdS nanoparticles in which Au nanoparticles were embedded. CdS nanoparticles were found to establish an intimate surface contact with Au nanoparticles and the matrix of CdS surrounding Au was developed via aggregation during digestive ripening. Chapter 5 describes a comprehensive study on various Cu/Zn bimetallic nanoparticles obtained from bulk brass. Vaporization of bulk brass in SMAD reactor led to a deploying process and further growth of nanoparticles from phase separated Cu and Zn atoms formed a composite structure. The characterization of Cu/Zn nanocomposite revealed covering of composite surface with Cu resulting in a core-shell structure, Cu/Zn@Cu. Post-synthetic digestive ripening of these core-shell composite particles showed diffusion of Zn atoms to the composite surface in addition to size and shape modification. Annealing of Cu/Zn nanocomposites prepared in THF resulted in α-CuZn alloy nanoparticles via sequential transformation through η-CuZn5, γ-Cu5Zn8, and β-CuZn (observed as marten site) phases.

[ES] Teniendo en cuenta el agotamiento de los combustibles fósiles y la creciente concentración de CO2 en la atmósfera, la hidrogenación de CO2 es una forma prometedora de convertir el CO2 en productos químicos y combustibles de carbono de alto valor añadido. Considerando la gran influencia del tamaño de partícula, la composición química, la naturaleza del soporte y las condiciones de operación sobre el comportamiento catalítico de los catalizadores, se han desarrollado una serie de catalizadores para la hidrogenación de CO2 basados en metales abundantes no nobles y polisacáridos naturales como precursores del grafeno. En la presente tesis doctoral, las especies metálicas soportadas sobre una matriz de carbono grafítico defectuosa, con diferentes tamaños de partículas, muestran diferente actividad catalítica y selectividad para la hidrogenación de CO2. Se prepararon, de forma controlada, nanopartículas de aleaciones de Co y Co-Fe soportadas en grafenos dopados con N defectuosos, con una amplia distribución de tamaño de nanopartículas, para la reacción de Sabatier, presentando una selectividad a metano superior al 90% con valores de conversión de CO2 superiores al 85%. En el caso de un solo metal, Co o Fe, y sus aleaciones en forma de "clusters" y pequeñas nanopartículas soportadas en el mismo material, la selectividad de la hidrogenación de CO2 cambia a CO, en lugar de metano, obteniéndose un valor del 98 % y alcanzando una conversión de CO2 del 56%. Conviene resaltar que, los catalizadores basados en "clusters" de aleaciones de metal con una carga de metal incluso por debajo del 0.2 % en peso, exhiben una mayor selectividad y rendimiento que los que tienen nanopartículas de aleaciones de Co-Fe más grandes que varían de 1 a 4 nm y una carga de metal más alta en una composición similar. Siguiendo la línea de investigación de hidrogenación de CO2, se desarrollaron una serie de nanopartículas de aleaciones de Co-Fe soportadas sobre grafenos dopados con N defectuosos con distribución de tamaño de nanopartículas controlada en el rango de 7-17 nm, obteniendo una selectividad hacia hidrocarburos C2+ alrededor del 45% y una conversión del CO2 cercana al 60%. Además, se realizó un estudio comparativo de la actividad catalítica de catalizadores similares basados en Co-Fe con promotores e inhibidores para la hidrogenación de CO2, observando su influencia en la conversión y selectividad de CO2. Finalmente, además de los catalizadores basados en Co-Fe, también se han preparado catalizadores basados en Cu-ZnO mediante un método de dos pasos. Estas nanopartículas de Cu-ZnO soportadas sobre grafeno defectuoso dopado con N exhiben una alta selectividad hacia la conversión de CO2 a metanol. / [CA] Tenint en compte l'esgotament dels combustibles fòssils i la creixent concentració de CO2 en l'atmosfera, la hidrogenació de CO2 és una forma prometedora de convertir el CO2 en productes químics i combustibles de carboni d'alt valor afegit. Considerant la gran influència de la grandària de partícula, la composició química, la naturalesa del suport i les condicions d'operació sobre el comportament catalític dels catalitzadors, s'han desenvolupat una sèrie de catalitzadors per a la hidrogenació de CO2 basats en metalls abundants no nobles i polisacàrids naturals com a precursors del grafé. En la present tesi doctoral, les espècies metàl·liques suportades sobre una matriu de carboni grafític defectuosa, amb diferents grandàries de partícules, mostren diferent activitat catalítica i selectivitat per a la hidrogenació de CO2. Es van preparar, de manera controlada, nanopartícules d'aliatges de Co i Co-Fe suportades en grafens dopats amb N defectuosos, amb una àmplia distribució de grandària de nanopartícules, per a la reacció de Sabatier, presentant una selectivitat a metà superior al 90% amb valors de conversió de CO2 superiors al 85%. En el cas d'un sol metall, Co o Fe, i els seus aliatges en forma de "clústers" i xicotetes nanopartícules suportades en el mateix material, la selectivitat de la hidrogenació de CO2 canvia a CO, en lloc de metà, obtenint-se un valor del 98% i aconseguint una conversió de CO2 del 56%. Convé ressaltar que, els catalitzadors basats en "clústers" d'aliatges de metall amb una càrrega de metall fins i tot per davall del 0.2% en pes, exhibeixen una major selectivitat i rendiment que els que tenen nanopartícules d'aliatges de Co-Fe més grans que varien d'1 a 4 nm i una càrrega de metall més alta en una composició similar. Seguint la línia d'investigació d'hidrogenació de CO2, es van desenvolupar una sèrie de nanopartícules d'aliatges de Co-Fe suportades sobre grafens dopats amb N defectuosos amb distribució de grandària de nanopartícules controlada en el rang de 7-17 nm, obtenint una selectivitat cap a hidrocarburs C2+ al voltant del 45% i una conversió del CO2 pròxima al 60%. A més, es va realitzar un estudi comparatiu de l'activitat catalítica de catalitzadors similars basats en Co-Fe amb promotors i inhibidors per a la hidrogenació de CO2, observant la seua influència en la conversió i selectivitat de CO2. Finalment, a més dels catalitzadors basats en Co-Fe, també s'han preparat catalitzadors basats en Cu-ZnO mitjançant un mètode de dos passos. Aquestes nanopartícules de Cu-ZnO suportades sobre grafé defectuós dopat amb N exhibeixen una alta selectivitat cap a la conversió de CO2 a metanol. / [EN] Considering the depletion of fossil fuels and the increasing atmospheric CO2 concentration, CO2 hydrogenation is a promising way to convert CO2 into value-added carbon-containing chemicals and fuels. Taking into account the significant influences of the particle size, chemical composition, nature of the support, and operation conditions on the catalytic performance of catalysts, a series of catalysts for CO2 hydrogenation have been developed based on the use of abundant non-noble metals and natural polysaccharides as graphene precursors. In the present PhD Thesis, metal species supported on defective graphitic carbon matrix with different particle sizes show different catalytic activity and selectivity for CO2 hydrogenation. Under effective control, Co and Co-Fe alloy nanoparticles wrapped on defective N-doped graphenes with a broad nanoparticle size distribution were prepared and performed for the Sabatier reaction, exhibiting a selectivity to methane over 90 % at CO2 conversion values over 85 %. In the case of single Co or Fe metal and their alloys in the form of clusters and small nanoparticles wrapped on the same support, the selectivity for CO2 hydrogenation shifts to CO, rather than methane, reaching a conversion of 56 % with 98 % CO selectivity. It is worth noting that the metal alloy clusters-based catalysts with the metal loading even below 0.2 wt.% exhibit a higher selectivity and better performance than the ones with larger Co-Fe alloy nanoparticles ranging from 1-4 nm and higher metal loading in a similar composition. Following the research line for CO2 hydrogenation, a series of Co-Fe alloy nanoparticles supported on defective N-doped graphenes with controlled nanoparticle size distribution in the range of 7-17 nm are developed, obtaining a selectivity towards C2+ hydrocarbons about 45% with a CO2 conversion close to 60%. In addition, a comparative catalytic activity of similar Co-Fe-based catalysts with promoters and poison has been studied for CO2 hydrogenation to observe their influence on CO2 conversion and selectivity. Finally, besides Co-Fe-based catalysts, Cu-ZnO-based catalysts have also been prepared by a two-step method. These Cu-ZnO nanoparticles supported on N-doped defective graphene exhibit a high selectivity for CO2 conversion to methanol. / Peng, L. (2021). Metal Nanoparticles Wrapped on Defective Nitrogen-doped Graphitic Carbons as Highly Selective Catalysts for C02 Hydrogenation [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/172329