The final thesis determined the properties of alloys formed from mixtures of powders processed by the SLM method. Powders of alloy AlSi12 and EN AW 2618 were fused in the proportion 75 wt. % AlSi12 + 25 wt. % 2618, 50 wt. % AlSi12 + 50 wt. % 2618 and 25 wt. % AlSi12 + 75 wt. % 2618. Metallographic analysis, EBSD analysis and line EDS microanalysis were made on the samples. Tensile test at room temperature and hardness were carried out to determine the mechanical properties. Fractographic analysis was performed after tensile test.

Bulk metallic glasses and multi-principal element alloys represent relatively new classes of multi-component engineering materials designed for satisfying multiple functionalities simultaneously. Correlating the microstructure with mechanical behavior (at the microstructural length-scales) in these materials is key to understanding their performance. In this study, the structure evolution and nano-mechanical behavior of these two classes of materials was investigated with the objective of fundamental scientific understanding of their properties. The structure evolution, high temperature nano-mechanical behavior, and creep of two Zr-based alloys was studied: Zr41.2Ti13.8Cu12.5Ni10.0Be22 (Vitreloy1) and Zr52.5Ti5Cu17.9Ni14.6All0 (Vitreloy105). Devitrification was found to proceed via the formation of a metastable icosahedral phase with five-fold symmetry. The deformation mechanism changes from inhomogeneous or serrated flow to homogenous flow near 0.9Tg, where Tg is the glass transition temperature. The creep activation energy for Vitreloy1 and Vitreloy105 were 144 kJ/mol and 125 kJ/mol, respectively in the range of room temperature to 0.75Tg. The apparent activation energy increased drastically to 192 kJ/mol for Vitreloy1 and 215 kJ/mol for Vitreloy105 in the range of 0.9Tg to Tg, indicating a change in creep mechanism. Structure evolution in catalytic amorphous alloys, Pt57.5Cu14.7Ni5.3P22.5 and Pd43Cu27Ni10P20, was studied using 3D atom probe tomography and elemental segregation between different phases and the interface characteristics were identified. The structure evolution of three multi-principal element alloys were investigated namely CoCrNi, CoCrFeMnNi, and Al0.1CoCrFeNi. All three alloys formed a single-phase FCC structure in as-cast, cold worked and recrystallized state. No secondary phases precipitated after prolonged heat treatment or mechanical working. The multi-principal element alloys showed less strain gradient plasticity compared to pure metals like Ni during nano-indentation. This was attributed to the highly distorted lattice which resulted in lesser density of geometrically necessary dislocations (GNDs). Dislocation nucleation was studied by low load indentation along with the evaluation of activation volume and activation energy. This was done using a statistical approach of analyzing the "pop-in" load marking incipient plasticity. The strain rate sensitivity of nanocrystalline Al0.1CoCrFeNi alloy was determined by in situ compression of nano-pillars in a Pico-indenter. The nanocrystalline alloy demonstrated a yield strength of ~ 2.4 GPa, ten times greater than its coarse grained counterpart. The nanocrystalline alloy exhibited high strain rate sensitivity index of 0.043 and activation volume of 5b3 suggesting grain boundary dislocation nucleation.

Among the commercial aluminum alloys, aluminum 319 (Al-7wt%Si-4wt%Cu) type alloys are popularly used in automobile engine parts. These alloys have good casting characteristics and excellent mechanical properties resulting from a suitable heat treatment. To get a high strength in the 319 type alloys, grain refining, reducing the porosity, solid solution hardening, and precipitation hardening are preferred. All experimental variables such as solidification condition, composition, and heat treatment are influence on the precipitation behavior; however, precipitation hardening is the most significant because excess alloying elements from supersaturated solid solution form fine particles which act as obstacles to dislocation movement. The challenges of the 319 type alloys arise due to small size of precipitate and complex aging response caused by multi components. It is important to determine the chemical composition, crystal structure, and orientation relationship as well as precipitate morphology in order to understand the precipitation behavior and strengthening mechanism. In this study, the mechanical properties and microstructure were investigated using transmission electron microscopy and three dimensional atom probe tomography. The Mn and Mg effects on the microstructure and mechanical properties are discussed with crystallographic study on the iron intermetallic phases. The microstructural evolution and nucleation study on the precipitates in the low-Si 319 type aluminum alloys are also presented with sample preparation and analysis condition of TEM and 3DAP tomography.

Abstract not available

Dilute Mg alloys are exclusively identified for wrought structural applications in automotive industry. Any improvement in mechanical properties of alloys is possible only by grain size refinement and by the development of suitable texture. The grain size, grain size anisotropy and texture in these alloys affect the compatibility stresses in a very complex manner. To launch a full scale study towards understanding the complex deformation mechanisms operating in these alloys, it is necessary to understand the effect of grain size and texture on the mechanical behavior of Mg alloys in a broad or semi-quantitative manner first. Current literature lacks such broad study. In this present study, the effect of grain size, grain size anisotropy and texture evolution on the mechanical properties are examined in order to develop an understanding of the deformation mechanism that control the mechanical properties of a dilute conventionally extruded Mg alloy, AZ21. The approach adopted was to first study the microstructure and texture evolution in this conventionally extruded alloy. Since the grain sizes in these alloys vary over a wide range, it is hence necessary to study the microstructure evolution in a highly quantitative manner. In understanding texture, the present study is only limited to qualitatively evaluating the evolution of fibre component of texture using X-Ray Diffraction spectra. For truly quantitative microstructure evolution results in materials were grains sizes are spread over a wide range, it is critical to study a statistically enough no. of grains. Hence to avoid any sampling error, large montages (about 0.3 sq. mm) were constructed out of a series of high resolution images captured using an optical microscope. The montages so constructed are subjected to extensive image enhancement and various other operations are performed to convert these coloured to binary montages. Information like grain size, diameter etc., can be easily extracted from these binary montages and used for further analysis. Fibre texture in these conventionally extruded dilute Mg alloys generally develops due to alignment of basal planes along the direction of extrusion. The Critical Resolved Shear Stress for basal slip is very low when compared to that of non-basal planes. And also since there are very limited primary slip systems in these dilute Mg alloys, the development of strong fibre texture drastically changes the compatibility stresses and hence the mechanical properties . To broadly study the effect of microstructure-texture on mechanical proerties, after post extrusion annealing, heat treatments representing typical microstructure-texture combinations were identified. Effect of each microstructure-texture combination on the tensile and completely reversed cyclic fatigue properties are studied and qualitatively interpreted. The fibre texture showed pronounced effect on tensile ductility but it hardly affected the yield strength. With just 10% reduction in BPI, the ductility reduced by about 50%. A small change in average grain size did not alter the yield strength. Unlike tensile ductility, fatigue endurance stress was not altered drastically by the change in grain size or texture. But there appeared to be a significant effect of residual stress. In ending, a small change in microstructure-texture combination in these conventionally extruded alloys has a pronounced effect on ductility or in other words plastic properties. But a it has minimal effect on yield strength and fatigue endurance stress.

Metal matrix composites can produce mechanical and physical properties better than those of the monolithic metal. Titanium alloys are widely used matrix materials as they can offer outstanding specific strength, corrosion resistance and other advantages over its competitors, such as aluminium, magnesium and stainless steel. In past decades, titanium matrix composites served in broad areas, including aerospace, military, automobile and biomedical industries. In this project, a revised powder metallurgy method, which contains cold isostatic pressing and hot isostatic pressing, was adopted to refine the microstructure of monolithic titanium. It was also used to manufacture titanium matrix composites. TiH2 powder was selected as the starting material to form Ti matrix and the reinforcements were sub-micron and nano-metric TiB particles. Mechanical properties and microstructure of commercial titanium composites exhaust valves from Toyota Motor Corporation have been studied as the reference of properties of titanium composites manufactured in this project. It has been shown that tensile strength and hardness of exhaust valves increase about 30% than those of similar matrix titanium alloys. Examination on powder starting materials of this project was also carried out, especially the dehydrogenation process shown in the DSC result. Mechanical properties and microstructures of titanium matrix composites samples in this project, as related to the process parameter, have also been investigated. The density of these samples reached 96% of theoretical one but cracks were found through out the samples after sintering. Fast heating rates during the processing was suspected to have caused the crack formation, since the hydrogen release was too fast during dehydrogenation. Hardness testing of sintered samples was carried out and the value was comparable and even better than that of commercial exhaust valves and titanium composites in literature. Microstructure study shows that the size of reinforcements increased and the size of grains decreased as the increasing amount of TiB reinforcements. And this condition also resulted in the increasing amount of the acicular alpha structure.

Orientador: Rubens Caram Junior / Tese (doutorado) - Universidade Estadual de Campinas, Faculdade de Engenharia Mecânica / Made available in DSpace on 2018-08-23T09:33:56Z (GMT). No. of bitstreams: 1 Lopes_EderSocratesNajar_D.pdf: 9279894 bytes, checksum: a2ed77cd79f48134e7daf5bc705afb0e (MD5) Previous issue date: 2013 / Resumo: Ligas de Ti do tipo ? metaestável exibem comportamento singular no tocante à possibilidade de manipulação de seu comportamento mecânico. Nessas ligas, a rigidez pode ser alterada por meio do controle das fases presentes, o que permite que esses materiais sejam incluídos no seleto grupo dos materiais com gradientes funcionais (functionally graded materials - FGM). Neste trabalho, objetivou-se projetar, produzir, processar, caracterizar e aplicar ligas Ti-Nb com adições do elemento ? estabilizador de baixo custo Fe. As ligas foram produzidas por fusão a arco voltaico e submetidas a diversas condições de tratamento térmico, incluindo solubilização acima da temperatura ?-transus, resfriamento rápido até a temperatura ambiente e tratamentos térmicos de envelhecimento entre 260 °C e 400 °C. A caracterização envolveu calorimetria diferencial de varredura, difração de raios-X e dureza Vickers em alta temperatura, análises metalográficas e de módulo de elasticidade por técnicas acústicas, ensaios de tração e mapeamento de rigidez por meio de nanoindentação. Os resultados obtidos mostram a retenção completa da fase ? para a liga Ti-30Nb-3Fe solubilizada e resfriada rapidamente e permitem também, compreender a decomposição da fase martensita ?" e a nucleação das fases ? e ?. A adição do elemento Fe tornou a cinética de transformação de fases bem mais lenta, propiciando, sob algumas condições, a supressão da fase ?, que é conhecida por aumentar a dureza em detrimento da ductilidade. Tais resultados foram utilizados no estabelecimento de condições ideais de processamento que permitem obter componentes ortopédicos com rigidez gradual. Finalmente, o conhecimento adquiro foi usado na fabricação de placas e parafusos de osteossíntese a partir da liga Ti-30Nb-3Fe com gradientes de funcionalidade / Abstract: Metastable ? Ti alloys exhibit singular behavior regarding the possibility of manipulating their mechanical behavior. In these alloys, the stiffness can be changed by controlling phases, which allows these materials to be included in the select group of functionally graded materials (FGM). This study aimed to design, produce, process, characterize and apply Ti-Nb alloys with addition of Fe, an inexpensive ? stabilizing element. These alloys were produced by arc melting and subjected to different heat treatment conditions, including solution above the ?- transus temperature, quenching to room temperature and aging heat treatments between 260 °C and 400 °C. Characterization involved differential scanning calorimetry, X-ray diffraction and Vickers hardness at high temperature, metallographic analyzes, elastic modulus by acoustic techniques, tensile test and stiffness mapping via nanoindentation. The results obtained show complete retention of the ? phase in the Ti-30Nb-3Fe alloy after solution in the ? field and rapid cooling to room temperature and also allow understanding martensite ?" decomposition and nucleation of the ? and ? phases. It was found that Fe additions make the phase transformation kinetics much slower, providing, for some conditions, suppression of the ? phase precipitation, which is known to increase the hardness at the expense of ductility. These results were used to establish optimal processing conditions, resulting in orthopedic component with graded stiffness. Finally, the knowledge acquired was used in the manufacturing of osteosynthesis plates and screws with functionality graded from the Ti-30Nb-3Fe / Doutorado / Materiais e Processos de Fabricação / Doutor em Engenharia Mecânica

Titanium alloys are important engineering alloys that are extensively used in various industries. This is due to their unique combination of mechanical and physical properties such as low density combined with high strength and toughness as well as outstanding corrosion resistance. An additional benefit associated with Ti alloys, in general, is that their properties are relatively temperature-insensitive between cryogenic temperature and ~500 °C. Amongst the Ti alloys, Ti-6Al-4V (referred as Ti64) is a widely used alloy. Conventionally cast Ti64 possesses classical Widmanstätten microstructure of (hcp) α and (bcc) β phases. However this microstructure suffers from large prior β grain size, which tends be in the order of a few mm. Such large grain sizes are associated with poor processability as well as inferior mechanical performance. The necessity to break this coarse as-cast microstructure down, through several successive thermo-mechanical processing steps, adds considerably to the cost of finished Ti alloy products, making them expensive vis-à-vis other competing alloys. The addition of small amount of B (~0.1%) to Ti64 alloys, on the other hand reduces the cast grain size from couple of mm to ~200 µm. Moreover, addition of B to Ti alloys produces the intermetallic TiB needles during solidification by an in situ chemical reaction. The overall objective of this work is to gain insights into the role of microstructural modifications, induced by B addition to Ti64, on the mechanical performance of the alloys, in particular the room temperature damage tolerance (fracture toughness and fatigue crack growth) characteristics. The key questions we seek to answer through this study are the following: (a) What role does the microstructural refinement plays on the quasistatic as well as fracture and fatigue behavior and high temperature deformability of the alloys? (c) A hierarchy of microstructural length scales exist in Ti alloys. These are the lath, colony and grain sizes. Which of these microstructural parameters control the mechanical performance of the alloy? (b) What (possibly detrimental) role, if any, do the TiB needles play in influencing the mechanical performance of Ti64 alloys? This is because TiB being much stiffer, strain incompatibility between the matrix and the TiB phase could lead to easy nucleation of cracks during cyclic loading as well as can pose problems during dynamic deformation. (d) What is the optimum amount of B that can be added to Ti64 such that the most desirable combination of properties can be achieved? Five B-modified Ti64 alloys with B content varying from 0.0 to 0.55 wt.% were utilised to answer the above questions. Marked prior β grain size reduction was noted with up to 0.1 wt.% B addition. Simultaneous refinement of α/β colony size has also been observed. The addition of B to Ti64, on the other hand increases the α lath size. The TiB needles that form in-situ during casting are arranged in a necklace like structure surrounding the grain boundaries for higher B added Ti64 alloys. An anomalous enhancement in elastic modulus, E, of the alloy with only 0.04 wt.% B to Ti64 was found. E has been found to follow the same trend of variation with B content at higher temperatures (up to 600 °C) as well. Nanoindentation experiments were conducted to evaluate the moduli of the various phases present in the microstructure and then rationalize the experimental trends within the framework of approximate models. Marginal but continuous enhancement in strength of the alloys with B addition was observed. It correlates well with the grain size refinement according to Hall-Petch relationship. Ductility on the other hand increases initially with up to 0.1 wt.% B addition followed by a reduction. While the former is due to the microstructural refinement, the latter is due to the presence of significant amount of brittle TiB phase. Room temperature fracture toughness decreases with B addition to Ti64. Such reduction in fracture toughness with the refinement of prior β grain size has been justified with Ritchie-Knott-Rice model. Contradictory roles of microstructural refinement have been observed for notched and un-notched fatigue. While reduction in length scale has a negative role in crack propagation, it enhances the fatigue strength of the alloy owing to better resistance to fatigue crack initiation. TiB needles on the other hand act as sites for crack initiation and hence limit the enhancement in fatigue strength of alloys with 0.30 and 0.55 wt.% B. An investigation of the high temperature deformability of the alloys has been performed over a wide range of temperature (within the two phase α+β regime) and strain rate windows. Results show that microstructural refinement does not alter the high temperature deformation characteristics as well as optimum processing conditions of the alloys. TiB needles, however act as sites for instability owing to differences in compressibility between the matrix and the whisker phase. In summary, this study suggests that the addition of ~0.1 wt.% B to Ti64 can lead to the elimination of certain thermo-mechanical processing steps that are otherwise necessary for breaking the as-cast structure down and hence make finished Ti components more affordable. In addition, it leads to marginal enhancement in the quasi-static properties and significant benefits in terms of high cycle fatigue performance.

Ni/TiC metal matrix composites have been processed using the laser engineered net shaping (LENS) process. As nickel does not form an equilibrium carbide phase, addition of a strong carbide former in the form of titanium reinforces the nickel matrix resulting in a promising hybrid material for both surface engineering as well as high temperature structural applications. Changing the relative amounts of titanium and carbon in the nickel matrix, relatively low volume fraction of refined homogeneously distributed carbide precipitates, formation of in-situ carbide precipitates and the microstructural changes are investigated. The composites have been characterized in detail using x-ray diffraction, scanning electron microscopy (including energy dispersive spectroscopy (XEDS) mapping and electron backscatter diffraction (EBSD)), Auger electron spectroscopy, and transmission (including high resolution) electron microscopy. Both primary and eutectic titanium carbides, observed in this composite, exhibited the fcc-TiC structure (NaCl-type). Details of the orientation relationship between Ni and TiC have been studied using SEM-EBSD and high resolution TEM. The results of micro-hardness and tribology tests indicate that these composites have a relatively high hardness and a steady-state friction coefficient of ~0.5, both of which are improvements in comparison to LENS deposited pure Ni.

Since NiTi shape memory alloy (SMA) was discovered in the early 1960s, great progress has been made in understanding the properties and mechanisms of NiTi SMA and in developing associated products. For several decades, most of the scientific research and industrial interests on NiTi SMA has focused on its superelastic applications in the biomedical field and shape memory based “smart” devices, which involves the low strain rate (around 0.001 s^-1) response of NiTi SMA. Due to either stress-induced martensite phase transformation or stress induced martensite variant reorientation under the applied load, NiTi SMA has exhibited a high damping capacity in both austenitic and martensitic phase. Recently, there has been an increasing interest in exploitation of the high damping capacity of NiTi SMA to develop high strain rate related applications such as seismic damping elements and energy absorbing devices. However, a systematic study on the influence of strain, strain rate and temperature on the mechanical properties, phase transformation, microstructure and crystal structure is still limited, which leads to the difficulties in the design of products being subjected to high strain rate loading conditions. The four main objectives of the current research are: (1) achieve the single loading and the control of strain, constant strain rate and temperature in high strain rate compression tests of NiTi SMA specimens using Kolsky (split Hopkinson) compression bar; (2) explore the high strain rate compressive responses of NiTi SMA specimens as a function of strain (1.4%, 1.8%, 3.0%, 4.8%, and 9.6%), strain rate (400, 800 and 1200 s^-1), and temperature (room temperature (294 K) and 373 K); (3) characterize and compare the microstructure, phase transformation and crystal structure of NiTi SMAs before and after high strain rate compression; and (4) correlate high strain rate deformation with the changes of microstructure, phase transformation characteristics and crystal structure. Based on the results from this study, it was found that: (1) the compressive stress strain curves of martensitic NiTi SMAs under quasi-static loading conditions are different from those under high strain rate loading conditions, where higher strain hardening was observed; (2) the critical stress and stress plateau of martensitic NiTi SMAs are sensitive to the strain rate and temperature, especially at 373K, which results from the interplay between strain hardening and thermal softening; (3) the microstructure of martensitic NiTi SMA has changed with increasing strain rate at room temperature (294 K), resulting in the reduction in the area of ordered martensite region, while that area increases after deformation at elevated temperature (373K); (4) the phase transformation characteristic temperatures are more sensitive to deformation strain than strain rate; (5) the preferred crystal plane of martensitic NiTi SMA has changed from (11 ̅1)M before compression to (111)M after compression at room temperature (294 K), while the preferred plane remains exactly the same for martensitic NiTi SMA before and after compression at 373 K. Lastly, dynamic recovery and recrystallization are also observed after deformation of martensitic NiTi SMA at 373K.